01 November 2016 Reliability, the range in the city from the key fob to the car is only 1000 m. Secretive, reliable, with a high operating range.

Vladislav Zakhmatov

02 November 2016 All of them are in question, except the range. Or the installers' hands are growing in the wrong place. Does not understand via digital channel (CAN bus) Subaru Outback 2007 Can't duplicate the key and start the car Pandora CLONE ( This f-i stated on the website). Doesn’t see the doors by numbers, doesn’t understand the temperature of the engine, interior and outside. Very sensitive buttons on the key fob, I have disarmed it in my pocket more than once.

Pasha Apostol

November 16, 2016 Recently we installed this alarm on the Lada Vesta, but for some reason the key fob does not correctly display the temperature, voltage and fuel level in the tank for some reason 0, maybe it’s a crude firmware?

Marat Burganov

November 22, 2016 I called 65-90-30 and they announced the price for a DX50B alarm system with installation at 16,000 rubles. As soon as I started signing up for installation, the price suddenly increased to 19,000 rubles, the manager referred to the fact that this was the recommended price for installation. According to the site for enticement, the price with installation is generally 13,620 rubles. Not Seriously, first say one thing and then say another.

Vladimir Delyusto

November 26, 2016 All in the comments All in the comments At my request, they installed an alarm system, Pandora DX 50b, on the FF3 2012 Trend configuration, that is, with a standard remote key, the car does not have a standard alarm system. For information, I’ll tell you that on another machine I have Pandora Pandect x-2050. After installation, some questions arose. 1. The battery voltage on the key fob does not correspond to reality, we tried to calibrate it as expected (programming mode, check), but religion does not allow us to charge the battery to 12 V - it’s 12.7 according to the tester, but on the key fob it’s 12.0 - 11.9 and, by the way, it changes strangely both when the car is turned off and when the car is running (this is not the case on the x-2050, I had to calibrate it). Is there really no other algorithm for adjusting this value, other than connecting a constant stabilized power source instead of a battery for this very adjustment. 2. When starting, the check on the key fob shows, in addition to the incorrect voltage, the remaining fuel in the tank (87%, without calibration, approximately the same as the real one in the tank) the readings of the interior sensor (it’s lying, because it’s located on the right under the glove compartment, it’s warmer there, plus probably than they wrapped something like electrical tape - somewhere around 5 - 7 degrees), readings from the engine temperature sensor, upon receiving the car I saw the location on the stove PIPE and asked (calmly asked) to twist the sensor with its ear onto the block, secured it to a bracket between the block and valve cover. It seems to show more accurately (+1 C to real t), but on the block itself it would be preferable. The last parameter, this is the reading of the external temperature, there’s an ambush here, it shows the number 107. It was probably 107 degrees on the street, but no, it was -2 C. What kind of number is this?! 3. When setting the alarm, only the Pandora DX 50b key fob works, the standard key fob is not active - the buttons do not work. At the same time, it does not blink alarm(again the same rake as on the x-2050). When disarmed with the Pandora key fob, the emergency lights also do not blink, the siren works in both cases, but with the standard key fob you CAN DISARM the alarm, and when disarmed with the standard key fob, the emergency lights blink as expected. If you try to disarm the alarm with the key (open the door with a mechanical key), then DISARMING occurs, the signal goes to the key fob. That is, by turning the cylinder, you can easily get into the car, the alarm will NOT work. 4. The keychain itself is beautifully illuminated, but done sparingly: LEDs, 4 pcs. only from above, the uneven distribution of lighting is obvious. The buttons are very sensitive, it is easy to accidentally disarm. The security LED is quite bright and directional. It itself is in a small stand, so it cannot be placed in the air duct. Via CAN it shows in real time the opening of each door, it works quickly, you don’t have to wait for anything, as with many other alarms. 5. Autostart works, but the DX 50b does not support Clone FF3, and this was stated on the manufacturer’s website on 07/31/2016. Also, most of the programmers are inexpensive, they don’t flash 80bit chips (on FF3 this is the case), so for autostart I had to REMOVE the chip from the spare key, which is not good. I haven’t checked the range yet, I set the time on the key fob, auto start at t=-12, alert when leaving the reception area. I was pleased with the leather (not made from young dermantine leather, but leather) case.

Evgeniy Vilkin

09 February 2017 Supports autostart on Peugeout 4007 without bystanders, keys in the car, etc. bad decisions. Long range keychain. The alarm may be technically advanced, but from an ergonomic point of view it is absolutely terrible. 1. Even the alarm LED shows that Pandora is installed on the car. Because of large sizes It is impossible to install an LED “beautifully”. 2. The “new” key fob is terrible with its tiny buttons with invisible icons on it. 3. The keychain is terrible with its beeping, I got it literally in one day. Silent mode is inconvenient, just let it beep less! 4. Why can’t you turn on autostart if the car is not armed? 5. Why can’t you arm the car with the same regular button if the car is running and with the key in the ignition? It is necessary! I always considered myself not very pretentious. I've used regular Starlines all my life. But Pandora simply upset me with its lack of thought in normal use.

Anton Dubkov

February 28, 2017 Keyless crawler for Lada Vesta, dialog code Inconvenient to use There are several annoying things that make me unable to recommend this alarm - Small buttons - Remote start takes a very long time to work (about 20-30 seconds) - if I left the apartment and started the “process” at the entrance, then it starts only when I had already approached the car. - If during the remote start, or immediately after it (!), you press the “open” button, the car will stall. Everything would be fine, but even after the key fob signaled that the car had started, you still had to wait a few seconds before opening the car, otherwise it would stall. I constantly fall for this bullshit. - On the mechanics - if you open the car, put it in program neutral - it is reset. It is not possible to disable this unnecessary protection. Switch to "automatic" mode??? - Illogical operation of the “ignition support mode”, namely: When setting to program neutral, when you remove the key from the ignition, the engine continues to work (everything is fine with this). Next, if you press the “close” button, the engine will be turned off. But if you suddenly “changed your mind” and decided to arm the car while it was running, this stupid alarm system will not allow you to do this! You had to think about this in advance BEFORE pulling out the key (for some reason), and press some button until 2 peaks (you’ll remember what button it is). In theory, everything should be much simpler: it should be possible to either arm with the engine running (one combination of buttons), or arm and turn off (another), regardless of how the key was pulled out and what was pressed or not pressed before. - Opening the trunk to closed car, launched from autorun, does not work! You must first open the car, then the trunk opens. And even when the car is turned off, the trunk does not always open (with the key fob), sometimes you have to “modify” it with the standard key fob. In short, damn it's 2017, I didn't know it was so bad

The Pandora DX50 car alarm belongs to the category of premium anti-theft systems and is a digital security system with an auto-start function.

In addition to the integrated CAN streaming module, this “signaling” is equipped with a breakable LIN controller with support for LIN buses.

[Hide]

The Pandora DX50 alarm system is the development of Russian engineers. Its design incorporates the latest software and hardware solutions. The model has a two-way communication option that allows you to monitor the condition of the vehicle remotely, according to the readings of the key fob.

Pandora DX50 has:

• long service life;
• increased level of reliability;
• high quality, recognized by world experts.

Specifications

The main properties of the Pandora DX50 signaling device:

1. Availability of digital CAN interface. This allows you to install a security system by connecting to the appropriate connector. Interference with staff work on-board network will be minimal.
2. Possibility of device control pre-heating power unit. This refers to cars with diesel engines.
3. Using a communication channel control system through which data is transmitted between the microprocessor unit and the transceiver.
4. Monitoring the situation inside the vehicle. For this purpose, sensitivity, motion and tilt sensors are used. The first two are designed to determine physical impacts on the body and activity inside the car. The tilt controller allows you to learn about the movement of the vehicle, for example, on a tow truck, or about its jacking.
5. The presence of dialog signal encoding, which is used to protect packet data during transmission.
6. Using a USB connector on the module. With its help, a car enthusiast can connect to the alarm system via a computer and thus configure the basic parameters of the system.
7. The operating range of the remote control when operating in the command sending mode will be about 300-900 meters, depending on the terrain. If the communicator is used to receive messages from an alarm system, its range of action can be up to 2.2 km.

Testing the operating range of the Pandora DX50 car alarm is shown in the video by Dmitry Timofeev.

The operating range of the Pandora DX50 key fob depends on several factors, including the charge of the battery in the remote control and the presence of buildings in the area.

Equipment

The Pandora DX50 package includes the following components:

1. Anti-theft system control unit. Used to receive, process and transmit commands to actuators and the remote control. The module is based on an ARM controller from the manufacturer ST-microelectronics.
2. The main communicator for alarm management. It is equipped with a screen and has a notification function, which simplifies its use in general.
3. Protective case for the main key fob.
4. Spare remote control. The device does not have a display, its operating range is significantly lower compared to the main pager.
5. Set of power cables for connection.
6. Guarantee.
7. LED to indicate a vehicle with installed alarm. This model uses a three-color LED lighting source. The indicator is equipped with a cable with a connection block.
8. Login button emergency mode Valet.
9. Wire for connecting a digital interface.
10. Fastening kit for fixing the main alarm components.
11. Service manual. The manual indicates all the nuances of installation and initial setup. anti-theft system.
12. Relay block for implementing the engine autostart function.
13. Temperature sensor.

Distinctive parameters of dx50 and dx50b

Pandora line 50 anti-theft systems are developed based on the same technologies and solutions. The main differences are in the configuration, but they are not significant. DX50b models come with a redesigned main communicator.

Pandora DX-50 B, initially has low price, allows the car owner to save money, since there is no need to give away one of the standard keys or order a duplicate. The new LCD key fob D-078 is similar in appearance to its predecessor, but has a black body and is more economical and has a more informative screen.

New in the DX-50 B LCD:

• separate door indications are displayed, as on the flagship Pandora models;
• there is a work icon preheater;
• a convenient system of widgets that help you quickly assess the current state of the car and alarm system.

Keychain Pandora DX-50 B

How to install?

Installation process:

1. Before self-installation It is recommended to open the delivery package and connect all elements to the control unit.
2. The module is then connected to battery. This will make sure that the alarm is working or whether there are problems in the functioning of the alarm system.
3. After connecting, you do not need to bind the key fob, you just need to check the operation of the security mode.

Connection diagrams

Electrical diagrams for installation and connection of elements are shown in the photo:

Description of the keys of the main and additional Pandora DX50 remote controls

Designation of buttons and icons on the key fob

List of indicators on the device display:

1. Symbol for sending commands.
2. Indicator of the current connection status to the central node.
3. Another icon defining the connection with the control unit. For car alarms equipped with GSM modules.
4. GPS receiver indicator. The symbol lights up when the device is activated and the coordinates of the vehicle are determined. If the indicator is blinking, location calculation is not possible.
5. Alarm protection mode status icon.
6. Activation of security mode.
7. Door lock security indicator.
8. Remaining fuel icon in the gas tank.
9. Symbol security zone hood
10. Indicator of running power unit.
11. Icon of a protective zone powered by a motion controller.
12. Battery voltage symbol.
13. Temperature indicator for the power unit, interior and air.
14. Current time indication.
15. Work symbol lighting fixtures car.
16. Element of the protective zone of the luggage compartment.
17. Engine blocker.
18. Indication of battery charge in the communicator.
19. Standard alarm icon.
20. Parking brake symbol.
21. The ignition element that determines the functioning of this security zone.
22. Sensitivity controller operation indicator.
23. Silent security mode is enabled.
24. Preheater action icon.
25. Alarm setting indicator.
26. Symbol for using timer channels.
27. The option for silent operation of the communicator is enabled.
28. Indicator for requesting the current alarm status, as well as entering the event menu.
29. Feature enabled Maintenance security complex.

Designation of icons on the screen of the Pandora DX50 remote control

Setup and programming

In accordance with the instructions for use, binding of new key fobs is carried out as follows:

1. The first level of alarm settings is entered, and the communicators are programmed sequentially.
2. Three buttons are pressed on the key fob body. They must be held in this state for 1 second until the remote control emits a melodic signal. After this, the keys are released. If a second communicator is programmed, the LED indicator on it turns off.
3. When paired correctly, the remote control plays a double signal and the siren sounds anti-theft complex. You can program the next device, but the interval between settings should be no more than 20 seconds. To record tag keys, similar steps are performed.
4. To exit the binding menu, press the Valet emergency mode button. The alarm LED will blink red and green.
5. Then you need to turn the ignition on and off.

Security functions

Features of controlling anti-theft options DX50 Pandora.

Key number	Description of functions
1	Used to activate the protection mode, pressed when the ignition is turned off. At the same time they trigger lighting devices And . The communicator plays a melody, and an indicator in the form of a closed lock appears on its screen. If you need to turn on the security mode without sound signals, then held for two seconds. Activation of the “Search” function for a car in a parking lot is performed by briefly pressing vehicle must be protected at this moment.
2	Disable protection. The headlights and siren will blink twice. An open lock indicator will appear on the remote control screen. If the protection is turned off without sound signals, then the second button must be held for two seconds.
3	Used to remotely open the tailgate. Regardless of whether the security mode is on or not, the button is held down for several seconds. If the protection is activated, then when the trunk door is opened, the shock sensor and additional controllers will be deactivated, but all other areas of the car are protected. If luggage compartment was not opened within 15 seconds after the command, its lock will automatically close.
1 and 2	Locking the doors when the ignition is on is done by pressing the first button, opening - the second. The Pandora DX50 alarm system is configured by default to lock the doors after starting the engine, this happens after 5 seconds. To activate the “Panic” mode, the buttons are pressed simultaneously. A similar combination is used to disable the function.
1 and 3	Activation of the protective function in the “Busy Hands” mode is performed by simultaneously pressing the first and third keys. 30 seconds after the “click” door locks will close and security will be turned on.

Arming the Pandora DX-50 B alarm system Disarming the Pandora DX-50 B alarm system

About setting up basic options security system using a communicator in the video was described by user Andrey Popov.

Setting up alerts

The Pandora DX50 alarm system provides several options for warning the car owner that he is leaving the communication zone with the control unit.

To configure one of the methods, you will need:

1. Go to the programming menu.
2. Move the cursor to the position of the “RFM” icon using the third key.
3. Press and hold the first button for one second.

Short presses select the warning option:

After selecting an option, press the first button. If you need to leave the binding menu without saving, then hold down the third key for one second.

Programming

The third button on the communicator will help you change the current time:

1. The cursor on the screen must be moved to the position of the indicator in the form of an alarm clock.
2. The first button changes the hours, and the second button changes the minutes.
3. Once assigned, the third key is pressed for a few seconds.
4. Automatic exit from the binding menu will occur after 10 seconds;

Setting up timer channels used to control additional equipment is done by moving the cursor to the “CH” indicator. Using the third key, you select the desired channel.

To enter the alarm settings menu, use button 3 to move the cursor to the position of the indicator labeled “Setup”. Then the first key must be pressed for 1 second. Button 3 is used to move from one sublevel to another.

Changing the service PIN code

The password can be changed as follows:

1. The security mode is turned off, the ignition in the car must also be deactivated.
2. The emergency mode key is used to enter the password. Factory setting code - 1111.
3. You need to press the Valet button several times, the number of “clicks” corresponds to the first digit of the password. The pause between each press should be no more than 1 second. If the character is entered correctly, the alarm indicator light will blink red.
4. The next three digits are entered in the same way. After each character is indicated, the red indicator should light up
5. If the password is entered correctly, diode light bulb will flash green and red. The procedure for assigning a new code should be carried out after 5 seconds.
6. The Jack button is pressed twice. If you have entered the password change menu, the siren will sound twice.
7. Using the Valet key, you enter the first digit of the code; the number of presses must correspond to it. Each time you press the VALET button, the status indicator lights up orange.
8. Pauses between clicks should not exceed 1 second. When the system confirms reception of the first digit of the code with a red flash of the status indicator, the remaining three characters are entered in the same way. This will be followed by a series of red and green status indicator lights. This means that the fourth digit has been received.
9. Finally, you will need to enter the code again.
10. If inserted successfully, the system will emit a series of red and green flashes, after which new code will be recorded, the key fob will return to programming mode.
11. If the code is entered incorrectly the second time, the status indicator will turn red.

Remote control of controllers

Sensor configuration features:

1. The sensitivity is changed by entering the menu and moving the third button of the cursor to the indicator in the form of a hammer hitting the body. Then hold down the first button for one second.
2. Key 3 changes the sensitivity level of the warning and alarm zone. To increase and decrease parameters, use buttons 1 and 2, respectively.
3. To switch between alarm and warning zone indicators, press the third key.
4. After setting the values, the first button is pressed for one second.

Autorun

Rules for controlling remote engine start:

1. The first button is pressed and held for three seconds. As confirmation, a corresponding indicator will appear on the remote control display. After a few seconds, the power unit will start.
2. To stop the engine started by command, you need to hold down the second button of the communicator for two seconds.

User Dmitry Titov as an example Kia car showed how the option works automatic start engine.

Download free installation and operating instructions in PDF format

You can download service manuals for the use and installation of alarms using the following links:

Advantages and disadvantages

Benefits specific to the DX50 Pandora:

• simultaneous protection of more than 10 vehicle zones is ensured through the use of highly sensitive controllers;
• big temperature Range for the use of a security complex, the anti-theft system, according to owner reviews, can operate without interruption at -50 degrees;
• auto engine start;
• the presence of a “Turbo timer” option - the function will ensure gradual cooling of the turbocharged power unit, which significantly extends its service life;
• the ability to connect the anti-theft system to the car’s digital interface;
• the use of secure communication channels, thereby minimizing the likelihood of signal interception;
• quick determination of any physical influences on the body, as well as all moments associated with the movement of the vehicle;
• the presence of a highly intelligent information processing system, due to which the likelihood of false positives is minimized;
• ease of use of the communicator is ensured by the housing, as well as the small size of the device;
• monoblock control module in which the main controllers are installed, which greatly simplifies the process of installing the anti-theft system;
• Availability detailed diagram connections are included, so that the connection of alarm elements can be carried out by the car owner without the involvement of specialists.

The main disadvantage of the security complex is high cost. At this price, you can find more functional alarms from other manufacturers on the market. Car owners also note that over time, malfunctions may appear in the operation of the control unit. To eliminate them you need to either set new module, or change its firmware.

What is the price?

Approximate cost of purchasing an alarm system:

Video

The Autokasta channel presented real review user about the operation of the Pandora DX50 car alarm, as well as recommendations for choosing an anti-theft system.

The Pandora DX-50 system is a digital security system with an auto-start function. It is equipped with an integrated CAN streaming module that supports all cars on the market in our country. The system is also equipped with a breakable LIN controller with support for LIN buses of UAZ, Lada, BMW, Datsun cars and pre-heaters Webasto and Eberspacher.

The signaling uses a narrowband radio path at 434 MHz with channel control and feedback for a new LCD key fob in a stylish housing gray; The package also includes an additional R305L key fob without an LCD display. The built-in installation will greatly simplify installation and save owners money. keyless crawler for cars Toyota, Lexus, Honda, Acura, Hyundai, Kia, Renault, Lada, Nissan and Mitsubishi.

IN Pandora DX-50 There is a shock/motion/tilt sensor, including one that provides protection for the car's wheels. The system is designed for operation in the conditions of our country, therefore temperature regime work starts from −50 degrees.

The monoblock form factor of the base unit, which already includes an RF module, allows you to significantly save installation time, because There is no need to install the RF module separately.

Features of the Pandora DX 50 car alarm

Double-sided key fob with LCD display

• Switching the security mode on and off using different buttons.
• Automatic control of the radio coverage area of ​​the notification channel.
• Monitoring the status of 10 independent security zones.
• View the 10 most recent events by time and event.
• Built-in vibration alert.
• Indication of battery discharge level.
• Quick remote adjustment of the sensitivity of the built-in motion sensor.
• 16 sound alert melodies.
• Quick remote adjustment of the sensitivity of the built-in shock sensor.
• LED backlight LCD display.
• Indication of the current time, alarm clock.
• Indication of engine temperature and interior temperature, battery voltage.
• Confirmation of button presses with vibration notification.
• Synchronization of the key fob and base unit clocks, exact time in the history of events.
• Key fob battery AAA (1.5 V).

Base unit

• Updating the system software from the manufacturer’s website using the built-in micro-USB port.
• Conversational encoding of commands at 868 MHz.
• Maintaining a log of events in the base unit with recording of the event and the exact time during the period of lack of communication with the key fob with LCD for subsequent transmission to the key fob.
• Personal encryption key 128-bit long, can be changed by the user.
• Built-in integral accelerometer for motion and shock recognition with adaptive processing algorithms and sensitivity adjustment from the key fob.
• Possibility of using single-wire digital blocking relay BM-103/105.
• Separate hood and trunk sensor inputs.
• On-board network voltage monitoring.
• High-precision measurement of engine and interior temperatures, indication on the key fob display.
• An improved method for polling sensors that eliminates false alarms.
• Automatic arming.
• Two-step door unlocking.
• Taking into account the delay of interior lighting when arming.
• Security mode with engine running.

Protected areas of the car
The Pandora DX-50 car alarm protects the following independent zones by issuing a corresponding notification to the key fob and recording in the synchronous event protocol of the base unit:

• critical drop in power supply voltage of the vehicle's on-board network
• car door perimeter
• Tilt sensor triggered
• hood limit switches
• motion sensor triggered
• trunk limit switches
• turning on the ignition
• triggering of the built-in shock sensor (alarm level)
• pressing the brake pedal

A two-way key fob is the main means of managing and monitoring the state of the system.

The key fob uses flashing LED indicators “SEND” and “ALARM”, which increase the information content of the key fob.

To facilitate the perception of events, the key fob uses 16 melodies. Each melody corresponds to a separate event.

Equipment:

• Base unit
• Main remote control with LCD display
• Optional remote control key fob (without LCD display)
• Main cable
• Cable with three-color LED status indicator
• Cable with VALET button
• LIN interface wire
• Mounting kit
• Operation and installation manual
• Relay trigger module
• Engine temperature sensor
• Package

Car alarm "Pandora DX50" is one of the most high-tech security and service systems belonging to the premium category and installed on cars of any class. The only requirement and limitation for the installation of this system is the vehicle’s on-board voltage of 12 V. The Pandora DX50 alarm system is a development of domestic engineers, which was created on Kaluga plant experimental instrument making. Highly qualified and experienced domestic engineers were able to connect in this alarm latest developments in the field of engineering and modern software and hardware solutions.

To develop the Pandora alarm system, we used Hi-tech from global manufacturers of security systems and electronic components. High precision and reliable equipment, used for monitoring and installation of systems, gave the alarm such characteristics as long term operation, high level of reliability and high quality, recognized by world experts.

Functional Features

IN official review The manufacturer of the Pandora DX50 said that this model of the security system replaced the proven Pandora LX 3257. This model became famous thanks to unsurpassed reliability and the maximum distance of the notification channel. The new model not only retained the advantages and characteristics of its predecessor, but also introduced innovative functions, while the manufacturer offered an affordable and attractive price for the security system.

Reviews about the Pandora DX50 complex confirm its wide functionality and ability to support digital car interfaces not only foreign brands, but also domestic ones, the connection to which is carried out via LIN. Such versatility guarantees high demand for the complex, while the functionality can satisfy the most demanding customers.

Car alarm keychain

Set car alarm includes a key fob with a liquid crystal display that notifies the owner of a violation of any of the ten available security zones. The security system settings can be changed using the key fob; its functionality allows you to save the last ten events and view data from temperature sensors.

Innovative technologies for comfort and safety

Users leave good reviews about the Pandora DX50 system; they confirm the presence of the function. Thanks to this option, you can start the car by pressing one key on the key fob. The function is especially convenient in the cold season, when you have to wait a long time for the car to warm up, which is not very comfortable and unsafe. For cars with turbocharged engines, a security system model with a turbo timer is provided.

A distinctive feature of the Pandora system is the built-in three-coordinate accelerometer, operating in the main three axes. The car owner is notified in real time about any impacts on the vehicle: impacts on the body, evacuation, jacking, rocking.

Signaling benefits

Users, as already mentioned, leave reviews about the Pandora DX50 complex in a positive way; they note the following advantages:

• Ten independent security zones.
• Ergonomic and compact body.
• Engine autostart and turbo timer options.
• CAN/LIN bus that allows you to install the "Pandora DX50" as on modern models foreign cars and domestic cars.
• Communication channel with high level protection and frequency 868 MHz.
• Built-in immobilizer bypass, which is an excellent option for owners of cars such as KIA, Nissan, Toyota, Lexus, Honda, and other foreign cars.
• Wide operating temperature range - the security complex can be operated at temperatures of -50 degrees Celsius.
• The number of wires and connecting elements is minimal, which simplifies the installation of the system.
• High precision vehicle tilt and movement sensors.
• Accessible and intuitive Russified interface.

Autostart

The functionality of the security system includes options for automatic and remote engine start. It is most relevant in cold or hot seasons and allows you to save free time on warming up the car interior in winter or cooling it in summer. Implement remote start possible via a key fob with a liquid crystal display. With it you can program autorun. Several engine starting modes are available:

• Scheduled.
• Every day at the set time.
• Upon reaching a certain battery charge level.
• At set intervals.

The system also has a turbo timer function.

Compactness of the complex

The layout of the security complex is monoblock. The main signaling module and the radio part, equipped with an 868 MHz antenna, are located in a compact central unit. Concealment of components and saving of space for placing the system are ensured due to the absence of an external wire antenna. On the body of the main unit there is a quick programming key and a micro-USB port, with which you can configure the system in detail.

False alarms of the security system are completely eliminated thanks to the digital tilt/shock/motion sensor with adaptive processing and the radio blocking relay on the Pandora DX50. The accelerometer functions and protects against tilt, impact and movement even when the car engine is running. The sensitivity of the sensor decreases only while the starter is operating. Each time the car alarm is turned on, the initial angle of the car’s position is recorded: even if it is parked at an angle, the complex will work and notify the owner.

Remote start

The car engine starts only after the built-in immobilizer recognizes the standard key. Autostart is possible only if the immobilizer is bypassed or the vehicle is imitated standard key inside the car. Alarm Trade company in its security complexes offers two options for solving this problem.

Pandora Clone - imitation of a standard key

The Pandora DX50 car alarm is connected via a CAN bus, which reads the signal produced by the standard key and stores it. When starting remotely and giving the appropriate signal to start the engine, the system simulates the signal from the standard key, which is received by the immobilizer and allows you to start the car engine.

Keyless way to bypass the immobilizer

Integrated into the electrical system via the LIN bus. When a command to start the engine is received, the standard immobilizer is turned off by the alarm, after which a signal is sent directly to the ECU to allow starting.

Both of these options eliminate the need to manufacture chips, use additional equipment or the presence of a standard key in the car interior to implement autostart.

Reviews about the Pandora DX50 system note that this function is not implemented on all vehicle models.

Main characteristics of the alarm

• Turbo timer.
• Automatic engine start.
• Integrated adaptive motion/shock/tilt sensor.
• Support digital buses LIN/CAN
• Supports performance at low temperatures.
• Protecting your car from wheel removal and theft.
• Protection against false positives.
• Ten independent protected areas.

Car alarm equipment

• The main block of the system.
• Keychain with liquid crystal display.
• Additional key fob with three keys without display.
• Case for key rings.
• Main cable for connection.
• Cable with VALET key.
• Cable equipped with a three-color LED status indicator.
• Mounting kit.
• LIN interface wires.
• Instructions for "Pandora DX50" and instruction manual.
• Package.
• Temperature sensor.
• Relay trigger module.

The Pandora DX50 alarm system, the price of which is around 40 thousand rubles, is one of the most affordable and attractive security systems on the market.

Pandora DX 50B price: 9,480 rub.

Price with installation: RUB 14,480.

*Implementation of autostart from 2,500 rubles.

• Equipment warranty 3 years!
• Lifetime warranty on work!

Alarm description

Pandora DX-50B is the successor to the popular security system. It is absolutely resistant to code grabbers. The use of one of the best integrated transceivers ensured the highest range of the warning channel.

The developers managed to put many basic and useful functions, maintaining a low cost. For example, the DX-50 supports digital interfaces CAN modern vehicles, can be connected via LIN to Lada cars, Datsun, BMW, UAZ. Can control pre-launch Webasto heaters and Eberspaecher, which eliminates the purchase of additional expensive controllers.

Autostart

The alarm system has the ability to remotely and automatically start the engine. This function is useful in hot or cold weather. It will help save time on warming up the engine and interior in winter. In summer, it will ensure comfortable entry into the car with the help of air conditioning. Independent remote start is carried out using a key fob with an LCD display. Autostart is programmed by him. The user has various options for starting the engine:

• Scheduled;
• at the same time every day;
• at a certain interval;
• upon reaching the battery charge level.

The turbo timer function is also supported.

Keychain

Includes keychain with LCD display. It will notify the user of alarms in 10 independent security zones. It can be used to configure some parameters of the DX-50, for example, starting or stopping the engine, preheater. Autostart function and installed heater will allow you to warm up the engine before starting it. Using the key fob, you can view the readings of temperature sensors and the history of the latest important events, battery voltage, information about the security status, and more.

System compactness

The system has a monoblock layout. The miniature central unit houses both the basic signaling module and the radio part with an 868 MHz antenna. The absence of an external wired antenna will save installation space and ensure the concealment of components. On the body of the unit there is a quick programming button and a micro-USB port for detailed settings.

Built-in digital sensor shock/tilt/motion has adaptive processing, which eliminates false alarms. The accelerometer protects against shock, tilt, movement and running engine. The sensitivity of the sensor is automatically reduced only while the starter is operating. The DX-50 protects against wheel theft. The starting angle is calibrated each time the system is armed. Even if the car is parked at an angle, the system will work flawlessly.

Pandora Keyless Remote Start

Every time you start the engine, the immobilizer in the car queries the standard key and only after the key is recognized, the engine starts. To implement the autostart function, you need to bypass the immobilizer or simulate the presence of the key in the cabin. Alarm Trade alarms offer two options for solving the problem.

Pandora Clone. Imitation of a standard key.

The alarm is connected via CAN bus, reads a signal that reproduces the standard key and remembers it. IN right moment, when a command is given to start the engine without a driver in the cabin, the system simulates a key signal, the immobilizer accepts it and allows the engine to start.

Keyless immobilizer bypass.

Integration into the vehicle's electrical system is carried out via the LIN bus. When commanded to start the engine, the alarm turns off standard immobilizer and sends a signal allowing start directly to the ECU.

Both options exclude the use additional devices, manufacturing chips and finding a standard key in the car interior to implement autostart.

The functions may not be available on all vehicles.

Main characteristics

• Autostart;
• Turbo timer;
• Built-in adaptive shock/tilt/motion sensor;
• Support for CAN/LIN digital buses;
• Work at temperatures up to - 50C;
• Wheel theft protection;
• 10 independent security zones;
• Protection against false positives.

Equipment

• Base unit;
• Main key fob with LCD display;
• Keychain case;
• Additional key fob (without LCD display);
• Main cable;
• Cable with three-color LED status indicator;
• Cable with “VALET” button;
• LIN interface wire;
• Fastening kit;
• Operation and installation manual;
• Relay trigger module;
• Engine temperature sensor;
• Package.