Let's show you how to Kia car Ceed 2011 onwards replace the rear brake pads, discs and caliper guides. We remove the wheel, unscrew the caliper (bolts 14), take it to the side. We remove the brake pads. We remove the bracket using a 14 head and a spanner wrench. After that, we check the guides, in our case, one walks normally, and the other does not, replacement is necessary.

The brake discs have a special window:

There is a mechanism for bringing and diluting the pads, the so-called spacer bar. In order to bring the pads together, we take a good strong screwdriver, twist down with clinging movements, to the end. The next step, we will need an impact screwdriver to unscrew the fastening screws:

Using a hammer, remove the brake disc. Often brake discs turn sour on the hub, so be sure to lubricate all "landing" surfaces before installation copper grease so that next time you can take it off without any problems.

Videos rear replacement brake discs and pads in KIA Ceed:

Backup video how to replace rear brake discs and pads in Kia Sid:

The brake disc on this machine acts as the "drum" for the parking brake.

Check the condition of the brake pads at every service.

Brake pads must be replaced when the linings are worn out (the minimum allowable thickness of the friction linings is 2.0 mm), when the linings are not firmly connected to the base, when the working surfaces are oily, if there are deep grooves or chips.

On inner pads rear brakes wear indicators installed. Upon reaching the minimum allowable thickness of the pads, the wear indicator contacts the brake disc during braking, causing a squeak, signaling the onset of the wear limit of the brake pads.

WARNING

Replace rear brake pads only as a set of 4. (two on each side). Before replacing brake pads, check the level brake fluid in the main tank brake cylinder. If the level is close to the upper mark, it is necessary to pump out part of the liquid, since after replacing the worn pads with new ones, the level will rise.

You will need: 14 wrench, flat blade screwdriver.

1. Remove the rear wheel.

2. Turn out a bolt of the bottom directing finger...

3. . .and lift the caliper up together with the outer brake shoe.

4. Remove the outer and inner brake pads from the guide.

USEFUL ADVICE

Every time the brake pads are replaced in without fail check the condition of the protective rubber covers guide pins, as well as the ease of movement of the caliper relative to the guide of the brake pads. If movement is difficult, lubricate grease guide pin and its cover.

5. Using sliding pliers, push down the cylinder piston.

6. Install retaining springs, brake shoes and other removed parts in the reverse order of removal.

7. Replace the brake pads in the same way brake mechanism right wheel.

8. Check up and if necessary restore level of a brake liquid in a tank of the main brake cylinder.

19.07.2018

Brake pads for any car are consumable They need to be replaced as they wear out. Usually a quality part goes up to 50,000 km. Understand that it's time to change, you can visual inspection, or at the signal of the wear sensor - a characteristic screech of metal will be heard. We can help you find the right parts for Kia Ceed, we will tell you how to replace them yourself.

Kia Ceed SW 2013 (station wagon)

Choice of pads for LED ED, JD

TRW GDB3585, 3582 are suitable for JD, they go about 50-60 thousand km, while they do not crumble, they do not eat the disk. The price is about 2000 rubles. You can purchase an analogue of REMSA, which is produced by the same plant. The price is on average 500 rubles lower. original part is distinguished by the SBK marking and is produced in South Korea, in quality it is not much different from analogues, but the price is usually higher. Original pads for cars 2006-2012 (ED) have the following article numbers:

581011HA00 - on cars from 2006 to 2009, after that another article went to the same cars - 581011HA10, in fact the details are the same;
Also used item 583021HA00 and 583021HA10 (rear);
For hand brake - 583501HA00.

For cars after restyling, pads with other codes are provided. However, they are all the same size, so the parts can be considered interchangeable.

The block on the left obviously needs to be replaced, the block on the right is new

CEED A2 has been produced since 2012 and has the following part numbers:

58101A6A00 - until 2013;
58101A6A01 - produced from 2014 and later;
58101A2A25 are used for those configurations that are equipped with 300 mm brake discs.

For cars manufactured in 2015-2017, the following pads are suitable:

58101A6A02 - for models that have been restyled since 2016.
58101A6A70 - for cars with 300 mm discs.

The rear pads have the following article:

58302A2A30 if hand brake mechanical.
58302A6A20 - for complete sets with EPB.

If the car is of an old generation, but with R16 wheels and 300 mm discs, the article will be different.

We remind you that there are cases when cars of the same series, year of manufacture and configuration have different parts that differ significantly from each other. Therefore, for exact selection Auto Parts is best to use the VIN number of the machine.

Self-replacement process

You can also replace the pads with your own hands: it is not difficult if you have certain skills. On the Kia Sid, the hydraulic cylinder is unpaired, with the exception of the sports modification - two cylinders per wheel are placed on such a machine. The cylinder is needed in order to act on the inner pad, press it against the disc, and the outer one is pressed by itself. The pads wear out more on the outside, but both need to be changed, and on one axle at once, regardless of the wear on the pads on the second wheel. In addition, you should know that the rear pads go on average one and a half times longer than the front ones, since braking usually occurs first with the front wheels.

Removing the front wheel

When installing pads, keep in mind that the wear sensor must be on inside. The degree of wear still needs to be checked periodically, sometimes the sensors break off. When replacing pads, they must not be lubricated, even if they are installed with great difficulty. A lubricated part will not work, and the brakes can fail at the most inopportune moment.

Before starting work, it is necessary to measure the level of the brake fluid. It is poured into a special tank, which is located under the hood of the car. Make sure that the liquid is not above the mark, the excess will have to be drained. This will be required because after you put in new pads, the fluid level will rise slightly. In addition, you need to check how the caliper moves, which guides the block. If it moves with difficulty, the guide pins need to be lubricated.

Unscrew the two screws reverse side brake caliper

The work is as follows:

In order to get to the pads, the wheel will need to be removed;
The caliper must be raised up;
You will need a 12 wrench, with which you need to unscrew the bolt located on the bottom of the bracket body. In this case, it is advisable to hold the guide finger with a hexagon;
After that, you will need to remove the guide pads, first the inner one, then the one located outside;
Remove the springs from the guide;
The assembly takes place in the reverse order, first of all, fixing springs are installed, then caliper guides. They can be unscrewed, so an anaerobic fixative is applied to the threads for reliability;
The brake fluid must be checked again, topped up or removed if necessary.

Remove the caliper and old front pads

The procedure for replacing the parking brake pads, rear and front wheels kia Sid. Subtleties and nuances self replacement pads Kia seed.

Replacing the brake pads Kia Sid

On the Kia cars Sid, like most non-sporty cars, has only one hydraulic brake cylinder for each wheel. Oil change in automatic transmission KIA SID 2007 Replacement Nissan Bluebird rear brake pads photo report If you own a sports car, there may be two of them located on both sides of the disc. The task of the cylinder is to create pressure on the inner pad, while the outer one is pressed by force, since its structural design is such that there is no other place left. Due to the fact that the main work falls on the inner pad, its wear is traditionally stronger compared to the outer one.

With that in mind, don't be surprised if the outer pad is much less worn. kia seed replacement lamps fog lamp video Replacing the rear brake pads Ford Fusion It is also important to know that pad life is rear wheels ah is traditionally 1.5-2 times larger than the front ones, which withstand the main load during braking. Relatively uniform wear can only be observed when your driving style approaches "retirement". However, in this case, the brake pads will serve you not 30, but all 60, or even 70 thousand kilometers. Kia led fog light bulb replacement 2013 Sirius Avto To install the pads correctly, remember that the wear sensor (the so-called "peep") is installed only on the inner pad, since it wears out faster. Replacement rear pads and brake discs Lancer 9 Mitsubishi. Master Cylinder Replacement kia clutch Sid - Kia Ceed But remember that there are times when such sensors simply break off without having time to inform the car owner about pad wear. Rear brake replacement pads and brake drum Kia Spectra. Replacement rear brake pads on Mitsubishi car Lancer IX is the same for all 3 types of engine, and therefore the catalog below. Do not rely on it, and check the degree of wear of the brake pads yourself, during seasonal maintenance, for example.

First of all, let's designate the safety rules when examining the condition of the brake pads:

Always check their condition at the passage of each MOT. Also check with the experts if the replacement of the Kia Sid handbrake pads is required
Do not use friction linings with a thickness of two or less millimeters, but rather replace them before this dangerous milestone
Replace the Kia Sid pads if you see chipping, deep grooves, a large oily layer or a weak connection between the pads and their base on their surface.
All KIA Sid brake pads are equipped with wear indicators, which, when the pads are thinned to an acceptable minimum, begin to touch the brake disc during braking, which leads to a clearly audible squeak. If you hear such a sharp creak, replace the brake pads immediately, otherwise any of your trips may turn into a serious accident.
Replace brake pads exclusively in a comprehensive manner. Choice Replacement oils in a box automatic KIA so, for example, install 4 pieces on the front brakes at once - 2 per wheel
Before starting to replace the pads, measure the level of brake fluid in the reservoir of the main brake cylinder. Replacement rear Volvo xc60 brake pads 2013 + - If its level is near the top mark, then drain it a little, because always after installing new pads, its level will increase
Don't forget to check the movement of the caliper along the brake shoe guide. Do-it-yourself replacement of Kia Ceed bulbs If it is difficult to move, lubricate its guide pins with grease.

Replacing the rear brake pads KIA SID / Kia Ceed / Lubrication of the calipers

This video was edited in YouTube Video Editor ()

Replacing the rear brake pads KIA RIO 2013 in detail and clearly

In this video I'll show you how replace rear brake pads! Everything is very simple and fast. No need to pay uncles...

Kia See'd front pad replacement procedure

Disassemble the front wheel
Raise the caliper up
Using a 12mm wrench, remove the lower caliper housing bolt. Replacing the front and rear brake pads on the Skoda Octavia A5 To facilitate this procedure, hold the caliper guide pin with a hex wrench
Remove the brake pads from the guide - inner and outer
Remove a pair of fixing springs from the shoe guide
Reinstall the brake pad guides with retaining springs, and then all other parts. News Kia Sid Fog Lamp Bulb Replacement Video Kia Sid Replacement fan nozzle windshield washer - To prevent the caliper finger guides from self-unscrewing during operation, an anaerobic fixative should be applied to its thread in advance
Check the brake fluid level and top up if necessary.

The procedure for replacing the rear pads "KIA Sid"

Disassemble the rear wheel
Then you should remove a pair of brake pads from the guide - inner and outer
Use sliding pliers to sink the piston of the cylinder
Using a 14 wrench, unscrew the lower bolt that secures the caliper. To better perform this procedure, lift it through the top bolt
Pull out the old pads, but before installing new ones, thoroughly clean the guides.
And only after that, in reverse order, install the brake pads with fixing springs and all other parts.
Finally, don't forget to check the brake fluid level in the reservoir and top up if the level is low.

Brake replacement pads Kia Sid is over, but do not rush to immediately go somewhere in your car, especially since you do not need to go to busy city streets and high-speed country roads. Replacing the rear pads and brake discs Lancer 9. There is a possibility that during the first hard braking, the new brake pads will work with very little efficiency, even if you have installed branded rather than analog parts. After all, not only pads wear out, but also brake discs. And it happens that the new brake pads only come into contact with the edges of the old, already worn-out brake discs. Change air filter BMW X5 E70, E53, F15 If the car became more sluggish on the go, lost power and there is a feeling that the engine is "choking", mainly the problem lies in the deterioration of the property by another decrease in the volume of air entering it. Avoiding such an obstacle is quite easy - for this purpose, you sometimes need to ...