The car door slammed, but the key remained in the cabin. The situation is extremely unpleasant, but completely solvable even with improvised means. Our review contains 4 life hacks that will allow you to avoid calling special services and open the car yourself.

Method 1: Using Shoelaces

If car lock protrudes upward above the door panel, then you can use the most ordinary shoe laces to open the car door.

Step 1. Make a tightening loop in the middle of the lace.

Step 2. Place the cord through the top corner of the door, pulling it back and forth and gradually lowering it down.

Step 3. Lower the hinge onto the door lock button.

Step 4. Tighten the loop around the button and pull the lace up to open the lock.

Method 2: Using a metal hanger

This method works on both vertical and horizontal locks on older cars. In the case of a car with an electrical package, it is better not to use it, since the wires can be damaged.

Step 1. Unbend a metal hanger or just a wire. There should be a hook at the end.

Step 2. Insert the hook between the rubber seal and the glass and push it inside.

Step 3. Hook the door rod that leads from the lock to the button.

Step 4. Pull the wire with the hook up and unlock the door.

Method 3: Using an inflatable blood pressure cuff

Opening a locked door using this method has minimal chance of damaging or scratching the car.

Step 1. Use your fingers (or a plastic lever, but in no case with something metal) to pry the right edge of the glass from the side driver's seat. Pull the glass towards you until a gap of approximately 0.5 cm is formed.

Step 2. Insert the tonometer cuff into the gap formed.

Step 3. Pump air until the gap increases to 1.5-2.5 cm.

Step 4. Make a long hook from a hanger or wire.

Step 5. Insert the hook into the crack at the top of the window.

Step 6 Hook the door lock button. In some cases, it may be easier to grab and pull out keys that were left in the car.

Any driver can lose a car key. This is very offensive, but it is even more offensive when the key remains in the ignition, while the car continues to operate, and the doors are blocked by the central lock. In addition, it is not possible to use a spare key due to the fact that the mechanical drive is disabled through the external cylinders in the door locks. But there is no need to panic, there are ways to open a car without keys.

First you need to decide on the most in a convenient way, with less damage to the car, your budget and, of course, your nerves. So, what methods can you use to open a car without a key, in addition to those given on vskrytie-avtomobiley.ru?

What are the ways to open a car without keys?

1. Break the glass. The method is quite simple and fast, but not economical, since car glass They are quite expensive, even if it concerns the blind rear window. Do not forget that if you do not follow certain safety measures, there is still a chance of getting injured - only in the movies, when breaking glass with your fist, the hero is left without cuts. It is better to use something heavy: a hammer or a stone wrapped in a rag.

2. Wooden wedge. Find or make your own wedge 20-25 cm, with a thickness of 3-4 cm at the base. After this, take a thin metal rod and make a hook at its end. Carefully, in order to prevent damage, using a wedge, you need to bend the edge of the door in the upper corner, carefully driving it with your fist between the counter and the frame itself. The rod is inserted into the resulting gap with the hook inside, then the blocker is rotated.

3. Wire hook. You need to take a piece of thin but stiff wire, about 60-80 cm, and make from it a one-sided hook with an angle of 45°, as well as about 10 cm in length after bending. We insert a wire hook between the seal, which can be bent if necessary, and the glass, carefully from the side of the door handle, inside. You need to feel and pick up the door pull, which has a button, after which all that remains is to pull the hook simultaneously with the pull upward and open the door. Similar method suitable for cars domestic production.

4. Electric drill. It is enough to drill out the core (cylinder) of the door lock and the door will open. You can take a metal blank similar in shape to the key, then drive it into the center of the cylinder and turn it there. There is an opinion that such a blank is replaced by a powerful flat screwdriver or steel nail scissors. But all the same, after this method you will need to replace all the larvae or you will need to carry different keys.

5. A two-meter piece of wire. In imported cars, the locking system is organized so that when the door handle is opened for the first time, the unlocking occurs central lock, which is used for emergency opening of car doors. You will have to make a small hook on the wire, which is inserted between the counter and the corner at the top of the door. By pushing the wire deeper into the interior, you need to make bends, which will allow you to pick up the door handle, and by hooking it and pulling the wire, the door will open.

6. Rope or cord. Any piece up to a meter long is enough, in the middle of which a loose loop is made, which is inserted between the counter and the uppermost corner of the door. If this is not possible, use improvised means to bend the corner a little. The loop lowers to the door closing button, tightens and pulls up: the button is pulled up, opening the door. This method can be used in those cars where the button for internal closing is located precisely at the top of the door card, protruding above its surface.

7. Contact specialists. Such services are quite common, and the craftsmen who provide them have both some skills and special tools, they do the work quickly, and, moreover, the cost is often cheaper than replacing it later broken glass, paint over scratches or repair a door that was bent incorrectly.

A qualified specialist will immediately figure out how and how to open the car without using a key; in addition, he will offer the customer various options and lead them possible disadvantages and advantages, will announce the cost of each of them.

What can a technician offer for emergency opening of a car?

1. When dealing with expensive cars, in order to prevent any damage from occurring, opening door locks carried out using special equipment. Although this option is very expensive, there is a guarantee of high-quality work.

2. The emergency opening procedure is similar to method No. 5 in the list above. The only difference is that pneumatic tools, a telescopic manipulator, and vacuum suction cups are used. As a rule, this is used by masters who do not have modern equipment and those who do not know other ways.

3. Unlock the lock by penetrating the door glass seals. To do this, the specialist must be aware of the structure of the kinematic locking mechanisms of automobiles with which he will deal; in addition, he needs skills and availability special tool. But what internal mechanisms will remain intact cannot be guaranteed, and there may also be costs for subsequent repairs of the locking system.

Unfortunately, unpleasant situations can arise at the wrong time and, sometimes, there is no contact with specialists or there is absolutely no time or opportunity to wait for their arrival for some reason. Then you have to act on your own, remembering how to open a car without keys, as well as what is the easiest way to do it. The main thing is not to be nervous, just remember what exactly to do, then everything will definitely work out!

Important!

The above methods are used only when emergency opening only personal car and only in the presence of the owner himself.

", I will try to help those who have become victims of a situation where the car doors are locked and the key remains in the ignition or simply inside the car. If you have not yet encountered such a problem, I advise you to read this article so that if this occurs troubles, you knew how to act in this situation.

This article will help you save time, money, and your own nerve cells.

I would like to note right away that the purpose of this article is to help those who find themselves in an unpleasant situation and cannot get into MY car. I am in no way advocating any illegal actions and am not an experienced burglar, and this article is not positioned as a manual for car burglars. All I want is to help the “drowning” who are in an unpleasant situation associated with automatic locking of car doors.

Let me start, perhaps, with the fact that this article is more of a cry from the heart than a regular guide for beginners. Why? Yes, because the other day I, the author of this article, found myself in such unpleasant situation when the key remained in the ignition and the doors slammed shut. To be honest, I personally, like most of those to whom this happens, did not believe until the last moment that such a fate could befall me. I thought that this could happen to anyone, but not to me, for which I actually paid...

I was never able to understand why this happens. Why car manufacturers came up with such an option is not clear to me personally. Perhaps you will have some ideas on this matter, in which case do not hesitate and comment.

Here is how it was. I got out of the car just for a minute to get some fresh air while I waited for my wife. The key was in the ignition, the engine was turned off, the radio was working and the lights were on. When leaving the car, I didn’t block anything or press any special buttons, but imagine my surprise when my wife pulled the passenger door handle and said that the door was locked. Not believing her, I pulled the handle driver's door and with horror stated the fact that the car had slammed shut... I still don’t understand why this happened, perhaps this is some kind of protective function or just a “glitch” of the central locking itself ( central locking), but the fact remains that I can’t get into the car, the key is inside, and I don’t have a spare one. Autumn, night, first frosts, mobile communications practically do not work... We've arrived! What to do? The first thought was to break the glass, but, of course, I didn’t do it right away, because I once read an article about how you can open a door without a key if the car is locked. After rummaging through my memories, I remembered several methods that I will now introduce to you.

First What you need to do is remember about an additional set of keys for your car. Even if they are 10, 20, or even 50 km away, it is cheaper to go after them than to break a window. If you don’t have any, then I sincerely sympathize with you, read on, perhaps other methods will help you.

Second way - find the number of a company that specializes in such emergency door openings. How to do it? If you have a smartphone or laptop, try to “find” the Internet. We are looking online for " emergency opening of car doors", "car doors slammed, key in the lock", "the doors are locked with the key in the car", etc. The search will give you a list of sites that can help you. If you don’t have the Internet or don’t know how to use a computer, then the solution is the following, call a friend and work through them, let them find the number or people who can perform an emergency opening car door. A specialist will open the door in a matter of minutes, and will charge no more for the work than you would have to pay for the glass and installation of a new one. Moreover, this method the better that all the windows will remain intact, and when selling a car this is an important plus. When buying a car, buyers check the production date of the windows and if they find a discrepancy, they are unlikely to believe that it was an unpleasant situation in which all the doors in the car slammed shut and you yourself had to break the glass. Most likely, the potential buyer will decide that the glass was changed after an accident, and a car after an accident, as you understand, is not the best option, so, most likely, you will be selling the car for a long time...

Method three - bend the edge of the driver's door and use something long to press the ESP (power window) button. The method is good provided that your ESP works in all positions of the ignition key. To me, in in this case, no luck, the trick didn’t work, the key was in the wrong position and even when we reached the button, we couldn’t lower the window. The principle here is this: between the door and the body we install something like a wedge, which makes it possible to bend the door, insert something metal or whatever is at hand into the resulting gap and press the button to lower the window. When the glass goes down you can open the door. As a blade, you can use a kitchen spatula or, for example, a very a good option- blood pressure cuff. It is necessary to insert a pillow from a device for measuring blood pressure into the gap, after which, using a “pear”, we pump in air, which will increase the volume of the cuff and the gap between the door and the body will become sufficiently large to carry out the above operations.

Fourth method - rope and knot. This method is very effective in the case when the door lock button is located on the door card near the glass itself, for example, since on,. In order to open car doors using this method, you will need a piece of rope or, in extreme cases, a sneaker lace. The principle is the following, you need to make a loop that can be tightened if necessary. We carefully insert the cord with the loop from the end of the door into the interior of the cabin, then place the loop opposite the door lock button, put the loop on the button and tighten the loop. Next, place the ends above the button and pull up, this will allow you to lift the button and unlock the deri.

Method five - wire with a hook. Fold down on the driver's door rubber compressor and insert a wire with a hook at the end into the gap formed. With this hook you need to pry the rod of the lock opening mechanism and pull it up. As a rule, after this manipulation the door opens. Structurally, this thrust is located in different ways, so it is quite difficult to give any specific advice; you need to act according to the situation.

Sixth method . This method, in principle, repeats the previous one, it’s just that in this case we will act not on the traction, but on the trunk opening button. We proceed in the same way, bend the hook from the wire, bend the edge of the driver's door and try to reach the trunk opening button. After the trunk opens, we recline the seat, make our way inside the cabin and open the doors.

Method seven - we break the lock. This method should only be used when as a last resort when other methods cannot achieve the required result. It consists of using brute force to influence the door lock cylinder, after which you will have to repair the lock, and also, most likely, replace all the door and trunk cylinders. By the way, most likely, after this you will have two keys - one for the doors, the second for. If this does not bother you, you can use this method, however, due to the high cost, I would recommend considering it only if absolutely necessary.

Eighth method - radical. If all of the above does not help, you will still have to break the glass. Before breaking glass, you need to think carefully. It seems like a no-brainer, but if you rush, you can end up with such “stuff” that repairs will cost many times more and there will be twice as many problems. First, you need to find out what kind of glass needs to be broken; for this, either yourself or through your friends, find out the cost of all the glass separately, find out if they are available, as well as the cost of installing it. Weigh the pros and cons, and then you can start beating. If you have tape on hand, then before the impact it is better to cover the glass with tape, this will hold the fragments and prevent them from scattering throughout the cabin. Don't just cover the area you're going to hit.

You must hit carefully; do not try to be a hero and try to break the glass with your bare hand or foot. Firstly, this glass, whatever you say, you can cut yourself, and secondly, it does not break as easily as they show in the movies. For example, I broke the glass in my car the fifth time using a metal pry bar. If you have a drill on hand, it would be a good idea to try to drill through the glass, this would allow you to avoid a million pieces of glass and at least get home without problems and drafts. If you don’t have a drill, hit it with whatever you have, a stone, a piece of wood, try to break the glass so that it doesn’t fall out completely, but only allows you to stick your hand in and open the door. When breaking glass, you should wear gloves, this will save you from unnecessary problems and unnecessary blood... After you solve the problem, the hole must be sealed with tape or cellophane, in short, the hole must be sealed by any means.

How to avoid such situations?

Now I'll give you a few useful tips how to make sure you never encounter a similar situation, or at least get out of it with minimal losses.

1. Try to never leave the key in the car. When leaving the car, take the key out of the lock.
2. Make a duplicate of the key. If you have a duplicate, you can always return home, take your second key and use it to open your locked car. If you don’t want to make a full-fledged key with a chip, make a regular master key (a key without a chip), it will be cheaper and if this problem occurs, you can easily open your locked car. Although I would recommend that you still spare no expense and make a full-fledged key with a chip. If you lose yours the only key, then making a new key from a dealer without the original key will cost you a huge penny.
3. Find out the number of the company that provides services by emergency opening cars before it happens to you.
4. Don't use the option automatic locking doors
5. Keep at least one door closed when you get out of the car with the key in the lock; keep them closed but not locked. If the doors are locked, you will be able to get into the car.
6. If you leave the car for a long time, take the keys with you.
7. When warming up the car, leave one door open or at least open the window. Alternatively, you can take a keychain with you remote control and leave the key in the lock. If the door gets locked, you can use the key fob to open it.

I have everything, I hope this article will help someone solve big problem. If you know other ways to open a car when the doors are slammed and the key is in the lock, do not hesitate to share them using the comment form..

None of the car owners is immune from an extremely unpleasant situation when their doors are locked and the key remains inside. But no matter how rushed or nervous you are at this moment, you need to pull yourself together. There is a solution to any problem, so don’t worry unnecessarily.

Tip #1.

After making sure that the keys are in the car, first consider the option of using a duplicate. If you have a spare key at home, ask a relative to bring it. If you have traveled far, you can try using the key fob using your phone. In this case, the person pressing the opening must hold the key fob at a distance of about 20 centimeters from the microphone, and you can use the speakerphone.

An option for lazy people.

For those who do not like to experiment and for whom the first advice does not suit, it is suggested to call a special service. Just keep in mind that their services are not cheap, they are not performed instantly, and there may be problems with quality (“specialists” are different). Therefore, it is better to call trusted or recommended companies. It is not uncommon for such masters to use the methods described below.

For others.

If you trust your hands more or simply don’t have the service you need nearby, then you can do everything yourself. It’s just worth considering that different cars open differently. As a rule, than newer model, the more difficult your task. And if done incorrectly, your car can be damaged. Before using the following methods, try using your palms to lower one of the windows or use a similar (if available) key. The probability of success is very low, but in some cases, not new cars were opened this way. The main thing is not to overdo it; if it doesn’t work out, stop in time.

Using a hook.

This method is most often used by owners of domestically produced cars. First you need to find a wire of medium thickness, preferably rigid. You will need a piece of long wire about half a meter. On one edge we make a hook at an acute angle (45 degrees), so that the length of the bent part is up to ten centimeters. The hook needs to be inserted between the glass and the seal (after bending it, if necessary) and try to touch the door rod, after which we pull the wire up. If your car does not have a protective cover on the lock, then everything is very simple, otherwise this option is not for you.

Using a loop.

If your opening button inside the car is not hidden in the trim and protrudes at least a little upward, then you can pry it up with a loop tied on the edge of a fishing line, rope, or even a shoe lace (you are more likely to have one at this moment). In some cases, you will have to slightly bend the door in the corner. For this you can use, for example, a wooden wedge pre-wrapped with a piece of fabric. You need to start it carefully, lightly tapping it with your hand. Otherwise, the car may be damaged.

If you cannot hook the button, you can return to the option with a hook, only taking a longer piece of wire 1-2 meters. Having brought it inside the car (through the gap in the corner of the door or if you can lower the window even a little), we hook it door handle and open the door. When choosing an opening option, you need to take into account the features of the security system of your iron horse.

More radical measures.

Those who have a drill on hand and have no other options are encouraged to simply drill out the “cylinder” of the lock. But before that, you should think about what will cost less: replacing all the locks or, for example, broken glass. If you don’t have a drill at hand, you can replace it with a screwdriver, sticking it into the lock secret and twisting it with force, the effect will be the same. Those who decide to break glass are not advised to choose a “window window” for this purpose, since replacing it is more expensive and problematic. And be careful, because this is not a Hollywood action movie, where fingers are pierced through the glass without leaving a scratch.

And I also want to note one point, if you want to know last news about electric vehicles, then you should visit the resource. All the latest news about electric cars Tesla and much more.

Quite often there are situations when people forget their keys inside the car or in the trunk, and then, naturally, they puzzle over how to get inside. You can find a lot of ways to open car doors without a key.

Unfortunately, not all of them may be suitable for a particular model, and if the alarm goes off when you try to open the door, you may also run into a patrol, who will have to explain the seriousness of such an unenviable situation.

What to do if you cannot get inside the car due to your carelessness?

The easiest way is to simply call home and have a spare set of keys delivered to you. Breaking the glass with a hammer is also a way out, but you really need to hit with all your might, since the hammer doesn’t give in so easily; try to turn away from the glass while hitting so that the fragments don’t get into your eyes. In addition, it is not a fact that the glass will be broken the first time.

There are also corresponding services that deal with opening locks; such a service will cost you, depending on the complexity and distance from civilization, 2-5 thousand rubles.

However, you can also use improvised objects to open a slammed door.

Method one

We find a strong, not very thick wire, the length of which is approximately equal to the length of your arm. We bend its end so as to form a hook. We bend the door seal above the door lock and carefully push the wire under the door. The task is to feel the lock rod and lift it up a little, as a result of which the door should open.

Method two

You can use a rope or fishing line, and the fishing line is strong and thin enough that it can be easily inserted into the gap between the door seal and the body. The essence of the method is to tie a small loop, which is tightened when both ends of the fishing line are pulled. By bending the seal in the upper right corner of the door, moving the fishing line to the right and left, we push it inside the car, and when it is inside, we try to put the loop on the flag, hook it and lift it up. The method is suitable for cars where there is a flag for closing the lock.

Method three

For those cars that have a flag on the door, another method you can use is to open the door using a tennis ball with a small hole. The ball needs to be pressed against door lock so that the hole for the key is exactly opposite the hole in the ball. Then by pressing hard you direct a stream of air onto the ball inside the castle and the flag rises up.

It is worth noting that not all of the above methods may be suitable modern foreign cars and especially expensive cars, whose manufacturers have carefully thought through all the ways to open locks, installing handles and flags that are smooth and tapering towards the top, and it is almost impossible to hook them. But for our “Muscovites” and “Zhiguli” such methods are quite suitable.

If you drive an expensive car, for example a VW Tiguan, then you need to be familiar with the instructions and design of the car. In the same Tiguan, there is a small slot on the back door into which you can insert a wire, pry up a small latch and open back door. Naturally, you will only know about this if you carefully read the instructions. In addition, you don’t have to tear the seal or break the glass and then pay from two to five thousand for a new one and its installation.

IN winter time You also need to know how to open doors without a key. The situation when the battery is discharged and mechanical locks freeze is quite common. You have to warm up the locks so you can turn them. If warming up does not help, then you can try using another battery by connecting it through the cigarette lighter to the terminals of your battery and to ground - the alarm key fob should work. Or you need to find the hood lock cable, which is located behind the headlights or radiator; you need to pull it sharply with a wire hook.

If none of the methods helps you, then your only option is to make a duplicate key at the dealer, which can take some time and cost up to ten thousand, although professional lock pickers can handle any system. All that remains is to advise you to never forget your keys in the car, and always be careful.