Most car enthusiasts have sufficient knowledge and skills to work with tools to help take care of the car every day, investing in it to the maximum of their capabilities. Any of them is able to perform simple and affordable maintenance of the main components of the machine. For example, replace air and oil filters or seal a punctured tire. They don't need to be told how to change a burned-out license plate light bulb, they find information on the Internet. Our car enthusiasts can competently check the presence of power in individual car wiring harnesses and, if necessary, easily deal with the car's license plate light bulb holder.

Important! The advantages of such work are obvious - it is easier to change the light bulb on your own than to rely on car service masters. It will be faster, cheaper and more reliable. There are plenty of skills in working with metal and electricity, there would be a desire to change something.

The serviceability of headlights, lamps and dimensions on a car is easily controlled without the use of special equipment by valiant police officers. Even such a minor flaw as a non-working license plate light threatens the car owner with a fine of a couple of thousand rubles. Replacing the license plate light, even in road conditions, does not require much work and money. If there is no spare and there is no auto shop nearby, you can use the interior light bulb.

Before deciding to change the light bulb, you should establish the reasons why the backlight may not work. Perhaps there is no contact in the cartridge, a fuse has blown, or a break in the car's wiring has occurred.

We check the possible reasons for the lack of backlight

From simple to complex:

• we clean the ceiling lamps with a rag, remove all dirt and moisture, by inspection we try to determine the fact of the darkening of the lamp, the presence of condensate and possible deformation of the plastic under the influence of heat;
• turn on the light. If one of the backlights works, there are no questions about the health of the fuses and wiring. If light tapping on the surface of the lampshade gives short-term light bulbs, it is necessary to more tightly settle the lamp in the cartridge;
• remove the fixing clips and remove the decorative trim that blocks access to the lamp wiring connectors. Further, all actions are carried out with the ignition off;
• disconnect the wiring, in most designs the connector is fixed on the cartridge with a latch;
• to remove the cartridge with the lamp, it is enough to turn it by hand at a certain angle around its axis and pull it out of the socket. The angle of rotation for different manufacturers can be from 40 to 90 degrees;
• replacement of the license plate light bulb is done by replacing it with a similar or LED light bulb.

We assemble the cartridge in the reverse order and, if successful, install the fastening of the trunk lid trim.

Important! Before removing the socket with the lamp, it is imperative to remove the wiring connector or turn off the power supply to prevent a short circuit in case of destruction of the socket or contact contacts

The incandescent bulb used in number plate lighting fixtures has a power of 5W, contacts without the use of a base are displayed on the sealed part of the glass cylinder. To replace burnt-out ones, Valeo and Narva lamps are available on the market. Typically, the life of bulbs installed by the manufacturer on a new car averaged at least 2.5 years. Lamps - substitutes offered for free sale, serve two times less.

Factors Affecting Lamp Life

The modern global automotive industry everywhere uses a huge number of components and assemblies made in China. These include almost all minor interior details, plastic products, wiring elements and all kinds of fasteners. The quality of parts and materials corresponds to the class of the machine.

The percentage of failure of all kinds of clips, fasteners, clamps on cars of class "D" is much lower than in cars of class "B", "A" and even "C" that are similar in purpose. The specifics of production and quality control of higher-class automotive equipment implies the use of higher quality materials. The accuracy of manufacturing and the quality of plastic clamps, a lantern and a cartridge in which the backlight is installed, make it possible to perform work with almost bare hands, without special pullers or pliers. The question - how to change the number plate light bulb, is solved without contacting specialists or the machine's operating manual.

For example, replacing the backlight of a license plate lamp on a Toyota Camry 6 is done with a conventional slotted screwdriver in a matter of minutes. To do this, by removing the fastening clips, lift the edge of the trunk lid trim. Feeling the wiring harness with your hand, we find the connector for its fastening on the lamp and, by pressing the connector lock, disconnect it from the lamp. We turn the cartridge with the backlight by 30-40 degrees and pull it out from under the decorative panel. How to replace the license plate light bulb next - we take out the burnt one and install a new lamp or LED. The quality of the plastic makes it possible even after 5-10 years of car operation to disassemble and assemble the fasteners effortlessly without breaking the clamps or the cartridge.

Chinese cars have the worst reputation in this matter. All shades, fasteners, clamps - everything that is made of plastic must be immediately glued to the place of attachment with silicone "sealant", fixed with self-tapping screws or bolts. Moreover, most plastic assemblies, which at first glance seem to be collapsible, fall apart when trying to repair them. The node has to be replaced with a new one.

The question of how to replace the rear license plate light bulb on the Kia Rio has been cleverly resolved. Unlike the common replacement procedure with the removal of the inner lining, in a Korean small car, the lamp itself is removed using a conventional slotted screwdriver. A groove is made next to the plafond, into which we insert the tool and with a little effort we move the lamp body by 3-4 mm. Gently pressing the fastening latches, we easily remove the flashlight from the socket. Further, the sequence of actions on the Kia Rio when replacing the number plate lights is standard.

Replacing a light bulb in the backlight of the number on the Priore

The Russian auto industry is famous for its non-standard approach to detail. Replacing the license plate light bulb on the Priore is no exception, although it does not present any particular difficulties for a trained motorist. Access to the cartridge with the license plate light is from the inside, so it is necessary to remove the inner lining of the trunk lid. The cartridge should be easily removed by hand after turning it 90 degrees. The light bulb is removed from the cartridge and replaced with a new one.

Attention! When overheated, the cartridge and the ceiling are deformed, the assembly can only be disassembled using a tool, while the risk of cutting hands with fragments of plastic and glass increases

The life of the backlight, in addition to the quality of its manufacture, is affected by the quality of fastening in the cartridge, the absence of corrosion on the contacts and condensate accumulating from the moisture of fog and rain. In conditions of unreliable or damp contact, the amount of heat generated by electric current during lamp operation increases sharply. In this case, the car's power supply system works with overload, giving out additional energy to heat the contacts, the plastic from which the cartridge and the transparent cover are made. After a while, the lamp burns out due to the increased heat load.

Attention! Under the influence of heat, the cartridge and the lampshade are deformed; when removing the lamp, care must be taken because of possible cuts to the hands by fragments of glass and plastic

Video on replacing the lamp on the Priore:

Features of lamp replacement work

When carrying out work, the fastenings of ceiling lamps and cartridges massively crack and fail. There are many complaints about the quality of the plastic from which the elements of the lamp are made. Almost always, the question - how to change the number plate backlight lamp is solved by purchasing a whole lamp in the kit and then installing it using glue and self-tapping screws.

If the manufacturer or the previous owner of the car did not install LED lamps in the backlight of the number, do not be too lazy to make such a replacement yourself. Many motorists do not know the specifics of the issue - how to change the number plate light bulb on the Priore to an LED. In auto shops there are many options for such bulbs. As a rule, there are no problems when installing LEDs, but attention and accuracy are required. If LED lamps with four pins instead of two are used, it is necessary to bend the extra contact antennae so that they do not cause a short circuit during installation. They last much longer than incandescent bulbs.

Which number plate lights to install on personal vehicles, each motorist decides on his own. How to replace backlight bulbs on a Toyota Camry can be viewed in the video:

The backlight of the number usually consists of (or also known as W5W). This is an ordinary lamp without a base. Sooner or later they burn out and need to be replaced. So on mine, one is out of order and needs to be replaced. Today I am posting a small instruction on how to replace it with my own hands. I would like to note that on many cars the replacement takes place in a similar way, so it will be useful to everyone ...

You need to change the lamps, otherwise the backlight looks “wretched”, half of the room is illuminated, and half is not! YES, and the traffic police do not like it, but why provoke them once again.

Bug and lamps

When the “backlight” burns out on the AVEO, “CODE 24” occurs, you need to disassemble the lantern and change the element. I would like to note right away that when installing the LED lamp, the error also remained, although it glowed, it can be seen that it has too little voltage or “amperage”, so the on-board computer does not see it! Take note. If you put "normal" no errors will occur.

So I went to an auto parts store and bought the most common option, i.e. "T10" without LEDs. I didn’t take super brands, I bought a proven OSRAM, they had been on the previous one for several years, and everything was fine. In general, the issue price is about 25 rubles.

DIY replacement

As usual, they are mounted in a "niche" in front of the license plate - these are two built-in flashlights. On different cars, they are attached in different ways, some are screwed on - this was the case on some VAZ models, others are simply inserted into the latches - this is practiced on many foreign cars (I have just such an option).

To remove it, you just need to pick it up with a screwdriver, but be careful, because if you bend the wrong corner, you can simply break it. Read the forums according to your model, most likely the people have already changed. For me, this corner is closer to the middle of the trunk lid, or to the opening handle, just hook it up and pull out the lantern.

It is closed with a casing, it is he who protects against dirt getting inside. Now we need to unscrew the lamp mount and pull it out of the cartridge.

Of course, many readers may say - "why do we need this easy instruction"? The guys are “needed”, some beginners almost begin to remove the skin, although everything is elementary here. It is also important to pick up the flashlight from the right side, otherwise you will simply break it. It comes out really effortlessly.

The lamps responsible for providing illumination of the registration number in the Renault Logan model family can rather infrequently disturb the owner with their failure. Such an element burns out after about 1-1.5 years. The process of replacing the lamp is quite simple, so even an inexperienced motorist can cope with such a “task”.

Using the instructions below for Renault Logan, the license plate light bulb is replaced within 15-20 minutes.

What types of lamps are suitable for room lighting in Logan?

These elements are the same as the number plate lamp used for Renault Logan marker lights and are marked "12V W5W". Still similar lighting devices can be found in the interior light ceiling and in the glove box backlight unit.

If you need to replace the license plate light bulb, then you can purchase W5W elements at any specialized trade network. Their cost varies depending on the degree of "famousness" of the manufacturer and the quality of the product itself.

Here are the prices for some options for 12V W5W lamps, for Renault Logan per unit:

• "KOITO" (1583) - 25 rubles. and higher;
• "PHILIPS" (P-12961) - start from 30 rubles;
• "BOSCH": model "Pure Light" (1987302206) - 25 rubles. and more;
• "OSRAM" (O-2825) - from 20 rubles.
• "PHILIPS": modification "LONGLIFE ECO VISION" with an increased resource - from 45 rubles;
• "OSRAM": the version of "Ultra Life", which also has a more significant service life - the most expensive, from 50 rubles.

When choosing an option, we recommend refusing to consider cheap (mostly Chinese) copies of dubious quality for Renault Logan. Their resource is not great, and one cannot do without a characteristic darkening, which will make the backlighting of the number very dim. To guarantee the extended life of this element, it is recommended to lean towards the purchase of resource-intensive and high-quality lamps marked as such:

• "LONGLIFE ECO VISION";
• Ultra Life.

If you are not happy with the boring lamp for backlighting the incandescent number, we recommend choosing an LED analogue of identical parameters (“12V W5W”). Their lighting tint is close to white, and the light output efficiency is much better. Note that the resource of the diode versions is much higher than that of the "obsolete" elements with an incandescent filament.

How to replace the lamp?

Replacing the number plate light bulb is not a difficult procedure at all.

• Using a thin screwdriver with a flat tip, gently wring out the fixing element of the ceiling and take it out.
• When the cartridge is completely removed from the seat in the Renault Logan rear bumper, disconnect its power connector.
• By pressing the latches, carefully remove the transparent diffuser.
• We remove the old lamp, instead of which we install a new analogue.

Before directly performing the replacement procedure, we turn on the backlight mode, only after that we begin these manipulations. LEDs have polarity, therefore, if after installation they did not work, we simply turn them over (by 180 degrees) - the devices should “come to life”.

When only one number plate lamp has become unusable, we recommend that you do not neglect checking the second one. If the working surface of the latter has turned black, it is better to replace it in advance, since the “ceremonial” burnout is about to take place.

To ensure a long service life, purchase only high-quality elements with an increased standard period or diode versions. The Renault factory resorts to installing lamps courtesy of the OSRAM brand.

If the ceiling itself has a malfunction (the diffuser surface has burst or cracked), then it can be purchased by ordering the original code 8200480127 from the manufacturer Renault-Nissan.

Rear license plate lighting is a must for every car. For the maintenance of this external lighting device in a faulty condition or in a condition that does not comply with the norms of the law, several types of administrative punishment are provided: a warning, a fine, deprivation of rights. This article will tell you about what the rear license plate light should be like, how to upgrade it and what rules should be followed.

Legal aspects

In accordance with the regulations of the Rules of the Road (SDA), each car must have a rear license plate light, which is activated at the moment the side lights are turned on. This external light device must be turned on while the vehicle (V) is moving with the onset of darkness. At the same time, the brightness of the lamps should be sufficient for the inspector to be able to identify the state. car number from a distance of 20 meters. Lack of backlighting or a car number that is unreadable for some reason is regarded as a violation and, in accordance with Article 12.2, part 1 of the Code of Administrative Offenses of the Russian Federation, entails a warning or a fine of 500 rubles.

It is possible to correct the situation and thereby improve the illumination of the registration plate by upgrading the standard lamps. The most common way is to install LED light sources: modules, rulers, ribbons. However, this innovation can be regarded as a change in the design of the car with all the ensuing consequences.

The Appendix to the SDA of the Russian Federation says that it is prohibited to make changes to the design of the vehicle without the permission of the traffic police of the Russian Federation (clause 7.18 - Other structural elements). This paragraph can be interpreted as follows. Firstly, if the car does not participate in traffic (is not operated), then it is impossible to detect a violation. Secondly, if the changes made have been certified by the traffic police and have documentary evidence, then the modernization was made according to the law.

In GOST 8769-75 (updated on 08/01/2013) in paragraph 2.8.2 it is said that the rear registration plate of the car must be illuminated by a stream of white light. According to this paragraph, a ban on backlighting the number plate with any other light, except for shades of white, is automatically set. It turns out that the bright and juicy colors of LEDs (blue, red, green) by law cannot be used in the organization of rear number plate lighting. They can obscure and confuse the drivers of vehicles following behind.

This violation is interpreted by the inspector under Article 12.5 Part 1 of the Code of Administrative Offenses of the Russian Federation with a warning or an administrative fine of 500 rubles. Another thing is the illumination of the front number. According to all regulatory documents, it should be absent.

Punishment for installing backlight state. front numbers will be more stringent - deprivation of rights for 6-12 months. with confiscation of lighting fixtures (art. 12.5 part 3).

Taking into account the current standards and rules, we come to the conclusion that it is possible to remake the backlight of the rear number plate with an LED one with your own hands, but without too much fanaticism. The main thing is not to attract the attention of officials with too bright light, illuminating not only the sign, but also part of the roadway, and not to make a multi-colored decoration out of the illumination of the car number.

Ways to upgrade the backlight of the number

Spiral bulbs used in rear license plate lights are the easiest to replace with similar LED bulbs. In a standard C5W base, you can buy LED lamps of various sizes: from to COB matrices. Their main advantage is that they do not cause errors in the on-board computer. Prices for a kit vary greatly and depend on the type of LEDs installed, their power and manufacturer. On average, 2 pieces can be purchased for $5. The standard license plate lighting can be easily replaced with ready-made LED modules specially designed for this purpose. Their geometric dimensions are exactly the same as the regular ceiling lamps, that is, there is no need to redo the fasteners. The cost of a set of two modules of the budget series is $10-15. A cheaper option is to illuminate the number plate based on a sealed LED strip with IP67 or IP68. In this case, you do not even have to dismantle the standard lights. The LED strip is glued over the state. number or along its perimeter on a clean, fat-free base. All that is required of the driver is to switch the power from standard lamps to LED strip, observing the polarity and ensuring the tightness of the contacts.

Renault Logan numbers

Automobile: Renault Logan.
asks: Saltykova Marina.
Essence of the question: How replace a light bulb rear number plate lights?

Please tell me how to replace the rear license plate light bulb Renault Logan? Everything is just so closed there, I don’t even know where to start.

When any of the bulbs on your car fails, you can notice this problem quite simply, however, on Renault Logan, like on any other car, there is also such a light element that is hardly noticeable during daylight hours - a light bulb number plate lights.

Detailed illustration for replacing the backlight bulb (photo algorithm)

In order to carry out such a simple operation, just follow our detailed instructions.

1. Use a screwdriver to pry out the lamp clips.

Replacing the license plate light bulb Renault Sandero Stepway 2012

The video shows how backlight bulb license plate on a car Renault Sandero Stepway 2012.

Bulb replacement Renault Duster license plate light

Bulb w5w and a flathead screwdriver are all we need.

With a little effort, we wring out the lamp housing from the place of fixation.

Take it out carefully so as not to damage the plastic latches.

When dismantling the wiring block, it is necessary to hold it only by the body itself.

Press them carefully so as not to break them.

After the latches are removed, the diffuser can be easily removed.

The lamp from the place of fixation should be taken out carefully so as not to break the "antennae".

Assembly is carried out in the same manner as removal.

We do similar steps with another lamp in the same sequence.

When performing work with a screwdriver, be extra careful, as the latches on the lantern body are made of fragile plastic and, if they are carelessly exposed to it, they can simply break.

As you can see for yourself, there is nothing complicated in changing the number plate lamp for Renault Logan, just a little free time and following our instructions exactly.