On Kia LED cars, as on most of the machines are not a sporty plan, only one brake hydraulic cylinder is provided for each wheel. If you own a sports modification car, there may be two, located on both sides of the disk. The task of the cylinder is the creation of pressure on the inner block, the clamp of the external occurs in a compulsory manner, since its structural device is such that the other place remains. Due to the fact that the main work falls on the inner block, its wear is traditionally stronger, in comparison with the external one.

Given this, do not be surprised if the external shoe turned out to be much less worn. It is also important to know that the service life of the pads on the rear wheels is traditionally 1.5-2 times more than the front, which maintain the bulk of the braking. Relatively uniform wear may be observed only when your driving style approaches the "pension". However, in this case, the brake pads will serve you not 30, but all 60, or even 70 thousand kilometers. To install the pads correctly, remember that the wear sensor (so-called "Piskun") is installed only on the inner block, since its wear is faster. But remember that there are cases when such sensors simply are laid out, not having time to inform the owner of the car to wear the pad. Do not hope for it, and check the degree of wear of the brake pads yourself, when passing the seasonal, for example.

First of all, we denote the safety rules when examining the state of the brake pads:

Their status is always checked when each pass is passed. Also specify from specialists if the replacement of the Kia LED handler pads
Do not use friction overlays with a thickness of two or less millimeters, and better replace them before the onset of this dangerous turn
Make a replacement of Kia LED pads if you see on their surface of the rocks, deep grooves, a large oily layer or a weak connection of linings with their base
All brake pads "KIA LED" are equipped with wear indicators, which during thinning pads to a permissible minimum begin to touch the brake disc during braking, which causes a distinctly audible screen. If you heard such a sharp creak - immediately replace the brake pads, otherwise any of your travel can turn into a serious accident
Replace the brake pads solely comprehensively. For example, install 4 pieces at the front brakes - 2 on the wheel
Before starting the replacement of the pads, measure the level of the brake fluid, filled into the tank of the main brake cylinder. If its level is located near the top mark, then it takes it a little, because it is always after installing new pads its level will increase
Do not forget to check the movement of the caliper along the guide brake pad. With difficulty moving, lubricate its guide to the fingers with a consistent lubricant.

Procedure for replacing the front pads Kia See'd

Log in front wheel
Caliper Lift up
Using the key to 12, unscrew the bottom bolt of the body of the bracket. To facilitate this procedure, the drive finger of the brackets hold the hex key
Remove the brake pads from the guide - inner and outdoor
Remove a pair of fixing springs from the guide pads
Set in reverse order guides brake pads with fixing springs, and then all other parts. So that the guide of the finger of the caliper is not self-energized during operation, an anaerobic retainer should be applied in advance to its thread.
Check the level of the brake fluid and restore its number if required.

The procedure for replacing the rear shoe "Kia LED"

Log in rear wheel
Then it should be removed from the guide of a pair of brake pads - internal and outdoor
Sliding Pastern Podopit Cylinder Piston
The key to 14 unscrew the lower bolt, which fixes the caliper. To better execute this procedure, lift it through the top bolt
Pull up old pads, but before installing new, clean the guides thoroughly
And only after that, in the reverse order, install the brake pads with fixing springs and all the other items
Finally, do not forget to check the level of brake fluid in the tank and add it if its level is insufficient.

Replacing brake pads Kia LED is over, but do not rush to immediately go somewhere in his car, especially since you do not need to travel to the lively urban streets and high-speed country tracks. There is a chance that when the first sharp braking, new brake pads will work with very low efficiency, even if you installed branded, and not analog items. After all, not only blocks are wearing, but also brake discs. And it happens that new brake pads only in the edges come into contact with the old, already sacrifted brake discs.

Therefore, to avoid such an unpleasant incident, choose some silent place and several times on it smoothly slow down the car. It is necessary that the pads go to the brake discs with the whole surface, and you were able to evaluate how effectively new blocks are inhibited.

And in the future, at least the first hundred kilometers passed to avoid sharp braking. The fact is that with strong heating of the pads, which have not yet been taken to brake discs, it can burn the top layer with their lining, with the result that new brake pads will not be able to demonstrate your maximum efficiency for a long time.

Check the state of the brake pads each time.

The brake pads need to be replaced with the wear of the lining (the minimum permissible thickness of the friction linings 2.0 mm), with a fraction of the lining with the base, grinding the working surfaces, the presence of deep furrows or chips.

On the inner pads of the rear brakes installed wear indicators. Upon reaching the minimally permissible thickness of the lining, the wear indicator during braking in contact with the brake disc, causing a creaking signal, signing on the onset of marginal wear of the brake pads.

A WARNING

Replace the brake pads of the rear brake mechanisms only with a set of 4 pcs. (two each way). Before replacing the brake pads, check the level of the brake fluid in the tank of the main brake cylinder. If the level is close to the upper label, it is necessary to pump out part of the fluid, since after replacing the worn pads, the new level will rise.

You will need: key "on 14", a screwdriver with a flat blade.

1. Remove the rear wheel.

2. Remove the bolt of the lower guide finger ...

3.. . And lift the caliper up along with the outer brake block.

4. Remove the outer and inner brake pads from the guide.

HELPFUL ADVICE

With each replacement of the brake pads, it is mandatory to check the condition of protective rubber covering covers of the guide fingers, as well as the ease of moving the caliper with respect to the guide brake pads. If moving is difficult, lubricate the guide finger and its cover.

5. Using sliding passages, climb the cylinder piston.

6. Install fixing springs, brake pads and other details taken in order to remove.

7. Similarly, replace the brake shoes of the brake mechanism of the right wheel.

8. Check and, if necessary, restore the level of the brake fluid in the tank of the main brake cylinder.

The procedure for replacing the brake pads of the handbrake, rear and front wheels Kia LED. Subtleties and nuances of self-replacement Kia Ceed pads.

Caia LED Brake Shoe Replacement

On Kia LED cars, as on most of the machines are not a sporty plan, only one brake hydraulic cylinder is provided for each wheel. Replacing the oil into the automatic transmission of KIA SIR 2007. Replacement The rear brake pads are Nisan Bluebird Photo report If you are owned by a sports modification car, there may be two of them located on both sides of the disk. The task of the cylinder is the creation of pressure on the inner block, the clamp of the external occurs in a compulsory manner, since its structural device is such that the other place remains. Due to the fact that the main work falls on the inner block, its wear is traditionally stronger, in comparison with the external one.

Given this, do not be surprised if the external shoe turned out to be much less worn. Kia Sid. replacement Fog lights Lamps Video Replacing the rear brake pads Ford Fusion is also important to know that the service life of the pads on the rear wheels is traditionally 1.5-2 times more than the front, which maintain the main load during braking. Relatively uniform wear may be observed only when your driving style approaches the "pension". However, in this case, the brake pads will serve you not 30, but all 60, or even 70 thousand kilometers. Caia LED Fog Lamps Replacement 2013 Sirius Avto To install pads correctly, remember that the wear sensor (so-called "Piskun") is installed only on the inner block, since its wear is faster. Replacing the rear pads and brake discs Lancer 9 Mitsubishi. Replacing the main clutch cylinder Kia LED - Kia Ceed But remember that there are cases when such sensors simply are laid out, not having time to inform the owner of the car wear. Replacing the rear brakes plodes And the brake drum Kia Spectra. Replacement rear The brake pads on the Mitsubishi Lancer IX car is the same for all 3 types of engine, so the capable below are catalog. Do not hope for it, and check the degree of wear of the brake pads yourself, when passing the seasonal, for example.

First of all, we denote the safety rules when examining the state of the brake pads:

Their status is always checked when each pass is passed. Also specify from specialists if the replacement of the Kia LED handler pads
Do not use friction overlays with a thickness of two or less millimeters, and better replace them before the onset of this dangerous turn
Make a replacement of Kia LED pads if you see on their surface of the rocks, deep grooves, a large oily layer or a weak connection of linings with their base
All brake pads "KIA LED" are equipped with wear indicators, which during thinning pads to a permissible minimum begin to touch the brake disc during braking, which causes a distinctly audible screen. If you heard such a sharp creak - immediately replace the brake pads, otherwise any of your travel can turn into a serious accident
Replace the brake pads solely comprehensively. Choice Replacement oils in a box of Kia LED automatic machine so, for example, on the front brakes, install 4 pieces at once - 2 on the wheel
Before starting the replacement of the pads, measure the level of the brake fluid, filled into the tank of the main brake cylinder. Replacement rear Brake Pad Volvo XC60 2013 + - if its level is near the top mark, then it takes it a little, because it is always after installing new pads it will increase its level
Do not forget to check the movement of the caliper along the guide brake pad. Replacing the KIA LED lamps (Kia Ceed) with their own hands with difficulty moving, lubricate its guide to the apparent lubricant.

Replacing the rear brake pads KIA LED / KIA CEED / Lubrication of Suports

This video is processed in the Youtube () video editor

Replacing the rear brake pads Kia Rio 2013 in detail and clearly

In this video I will show how replace rear Brakes pads! Very simple and fast. No need to pay unuse ...

Procedure for replacing the front pads Kia See'd

Log in front wheel
Caliper Lift up
Using the key to 12, unscrew the bottom bolt of the body of the bracket. Replacing the front and rear brake pads on Skoda Octavia A5 to facilitate this procedure, the drive finger of the bracket hold the hex key
Remove the brake pads from the guide - inner and outdoor
Remove a pair of fixing springs from the guide pads
Set in reverse order guides brake pads with fixing springs, and then all other parts. LED Qia LED Cea LED Replacing LED Family LED Lamp Replacement Firemen Replacement Fiberglass Waste - In order for the finger guides to the caliper is not self-energized during operation, an anaerobic retainer should be applied in advance on its thread.
Check the level of the brake fluid and restore its number if required.

The procedure for replacing the rear shoe "Kia LED"

Log in rear wheel
Then it should be removed from the guide of a pair of brake pads - internal and outdoor
Sliding Pastern Podopit Cylinder Piston
The key to 14 unscrew the lower bolt, which fixes the caliper. To better execute this procedure, lift it through the top bolt
Pull up old pads, but before installing new, clean the guides thoroughly
And only after that, in the reverse order, install the brake pads with fixing springs and all the other items
Finally, do not forget to check the level of brake fluid in the tank and add it if its level is insufficient.

Brake replacement plodes Kia LED is over, but do not hurry to immediately go somewhere in his car, especially, you do not need to leave for lively urban streets and high-speed country tracks. Replacing the rear pads and brake discs Lancer 9. There is a chance that with the first sharp braking, new brake pads will work with very low efficiency, even if you installed branded, and not analog items. After all, not only blocks are wearing, but also brake discs. And it happens that new brake pads only in the edges come into contact with the old, already sacrifted brake discs. Changing the BMW X5 E70, E53, F15 air filter if the car has become more sluggish on the go, the power has lost and there is a feeling that the engine is "suffocating", mainly, the incompleteness lies in the deterioration of the property for another decrease in the amount of air incurred. Avoid such a drainage is quite easy - for this purpose you are at times ...

Let's show both with your own hands in the Kia Ceed 2011 car. Replace rear brake pads, discs and guide calips. Remove the wheel, unscrew the caliper (bolts for 14), we assign it to the side. Remove brake pads. We remove the bracket with the head on the 14 and the cape. After that, we check the guides, in our case one goes normally, and the other is not necessary to replace.

There are special windows in brake discs:

There is a mechanism of information and breeding pads, so call the spacer plank. In order to reduce the blocks, take a good strong scolder, turn down clinging movements, to the end. The next step we will need a shock screwdriver to unscrew the mounting screws:

Using the hammer, remove the brake disc. Very often, the brake discs are sealed on the hub, so before installing, it is necessary to lubricate all the "landing" surface with copper lubricant so that the next time you could remove it without any problems.

Video Replacing the rear brake discs and pads in Kia Ceed:

Backup videos How to replace the rear brake discs and pads in Kia LED:

The brake disc on this machine serves as a "drum" for the parking brake.

Hello everyone. We produce the procedure for replacing the rear brake pads Kia LED. The pads on Kia Ceed are changing when the thickness of the friction pad is less than 2 mm. There are also cases when friction linings come off from the body of the pads. As a rule, an extraneous noise is heard with the limit wear of the pad. At first suspicions, do not hide the pads.

I advise when replacing the pads to look at the state of the brake discs. The minimum thickness of the brake disc 8.4 mm. On the eye, disperse the disk on six parts and make a measurement of thickness in each section. Thickness should not fluctuate, the difference is a maximum of 0.01 mm.

Step-by-step substitution

1. Remove the wheel.

2. Horn key on fourteen turning over the top bolt of caliper braces.

3. After unscrewing the bolt, raise the bracket upwards.

4. Remove old pads.

5. We inspect the guide calipers:

check the dustners of the gap
watch there is a lubricant
check the smoothness of movement

6. Adaptation Ichip the brake piston. The device is very simple. At the heart of the threaded screw of about 20 cm and a metal plate.

Remove the end of the screw into the piston and sum up on the thread so that the metal plate is overlapped into the body of the caliper bracket. Next, tighten and thereby set the brake piston. I would like to note, while pressing the piston, look at the level of fluid in the tank. Reflection if necessary.