How to change front wheel bearing hyundai ix35. Club Hyundai ix55 - Hyundai Veracruz

When operating a car chassis bears the bulk of the mechanical load. One of its elements is the hub, a part involved in the transmission of torque to the wheels. The free rotation of this part provides wheel bearing: his technical condition has a direct impact on vehicle handling. When the bearing is worn timely replacement avoids emergencies and the risk of deformation of the entire node .

Replacing the bearing of the front hub / rear hub: symptoms of a malfunction

By what signs can you understand that it's time to change the front wheel bearings? There are several obvious "signals" that indicate problems with this part:

Wheel play. To check this, you can call in a car service or put the car on a jack yourself and see if the wheel plays when you shake it up and down. Reliability of fixing of a wheel means that the bearing is not worn out;
Hub heating . Similar problem takes place when in the bearing of the front or rear hub there is no lubrication, and it is clogged with dirt;
Uniform rumble of the wheel when driving, which increases with increasing speed;
Vibration. Such a “symptom” is characteristic of many breakdowns, so it should be considered only in combination with other signs.

If you notice one or more of these signs, then your car needs to replace the rear wheel bearing and front wheel. You can make a replacement in "Autoclub 8" - a modern service center providing impeccable quality works. You can find out how much it costs to replace a hub bearing on a Hyundai ix35 in our car service on our website in the "Prices" section.

Brands of cars serviced in our car service

Cars of the following brands: Mazda (Mazda), Nissan (Nissan), Infiniti (Infiniti), Mitsubishi (Mitsubishi), Ford (Ford) .

Indicative list of work when replacing a wheel bearing

During the replacement process, our specialists will carry out the following types of work:

dismantling the wheel and pads;
remove the caliper and the entire assembly, including ball joints;
removal of a worn bearing, cleaning the groove of the part from used grease and other contaminants;
mounting new part and installation in the reverse order of the rotary mechanism, pads and wheels;
adjustment, checking the performance of the node.

car hub- the basic component of the wheel rotation mechanism, connected to braking system. The hub is fixed on the axle (shaft) and attached to the rim (spokes). Its main element is a bearing, consisting of a housing, rollers, outer and inner rings and a separator. The bearing provides an efficient connection of the hub with the axle, representing the main part of the chassis of the car. Despite the fact that this component is protected by anthers, its lubrication loses its properties over time, which leads to deterioration in rotational parameters and failure of the part.

Prices for replacement services depend on the make and model of the car and can vary significantly in different car services.

Replacing the rear hub bearing on the Hyundai ix35: signs of a malfunction

By what signs can you understand that the degree of wear is close to critical and you need to replace the rear hub bearing? Specialists of the capital's car service "Autoclub 8" recommend seeking help if you notice:

Noise while driving. When moving, the wheels begin to emit a uniform rumble. As the speed increases, it increases, and as it decreases, it weakens. Such a sound is typical when the bearing is dirty, when there is no longer any lubricant left in it;
vibration. It makes sense to consider this sign only in combination with all other “symptoms”, since vibration during movement can have a variety of causes;
Heat. Increased friction in the absence of lubrication in the bearing leads to heating of the hub;
Wheel play. To check the reliability of fixing the wheel on the hub, it is enough to raise the car with a jack and check the wheels for play by shaking it up and down.

Brands of cars serviced in our car service

Our center in Moscow performs maintenance of cars of such brands as Ford (Ford), Mazda (Mazda), (Mitsubishi), Nissan (Nissan), Mitsubishi and Infiniti (Infiniti).

Prices for rear wheel bearing replacement services

impact loads, difficult conditions operation reduce the working life of the bearing, and over time, the question of its replacement arises. Check out the offers of the company "Autoclub 8": we offer affordable price for rear wheel bearing replacement, prompt diagnostics, quality service and a guarantee for all types of work.

The content of the article:

Before replacing the hub Hyundai bearing ix 35 make sure to diagnose to determine which bearing needs to be replaced.

Up. Hyundai ix 35 LeichtPanzerKampfwagen › Logbook › Replacing the front support bearings and front left wheel bearing.

It is interesting! The Hyundai logo is not just the letter "H" in aval. It would be too easy. This emblem symbolizes the handshake of two people - a representative of the concern and satisfied customer. In addition, translated from Korean, the word "hyundai" is translated as "modern".

Car service "Auto-Mig" > Hyundai repair > Bearing replacement Hyundai hubs IX removal of the front hub assembly. Pressing out the broken wheel bearing and pressing in the new one.

The nearest streets to the entrance are Marshal Biryuzov, Berzarin, People's Militia, Sorge, Kuusinen, Raspletin .. I drive and enjoy the silence in the suspension. Loosen the two nuts securing the shoe guide and rounded fist.. Polevaya Sabirovskaya, 37, from 9 to 21, t. Also, after the frost, a rumble with a slight beating began to appear from the front left.

Club Hyundai ix55 - Hyundai Veracruz - Wheel bearing replacement

AngelBlack and Hyundai ix35 LeichtPanzerKampfwagen before: Toyota Auris and Mitsubishi Lancer. When replacing brake discs sentenced front oprnyye bearings. When scrolling, the crunch was concrete. How was this not noticed in the OD when diagnosing the suspension? Most likely not diagnosed at all. Support took the original R After the holidays signed up for a replacement. There is no point in describing the process.

Only the masters were again surprised at the thickness of the reinforced springs .. Also, after the frost, a rumble with a slight beating began to appear from the front left. As a result, the front left wheel bearing was sentenced. I read on the forums that SKF and ILJIN mainly go to the conveyor. I took SKF BAHA, it seems like the quality is better. ILJIN stood at the opening. After replacement, everything is good. I go and enjoy the silence in the suspension.

In the front suspension, a separate replacement of the hub bearing is possible. And on rear suspension this bearing is changed only in assembly with the hub itself. Accordingly, in the first case, the spare part itself is cheaper, but the work of replacing it is quite laborious. And in the second case, the hub assembly for the Hyundai iX 35 is more expensive, but it is easier to replace it.

Work order

Technology for replacing the front hub in a Hyundai ah35 car:

the car is lifted up
the wheel is unscrewed
removed stopping support
remove brake disc
unscrew the steering knuckle assembly with the hub
the hub is pressed out of the steering knuckle

Then assembly is carried out in reverse order. Replacing the rear hub is done in the same way.

Replacing the front hub bearing

To replace the front hub bearing on the Hyundai ix35, the hub itself is first dismantled using the technology described above. Then, with special narrow-ended pliers, the wheel bearing retaining ring is compressed and removed from the groove of the steering knuckle.

After that, the hub is pressed out of the inner ring of the bearing and the bearing itself is removed from the steering knuckle. Seat surfaces are treated against rust and lubricated grease. Then new bearing must be pressed into the hole of the steering knuckle of the car.

For all types of work on the replacement and repair of hubs and bearings in the network of our car services, a guarantee is provided. Hubs and bearings of original and non-original production are available. we will provide you great quality works and competitively low prices.

We are under renovation Hyundai car i30 (Hyundai 30), which will need to replace the front wheel bearing. We will show you how to do this operation yourself and how to diagnose bad bearing hubs.

On this machine, the front left wheel bearing howled, before proceeding with its replacement, it is necessary to diagnose it and make sure that it is because of it that unpleasant sound. To do this, you can jack up the front of the car and set the wheels of the car in motion. They will spin freely and the car will stand still, so you can hear exactly where the sound is coming from.

We proceed to the replacement, dismantle the wheels, take out the cotter pin. With a 32 head, unscrew the axle shaft nut:

If you don't have a gun, then when unscrewing, use a long knob and insert a strong screwdriver into the disc vent. Then we unclench the pads together:

And we unscrew the caliper bracket, it is fastened with two 14 bolts. ABS sensor it is bolted to the steering knuckle, bolt 10.

Loosen fixing screws brake disc, they are under a Phillips screwdriver:

Set the disk aside. We take out the cotter pin from the steering tip and unscrew its fastening nut, it is 17. After that, we remove the tip from the cordon, this can be done, as in our case, using two hammers:

Or using a special puller. Since this car has a faulty ball joint, we will unscrew it from the bipod and take it out along with the fist, since it is going to be replaced, if this were not the case, then it would be necessary to unscrew the bipod from the lever. The ball nut is 17. We unscrew the shock absorber bolts:

Now you can get the steering knuckle together with the hub. Through a suitable mandrel, we knock out the hub from the steering knuckle:

In our case, the inner race of the wheel bearing remained pressed onto the hub. It can be cut with a grinder, we will use a more civilized way and knock it down with a chisel:

FROM reverse side we need to remove the retaining ring, for this, at the beginning we knock it out with a hammer and a screwdriver, then we take it out with the help of round-nose pliers: