Changes in O8 software:
1. Improvement: version 4 of function AF#13 (additional channel No. 1) and the operating algorithm of this function with the CAN module installed have been changed.
AF#13=1 - unlocking the trunk lock;
AF#13=2 - flexible programming;
AF#13=3 - hood lock control;
AF#13=4 - starter protective interlock.
If a CAN module is installed, then unlocking the trunk via CAN works with any setting of the AF#13 function. That is, the additional channel itself can be used for flexible programming, controlling the hood lock or blocking the starter.
2. Improvement: event “23” has been added to flexible programming - a command to unlock the trunk.
3. Improvement: option 4 of function SF#13 has been changed: SF#13=4 - “steering shaft lock control”.
This function is necessary to implement remote/automatic engine starting via CAN on Toyota vehicles.
4. Improvement: option 1 of function AF#20 (additional channel No. 6) has been changed: AF#20=1 - analog Webasto management.
The general control algorithm is similar to option AF#20=4, but during the entire operation of Webasto there is a “constant minus” at the output of the additional channel.
5. Improvement: Webasto operating algorithm has been changed for option SF#19=4: first Webasto launch, then (after the time in SF#18) - start the engine. When the engine starts, Webasto does not turn off, but continues to work together with the engine. Webasto turns off along with the engine at the end of the remote control, or when switching from the remote control to the key.
6. Improvement: added function AF#27 (additional channel No. 9):
AF#27=1 - control of light signals;
AF#27=2 - flexible programming;
AF#27=3 - imitation of the brake pedal;
AF#27=4 - DVR control.
Launching an additional channel via SMS/DTMF is carried out by command “89”.
7. The error that caused malfunction power output “blue wire” when CT is activated (in “start-stop” mode - with setting SF#8=3)
8. Improvement: when extending the operating time of the remote/automatic start of GSM/SMS with the “21” command, the indication on the LCD key fob display was not updated.
9. Improvement: function AF#15 (additional channel No. 3) has been changed:
AF#15=1: 1 second pulse 1 second after the engine stops;
AF#15=2: flexible programming;
AF#15=3: duplication of light signals;
AF#15=4: pulse control of light signals.

StarLine A93 Software O6

Software algorithms have been optimized. Instructions unchanged.

StarLine A93 Software O5

Changes in O5 software:
1. Changed option No. 1 of function SF#19: SF#19=1 - Webasto control with the button combination "1 (long) + 3" is disabled.
2. The logic of operation of option No. 2 of function AF#7 has been changed - “authorization during remote or automatic engine start (SLAVE enabled)”:
AF#7=2 - authorization when disarming, but without central locking control.
3. Correction: the serial number of the event “successful authorization in SLAVE mode” has been corrected; now this event corresponds to the “correct” number 22.
4. Correction: The error that led to a double number of light signal control pulses when selecting AF#15=3 and AF#15=4 has been fixed.
5. Bugfix: Fixed a bug that caused incorrect operation I-key functions (unsuccessful “key reading” at startup).
6. Improvement: imitation of door opening “via CAN” is now performed ONLY when security is on.

7. Correction: the error due to which additional channel No. 6 could not be controlled from the mobile application has been fixed (in the case when the flexible programming option is selected for the additional channel - AF20=2).

StarLine A93 Software O3

StarLine A93 and A63 Software N2

Changes in N2 software
New opportunities:

1. Added the ability to cancel an alarm with the first button of the key fob
2. The simulation of opening the door using additional channel No. 3 (AF#15=1, AF#15=2) has been returned when performing program neutral
3. Added “learning” algorithm for the “iKey” function (14 clicks service button+ ignition on)
4. The call function has been removed: the transceiver button duplicates the service button
5. Engine temperature control has been moved to the “status check” function (press button 3)
6. Brake pedal: security zone status returned
7. If the central unit is in security mode with sensor bypass (shock, tilt), then the GSM command “11” disables sensor bypass (sensors are activated)
8. Added a function for selecting “additional locking” of the central locking system after closing the trunk in security mode
9. SLAVE mode: the option to start the authorization procedure “by ignition” has been changed to “by ignition or transition from ignition support to normal mode”

Corrections:
Fixed a bug: when choosing the conditions SF#8=3 and SF#16=4, the algorithm of operation of the power “green” wire in some situations did not correspond to the declared one (SF#16=4 - duplication of the Starter signal).

StarLine A93 and A63 board GK54 M8 software

M8 Software Changes
New opportunities:

1. Changing the flexible programming algorithm: for settings db and dY

default changed to ON. dbON and dYON - control is not disabled.

2. Added support for R4 code relay.

StarLine A93 and A63 board GK54 software M5

Changes to M5 software
New opportunities:

1.Updating the function of additional locking of the central locking upon completion of the emergency (SF#7=3 &

SF#7=4): additional locking occurs both after successful startup and when

each unsuccessful attempt launch
2. Changing the flexible programming algorithm: for items db and dY, the default settings are changed to ON
3. Changing the program neutral algorithm: closing the trunk after

turning off the engine or turning on the security system does not cancel the program

neutral

StarLine A93 and A63 board GK54 M2 software

Changes to M2 software
New opportunities:

1. In flexible programming, the “successful authorization” event has been added - event No. 22;
2. Changing the program neutral algorithm (option SF#15=3): when the security system is turned on, the engine is switched off immediately;
3. SLAVE mode: the “analogue” status of the doors is delayed for 5 seconds (until the command to remove is received standard system from security);
4. SLAVE mode: added alarm stop function StarLine button"lock" of the standard key fob

StarLine A93 and A63 board GK54 software L8

Added support for iCAN engine blocking function. For work

function requires updating the software of 2CAN and CAN-LIN modules to version 3.4 and

StarLine A93 and A63 board GK54 software L7

Serial number AX3W...
All connectors on one side:

Changes in L7 software
New opportunities:

opening the trunk.

4. Improvement of starting algorithms: starter activation delay (in accordance with

function 10) will occur every time you try to start.

StarLine A93 and A63 board GK34 software L7
Universal systems with key fob from A93 (with engine start).
Serial number AX3W...
Connectors on both sides:

Changes in L7 software
New opportunities:

1. Improvement of the SLAVE mode: when you select to start the authorization procedure by “opening the doors,” the authorization will also start when you open the trunk.
2. Once the remote start is complete, the shock/tilt sensor will be delayed for 8 seconds.
3. For function 16 of Table 2 (operation algorithm of the “green” output of the power module), the “ACC” and “Starter” options have been added:
table 2 16=1 - ignition, 16=2 - accessories, 16=3 - ignition* (output is switched off during starter operation), 16=4 - starter
4. Improvement of starting algorithms: a delay in starting the starter (in accordance with function 10) will occur with each starting attempt.

StarLine A93 board GK24 software L7
Serial number A93W...
Connectors on both sides:

Changes in L7 software
New opportunities:

Improved SLAVE mode: when choosing to start the authorization procedure by

opening the trunk.
2. Once the remote start is complete, the shock/tilt sensor will be delayed for 8 seconds.
3. For function 16 of Table 2 (operation algorithm of the “green” output of the power module), the “ACC” and “Starter” options have been added:
table 2 16=1 - ignition, 16=2 - accessories, 16=3 - ignition* (output is switched off during starter operation), 16=4 - starter
4. Improvement of starting algorithms: starter activation delay (in

according to function 10) will occur on every attempt

StarLine A93 software version K9

StarLine A63 software version L2-L7

Changes in software L2-L7
New opportunities:

1. Improvement of the SLAVE mode: when choosing to start the authorization procedure by

opening the trunk.
2. Simultaneous reception of statuses is prohibited (via the 2CAN interface and analog inputs).
3. Improvement: when opening the trunk (in security mode), the central locking impulse now appears after closing the trunk.

StarLine A63 software version K9

StarLine a93 is a modern, new generation car alarm system that keeps your car safe for high level. The Starline A93 alarm system with auto start allows you to control the car remotely, which is very convenient. For example, in winter, you can turn on the interior heating in your car or start the engine to warm up without leaving your home. In summer you can also control the air conditioner remotely. The operating instructions for the key fob will show all the possibilities and tell you how to use the alarm correctly.

On this page of the site you can download the manual operation of StarLine a93 Can Lin. The manufacturer of Starline a93 GSM strongly recommends reading the user manual before use. Thanks to this, setting up the key fob will be easier, and you will be able to familiarize yourself with all functionality devices.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline!

A brief guide to using StarLine a93 ECO will help you set up the key fob step by step, get acquainted with the principle of its operation, and familiarize yourself with information on programming the device.

Proper use – maximum effect

The installation instructions are also available online, allowing you to read them without downloading. The instructions are what you need to read first. There are several reasons for this:

• After reading the user manual, you will not break the key fob trying to learn how it works on your own;
• You will learn the full functionality of StarLine a93;
• You will be able to competently use all the capabilities of the device;

The operating instructions are available for download and online viewing on our website completely free of charge. After reading the manual, you will learn how to configure options individually, be able to use car autostart, and learn how to receive car safety notifications on mobile phone and open up many more possibilities.

StarLine A93 2CAN+LIN price: 10,200 rub.

Price with installation: RUB 15,200.

• 3 year warranty!

List of vehicles supported via CAN protocol

Alarm Description

StarLine A93 2CAN+LIN is a new product from UltraStar, built using technology modular architecture, which is used in older models. Car alarm complete power module to connect automatic and remote engine starting, which will allow you to warm up the engine and car interior in advance in winter and cool it down in summer. StarLine A93 connects to digital buses all modern cars via the CAN protocol, as well as via LIN, which is important for installation in domestic cars: LADA Granta, Kalina, Kalina ll, Priora. In addition to the standard reading and control functions (door switches, central locking, full-time security, etc.), the module allows you to implement, on some cars, comfort functions, such as folding mirrors, closing windows and the sunroof.

Security and safety

The interactive authorization method with individual encryption keys, 128 bits long, makes intelligent hacking by code grabbers impossible.
Narrowband 128 channel transceiver copes well with radio interference in big city, providing control range up to 500 meters, and notification up to 2 km.
StarLine A93 is equipped with a built-in 3-axis accelerometer that responds to impact, movement, jacking or evacuation. In this case, setting the sensitivity of all sensors is available from the alarm key fob.

Remote and automatic engine start

Remote start carried out by command from a key fob or from a phone (GSM version). If the command is successfully completed, an indication of the running engine and the remaining operating time will appear on the key fob. As a rule, the warm-up time is set to 20 minutes, but if necessary, it can be extended at any time.

Auto start modes:

• by alarm (at a specified time)
• periodic (at a specified interval from 2 to 24 hours, in 2-hour increments)
• by temperature (when the temperature sensor registers a temperature below the set value from -3°С to -27°С, in increments of 3°С)

Keychains. Display and control

The new shock-resistant key fob has a fresh design and a pleasant white backlight of the LCD display. In addition to displaying information about the security status, lock status, active functions, battery voltage, etc., with its help you can configure security modes, autostart parameters and accelerometer sensitivity.


An additional key fob, without a display, is equal in cryptographic strength to the main one. To transmit control commands, both key fobs use a dialogue encryption algorithm that excludes intelligent electronic hacking. Also, an additional key fob functions as a “tag” when the system is operating in Slave mode.

SUPER SLAVE mode

In slave mode, turning the security mode on and off is carried out using a standard key fob (key or other method provided by the car manufacturer). At the same time, to disarm the device, you can install additional owner authorization using a tag (second key fob) or by entering a code on the standard buttons. This mode work is available and does not work correctly on all cars.

Modular architecture and its capabilities

The modular architecture of the central unit allows you to install a GSM module without additional wire connections. This will make it possible to monitor the condition of the car and control all the functionality of the system, without limiting the distance. Management is possible in several ways:

• a regular call to the SIM card number installed in the alarm and entering commands in tone mode
• using a convenient mobile application
• using a special Internet service

Installing a GPS/Glonass module will make it possible to track all vehicle movements, generate reports for a certain period about the route, mileage, speeding, leaving a geofence, etc.

Alarm characteristics

	DIALOG PROTECTION The StarLine dialog control code with individual 128-bit encryption keys guarantees reliable protection from all known code grabbers.
	RADIO INTERFERENCE PROTECTION StarLine operates confidently in conditions of extreme urban radio interference, thanks to a unique 128-channel transceiver.
	SUPER SLAVE Car security control using a standard key fob with reliable additional interactive authorization by any of the two StarLine key fobs. Option available when integrating 2CAN+LIN interface
	EXTENDED TEMPERATURE RANGE StarLine works confidently in harsh conditions climatic conditions at temperatures from minus 50 to plus 85 °C thanks to high-quality components.
	AUTHORIZATION BY PIN CODE Additional authorization reliably protects the car from theft, enhancing security functions standard alarm. A trip is possible only after entering an individual PIN code using the standard car buttons. The option is available when integrating a 2CAN+LIN interface.
	RECORD ENERGY ECONOMY StarLine guarantees the preservation of sufficient battery charge for up to 60 days in security mode through the use of patented technologies and software solutions.
	COMMUNICATION CHANNEL CONTROL Automatic control of the communication channel ensures that the key fob is within the range of the car alarm transceiver.
	3D SHOCK AND TILT SENSOR Integrated digital sensor shock and tilt with remote control registers jacking and evacuation of the vehicle.
	SMART KEYLESS BYPASS StarLine iKey allows you to implement keyless bypass standard immobilizer in cars equipped with security StarLine complexes. The option is available when integrating a 2CAN+LIN interface.
	INVISIBLE LOCK iCAN guarantees reliable protection thanks to a unique patented technology for hidden engine blocking via the car’s standard digital buses. The option is available when integrating a 2CAN+LIN interface.

	TELEMATICS (OPTIONAL) Integration of optional GSM-GPRS, GPS-GLONASS telematic interfaces allows you to remotely control the security of your car and carry out monitoring.
	CONTROL FROM PHONE (OPTIONAL) Integration of an optional GSM interface allows you to manage security and service functions, receive security status alerts on your mobile phone.
	FREE MONITORING (OPTIONAL) With the help of simple and convenient monitoring www.starline-online.ru you can find out the location of your car with an accuracy of several meters. The option is available when you connect GPS-GLONASS-Master and have an optional GSM interface.
	AUTO START Intelligent autostart allows remote and automatic start engine temperature, at a given time or periodically.
	2CAN+LIN Integration of the optional 2CAN+LIN interface provides fast, convenient and safe installation StarLine security equipment for modern cars equipped CAN buses or LIN
	FLEXIBLE SERVICE CHANNELS Programmable parameters for controlling hazard lights, folding mirrors, customizing seats for the owner and much more.
	IMPACT RESISTANT KEY RING The StarLine key fob has an innovative, shock-resistant design, ergonomic design and an internal protected antenna.

Equipment:

• central alarm unit;
• 1 key fob with two-way communication with LCD;
• 1 key fob with two-way communication without LCD;
• transceiver;
• hood button;
• Light-emitting diode;
• service button;
• set of wires;
• engine temperature sensor;
• installation instructions;
• user manual;
• user manual;
• blocking relay with block.

Specifications:

• Carrier frequency of radio control signals from 433.05 to 434.79 MHz;
• Number of radio control channels 128;
• Maximum range of the main key fob when transmitting control commands
• 800 m;
• Maximum range of the main key fob when receiving alerts
• 2000 m;
• The maximum range of the additional key fob is 15 m;
• Shock/tilt sensor type: integrated three-axis accelerometer;
• Operating temperature from -50 to +850С;
• Supply voltage direct current 9 - 18 V;
• The current consumed by the alarm in security mode is no more than 26 mA.

Car alarm Starline A93 2CAN+2Lin on the 4th generation platform replaced the A91 Dialog model. Unlike older modifications (StarLine A94, D94 and other models), this development has a built-in relay that allows you to reliably control the car lock, as well as the light signal.

Starline A93 2CAN+Lin stands out with a new, more ergonomic key fob with a liquid crystal display, with a beautiful white backlight, in a shock-proof case. Thanks to the use of new service channels, the development allows for easy installation of additional modules without the use of external components.

Advantages and features of the A93 2CAN+2Lin device

The main unit of the A93 is quite miniature, built according to a modular concept. It means that Starline installation A93 2CAN+2Lin is justified at least by the fact that, if desired, you can access it without special labor connect GSM and GPRS modules, units of GPS and GLONASS systems, expanding its functionality to the level of a professional security telematics complex. At the same time, the owner of the device has the choice to use only those features that come with the standard package.

WITH additional modules StarLine A93 car alarm can be controlled remotely via mobile app on a smartphone. Carry out free monitoring of your car's location via satellites from anywhere in the world. 2Can and 2Lin adapters make it possible to install Starline a93 on almost any car that is equipped with a CAN or LIN bus, and this is more than three hundred car models. These include the entire latest line of cars from the Volga Automobile Plant (Kalina, Kalina II, Priora, Granta).

The SUPER SLAVE function allows you to control vehicle functions using a standard key fob, as well as an additional one, with securely implemented interactive authorization. The key fob itself will inform the car owner with a buzzer signal that he has left the communication zone with the car. The Starline A93 2CAN+2Lin alarm system is connected to it via one of 128 secure radio channels. Conversational code and individual encryption for each device are an insurmountable wall against code grabbers. By the way, the developers promise a multi-million dollar reward to anyone who can hack this protection.

They also guarantee flawless and stable operation of Starline A93 in cities where the airwaves are very noisy. The device operates in a temperature range from -50°C to +85°C and has low power consumption. The car can remain in security mode for 2 months, maintaining sufficient battery charge to start the car. A 3D sensor will detect the fact that the car is being towed or jacked up.

Car alarm Starline A93 2CAN+2Lin buy possible in our company, this will be the right and reasonable decision for most car owners.

Articles and news about StarLine A93 2CAN+2LIN

30.08.2018

The offer is intended for careful drivers whose cars are equipped smart alarms. Insurance companies highly value the protection against theft of StarLine security solutions, and can also reduce rates for drivers with careful driving (without sudden acceleration, braking and lane changes). Information about management style Insurance Company receives from accelerometer telematics alarm system StarLine. Currently, Incor Insurance Insurance Company and R-Telematica are participating in the project.

20.06.2018

New version of StarLine software No. 4.7

Came out a new version Firmware for Starline anti-theft systems No. 4.7. The update adds support for 18 cars from 2008 to 2018, expands the list of cars for keyless auto start, and also improves the system operation algorithm on some cars.

All functions of StarLine A93 2CAN+2LIN

2CAN+LIN interface
Using a 2CAN+LIN interface allows you to correctly integrate the StarLine A93 2CAN+2LIN anti-theft system into electronics modern car with minimal interference with standard wiring.

Remote engine start
The intelligent autostart function allows you to start the car engine at the owner’s command or at a specified event (time, temperature, etc.).

Customizable service channels
Customizable service channels allow you to configure the operation of light alarms, control folding mirrors, adjust seats, etc.

Shockproof keychain
Innovative anti-theft control key fob StarLine system A93 2CAN+2LIN has an ergonomic, shockproof design and a secure built-in antenna.

StarLine iKey technology allows you to implement the auto-start function by bypassing the standard immobilizer without using duplicate car keys or expensive imported modules. List of supported vehicles.

For management anti-theft system StarLine A93 2CAN+2LIN uses 128-bit dialog code encryption of radio signals with individual keys. This provides unrivaled protection against all known types of code grabbers.

A unique 128-channel transceiver guarantees stable operation of the car alarm radio channel even in conditions of strong interference in large cities.

As an additional line of protection in StarLine A93 2CAN+2LIN, you can use PIN code authorization. Only after entering secret code You can start your trip using the car’s standard buttons.

To record all types of physical impact on the car, the system is equipped with an integrated 3D shock, tilt and movement sensor. The sensor also detects jacking and attempts to evacuate the car.

Slave mode StarLine works A93 2CAN+2LIN allows you to control security from the car’s standard key fobs or KeyLess system without manipulation of the key fobs of the anti-theft system. StarLine interactive authorization is used as an additional line of defense.

StraLine's iCAN interlock can be used as an additional line of defense. The patented technology allows you to make engine blocking invisible to scanners using the standard digital tires of the car.

Thanks to the constant monitoring of the connection between the key fob and the anti-theft system, the car owner will be immediately notified when leaving the coverage area of ​​the StarLine A93 2CAN+2LIN transceiver.

Thanks to high-quality components, StarLine A93 2CAN+2LIN remains fully operational even in extreme temperatures from minus 50 degrees to plus 85 degrees Celsius.

Equipment StarLine A93 2CAN+2LIN

• Keychain with LCD screen
• Keychain without feedback
• Siren S-20.3
• Service button
• Central unit with integrated 2CAN+2LIN interface
• Transceiver (transceiver)
• Light-emitting diode
• Start module with temperature sensor
• Set of wires and installation materials
• Set of printed materials