Fuses located in the fuse box in under the hood Lada Xray

Not so long ago, VAZ began to produce a new model of Lada X-Rey and the most common malfunction of this hour is the brave of fuses. At the same time, their burnout does not have to be the cause of short circuit of wires or other malfunction of electrical equipment. When working, the fuses heat and with time they can burn.

For short circuit, not a single brave of fuses of the same chain is characterized. When replacing the fuses, it is necessary to apply them the same nominal value. Also, when replacing, it is necessary to use only high-quality fuses, and do not buy fuses without packaging not known manufacturers. How to choose fuses and which consequences of the use of non-high-quality fuses can be described in the article "Automotive fuses. How to choose". The use of non-quality and non-relevant fuses can lead to the failure of the fuse block or the fire of the vehicle. Like all the latest models of Lada Xray Vase has two fuse blocks. One is located in the open space, and the second in the car.

Fuses of Lada X-Rey in the windscreen space.

The fuse block in the pumpapot space is borrowed from the previous model of Lada Vesta, and those protected by fuses and switched circuit relays are the same. It is also located near the left wing near the battery and closed with a lid. On the reverse side of the lid there is a description of the chains of protected by fuses and their location scheme.

Description of fuses.

Fuse number	Nominal	Protected chains
F1 *	10A.	Fog lights
F2.	7.5A.
F3.	25A.	Rear window heater
		Heaters of outer mirrors
F4.	25A.
F5	70A.
F6.	70A.	Consumers Side Power Salon
F7.	50A.	Controller of the course stability system
F8.	40A.	Windshield Heater 1
F8 (without heating windshield)	30A
F9.	40A.	Windshield Heater 2
F9 (without heating windshield)		Reserve
F10	30A	Outlet for additional consumers in the trunk
F11	—	Reserve
F12 **	30A.	Starter start circuit
F13	—	Reserve
F14 **	25A.
F14 ***	30A.	Electronic Engine Management System
F15	15A	Air conditioner compressor coupling
F15 ** (without air conditioning)	30A
F16	50A.	Radiator cooling electric fan
F17	70A.	Controller of automated transmission (AMT)
F18.	80A.
D1 (installed on site F19)		Diode system air conditioning
D2 (installed on site F20)		Engine cooling diode
F21	—	Reserve
F22	—	Reserve
F23 **	15A	Control
		Air conditioner relay management
		Oxygen sensor 1.
		Oxygen sensor 2.
		Adsorber purge valve
		Phase sensor
F23 ***	7.5A.	Oxygen sensor 1.
		Oxygen sensor 2.
		Inlet Length Control Valve (only for 21129)
		Adsorber purge valve
		Phase sensor
		Phasemer valve (only for 21179)
F24 ***	15A.
		Radiator electric fan control unit
		Ignition coil 1 cylinder
		Ignition coil 2 cylinder
		Ignition coil 3 cylinder
		Ignition coil 4 cylinder
		Nozzle 1 cylinder
		Nozzle 2 cylinder
		Nozzle 3 cylinder
		Nozzle 4 cylinder
		Module of electrical space with fuel level sensor
F25 ***	15A.	Fuel pump

** Fuses used only performed with H4MK engine

*** Fuses used only performed with engines 21129 and 21179

Description of the relay located in the block of fuses in the windscreen space

Relay number	Nominal	Purpose of relay
K1.	20A.	Alarm Relay
K2.	—	Reserve
K3 **	40A.	Starter relay
K3 *	20A.	Starter relay
K4.	40A.	Main relay Esud.
K5.	20A.	Air conditioner compressor clutch
K5 * (without air conditioning)	20A.	Radiator cooling electric fan relay
K6 *	20A.	Fuel pump relay and ignition coils
K6 **	20A.	Fuel pump relay
K7.	40A.	Wind Glass Heating Relay 2
K7 ** (without air conditioning)	40A.	Radiator cooling electric fan relay
K8.	40A.	Windshield heating relay 1
K9.	20A.	Sound signal relay

* The relay set is specified for execution with the engine H4MK

** The relay set is specified for execution with engines 21129 and 21179

Fuses located in the Lada Xray salon

Fuses Lada X-Rey in the car.

The fuse block in the Lada X-Rey salon is located on the side of the torpedo from the driver's side under the lid. On the back of the lid there is also a layout and a description of the fuses. There are also some relays. The used fuses are flat, knife type, medium size, the most common on modern domestic cars. Some relays are located in the fuse block.

Relay in the cabin fuse block

Description of fuses

Fuse number	Nominal	Protected chains
F1	30A	Electric windows of front doors
F2 *	10A.	Far Light (headlight left)
F3 *	10A	Far light (headlight right)
F4 *	10A	Middle Light (headlight left)
F5 *	10A	Middle Light (Headlight Right)
F6 *	5a	Overall lights (headlights left and right)
F7 *	5a	Overall lights (rear lights left and right)
		Lighting lighting lights
		Backlight of the headlight light corrector switch
		Backlight of the center lock of the door locks
		Illuminated emergency signaling switch
		Illuminated air conditioning control panel *
		Backlight of the Soft Parking System Switch
		Illuminated switch power windows in the driver's door
		Illuminated switch power windows in the doors / doors of passengers
		Illuminated cigarette lighter
		Illuminated interior lighting block
		Illumination of the radio / multimedia system
F8.	30A	Electrical windows rear doors
		Managing Relay Relay Relay
		power windows
F9 *	7.5A.	Rear fog fire
F10	—	Reserve
F11	20A.	Central Block Body Electronics (Side Doors Locks Motors, Trunk Castle Motor)
F12.	5a	Antenna immobilizer
		Controller of the course stability system
		Steering wheel rotation angle sensor
		Braking Signal Switch
F13	10A	Salon lighting unit
		Plafon lighting trunk
		Badmaker lighting plander
		SUKU controller **
		Climate Installation Control Panel **
F14 **	5A.	Rain sensor
F15	15A	Wind and rear plates
		Central Block Body Electronics (rear window cleaner)
F16	15A
		Front seats heaters
F17 *	7.5A.	Daytime Running Lights
F18.	7.5A.	Brake signals lamps in rear lights
		Additional braking signal
F19.	5a	Engine Controller Controller
		Central Block Body Electronics
		Additional body of body electronics * *
		Combination of devices
		Management of starter relay
		Controlling the fuel pump relay
		Automated Transmission Mode Selector
F20.	5a	Inflatable airbag control unit
F21	7.5A.	Reverse light bulbs
		Automated Transmission Controller
F22	5a	Electronasus steering power steering
F23.	5a	Safe Parking Management System Control Unit
		Light Headlight Electro Corrector
		Electro Corrector Light Right Headlight
		Electrocorrector switch headlights
		Control of windshield heating relay 1
		Control of windshield heating relay 2
		Management of rear window heating and outer mirrors
F24.	15A	Central body body electronics (power supply fuses F12, F13, F36 with
		delay after turning off the ignition)
F25	5a	Car terminal ERA-GLONAS system
		Additional body body electronics **
F26	15A	Central Block Body Electronics (Running Pointers)
F27 *	20A.	Middle Light (headlights left and right)
F27 **	5A.	Middle Light Headlight Signal
		Far Light Far Light Signal
		Fog lights
		Rear fog light
F28.	15A	Sound signal
		Performance lighting signal **
F29 *	25A.	Overall lights (headlights and rear lights)
		Far Light (headlights left and right)
		Rear fog fire
		Sound Relay Management
F30.	—	Reserve
F31	5A.	Combination of devices
F32.	7.5A.	Central Block Body Electronics
		Car terminal ERA-GLONASS system
		Radio / Equipment Multimedia
		Control of the relay of the additional socket in the trunk
		Heating electric fan relay
		Air conditioning control panel *
F33	15A	Cigarette
F34	15A.	Diagnostic connector
		Radio / Multimedia System
F35	5A.	Heated outdoor mirrors
F36	5A.	Electric drive exterior mirrors
F37	30A.	Starter start circuit
F38 *	30A.	Windshield cleaner
F38 **	30A.	Additional body of body electronics (windshield cleaner)
F39 *	40A.	Electrical fan heater
F40	—	Reserve
F41 **	25A.	Additional body of body electronics (daytime running fire right headlight, overall lights front, close light left headlight, distance light right lights)
F42.	—	Reserve
F43 **	15A.	Additional body of body electronics (power consumers after F19 salon fuse)
F44	15A.	Outlet for additional consumers in the trunk
F45	—	Reserve
F46 **	25A.	Additional body of body electronics (overall lights of the salon, fog lights,
		Rear fog fire)
F47 **	25A.	Additional body body electronics (daytime chassis left side, overall lights rear, Middle Light of the right light, Far Light left headlamp)

* Fuses used only performed by Optima (without rain sensor).

Dear buyers, in order to avoid errors when sending the harness of the Pan Lada X-Ray, in the "Comment" line, specify the model of your car, year of release.

The Lada X-Ray crossover is a modern model that is equipped with a fairly volumetric kit of all sorts of electrical and electronic equipment, which increases safety when driving, and provides comfort. Therefore, this car uses a complex electrical circuit onboard network. And the electric hammere is more difficult, the more it requires protection against closure and burnout. And for this, the fuses used in Lada X-ray are responsible.

Without electrical components, a modern car with a gasoline engine is impossible to even move away. Thanks to the wiring, all nodes and aggregates work as a single mechanism.

The wiring harnesses that are moving from the top-bottom car perform the only task - ensure uninterrupted transmission of electrical pulses between the components of a system or another. And if one of the wires has bad contact, or the terminal was burned or oxidized, then the operation of the chain will disturb or even refuse.

Wiring harness 8450020118 Lada X-Ray / Lada X-Ray Instrument panels with salon fuse box, designed to manage automotive driver in the Lada X-Ray / Lada X-ray car.

Lada X-ray has two mounting blocks two. It is due to the fact that the electrical and electronic equipment at the crossover is quite a lot. And if you install all the elements in one fuse block, it will be dispersed in size, and the place for its installation is difficult to find.

The separation of all fuses into two groups and accommodation in two blocks made it possible to find a place for them without any problems. It also made it possible to unknow the fuses for their intended purpose.

One mounted block placed in the cabin, At the bottom of the front panel from the driver. The fuses and relays installed in it provide the operation of lighting equipment, systems that provide comfort and so on.

The second of the safety blocks was installed in the subcontrol space and all elements installed in it are responsible for the operation of the electrical engine equipment, auxiliary systems, some elements of lighting and heating.

It is worth noting that the fuses on the onboard network are used in different ways. Some responds only for the functioning of some particular electrical equipment, but there are also those through which the power is powered by several consumers.

On the number of fuses and the operating parameters of some of them affect the power plant, as well as the presence of additional equipment. That is, for this crossover, several motors are offered, each of which has its own characteristics. For one unit, it may be necessary to preserve an additional floating element, and for another engine - no.

Mounting unit installed in the cabin. Getting access to it is very simple, it is enough to pry a lid and remove it.

For the convenience of extracting fuses, a special tweezers is fixed from the inside of the cover.

The saloon mounting unit includes 5 sockets under the relay (one - backup) and 47 - for fuses. The scheme is such:

The designation of the relay of the salon mounting unit- "K" with the numeric index and they are responsible for:

K1 - heater fan;

K2 - heated mirrors and rear windows;

K3 - blocking rear windows (electro);

K4 - reserve;

K5 - trunk socket;

On the position of the relay in this block, the equipment and the engine do not affect. As for the operating parameters, only K5 is 20 A, and the rest - by 40 amps.

In the salon mounting block of the fuses, a lot is sufficient, while the purpose of some may vary depending on the configuration.

To make it clear what kind of fuse and what is responsible in one or another configuration, we use the additional designation of the fused elements:

Without add. index - the purpose of the item is the same for all complete sets;

- (1) - are used in a car that is not equipped with a rain sensor (equipping "Optima");

- (2) - elements responsible for the operation of the equipment in the equipment with the sensor ("Top" and "Suite");

It is also a letter "F" and numeric index. Also, part of the nests are backup:

F1 - front door windows (electric);

F2 and F4 (1) - Lew Head Optics (Far and Middle);

F3 and F5 (1) - light of head optics (far and near);

F6 (1) - Overall lights of both headlights;

F7 (1) - Overhead lights, illumination of elements and samples installed on the front panel (keys, cigarette lighter, control of C-mi, etc.);

F8 - rear windows (electro), control relays of their blocking;

F9 (1) - rear PTF;

F10 - reserve;

F11 - Central Block Body Equipment (door lock gearboxes, fifth doors);

F12 - immobilizer antenna, C-resistance controller, steering angle sensor Steering wheel switch;

F13 - cabin light, luggage compartment plaffers and glove boxing. Also, the controller (2) and climate-system panels (2) can go from it;

F14 (2) - rain sensor;

F15 is the windshield washer, the central block of body equipment (rear window cleaning);

F16 - seats heating, audio system, navigation system;

F17 (1) - DRL;

F18 - lamps of stop signals, including duplicating;

F19 - Controller C-we control the power unit, basic and add. (2) Body equipment control unit, dashboard, starter and gas station relay, automatic transmission selector;

F20 - Passive security unit (pillows);

F21 - reverse light bulbs, automatic transmission controller;

F22 - Electric pump GUR;

F23 - Parking block, headlights, headlights and switches, glass heater relays (windshield, rear), side mirrors;

F24 is the main body of body equipment (fuse fuses F12, F13, F36 with delay);

F25 - the terminal navigation C-we, extra. Block body equipment (2);

F26 is the main body of body equipment (turn signals);

F27 - Middle Light of the headlight (1) or - signals for the inclusion of the near and far light of the head optics, PTF front, rear (2);

F28 - signal, additionally - the inclusion signal of the overall lights (2);

F29 (1) - Overall lights (front, rear), Far Light of both headlights, rear PTF, signal relay;

F30 - reserve;

F31 - dashboard;

F32 - central body equipment block, navigation system terminal, audio system (multimedia), trunk rosette relay, heating system fan, air conditioning system panel (2);

F33 - cigarette lighter;

F34 is a diagnostic connector;

F35 - heated side mirrors;

F36 - drive side mirrors;

F37 - starter inclusion circuit;

F38 (1) - windshield cleaner;

F39 (1) - Heating fan;

F40 - reserve;

F41 (2) - an additional body of body equipment (DHL of the right optics, the dimensions of the front, the near light of the left and long-headed headlights);

F42 - reserve;

F43 (2) - an additional body of body equipment (powered by all devices going beyond the f19 f19);

F44 - trunk socket;

F45 - reserve;

F46 (2) - Add. Block body equipment (PTF, salon overall lights);

F47 (2) - Add. Block of body equipment (DRL of the left headlamp, rear dimensions, melee light and long-range - left headlights);

Safety unit in the engine compartment

The mounting unit responsible for the operation of the power plant is set in the engine compartment. The body of the fuse block is made of black plastic and find such a box in the rotor space on the right side is not difficult. To access the fusible elements and the relay, it is enough to remove the top cover, folding the locks.

For the convenience of finding the required fuse or relay, the fuse diagram with the factory designation of each is applied from the inside. Additionally, each elements indicate its operating parameters, which makes it easier to choose the item to replace it easier.

The mounting unit of the engine compartment includes 8 relays and one backup socket, as well as 25 seats under the fuses, the amount of fused elements depends on the engine and configuration of the car.

Dear buyers, if you did not find the marking of your harness in the list, then when placing an order in the "Basket" in the "Comment to Order" field, you can specify the number of the desired harness.

Lada X-Ray / Lada X-Ray / Lada X-Ray / Lada X-Ray / Lada Wirkers The Fuse Block is tested by AvtoVAZ and is installed on the assembly conveyor when assembling a serial car.

The easiest way is to watch the marking of the old harness and order the same. We have all. If there is no such possibility - you need to provide the following data: car release, controller marking (ECU), engine volume, number of valves, air conditioning and ABS, fog headlamps in the car.

By car Lada X-Ray / Lada Xrei with the "Top" and "Suite" settings, many devices are cooked through the central and additional blocks of body equipment.

Other article articles and its analogues in the catalogs: 8450020118.

Lada X-Ray / Lada Xrei.

Any breakdown is not the end of the world, but a completely solved problem!

How to replace the dumplings by car Lada X-Ray / Lada X-Ray / Lada Xrei.

Dear buyers, in order to avoid errors when sending the cover of the mounting block of the relay and fuses of the engine compartment of Lada Vesta / Lada Vesta, Lada Xray / EX Rei in the "Comment" line specify the model of your car, year of release.

Solving any problem that is associated with the electrical equipment of the car begins with checking the fuses. Together with the relay are located in the mounting blocks (fuse block and black box) of the cabin or motor compartment.

Mounting unit 243825499R fuses and relays Lada Vesta / Lada Vesta, Lada Xray / X Reef is located next to the battery at the left wing - black box

To get to the relay and fuses block - squeeze both clamps and you can open the lid.

Locks are very fragile, it is important to do it carefully, not to break

In order to install the cover of the mounting unit 243825499R fuses and the relay in the engine compartment of Lada Vesta / Lada Vesta, Lada Xray / EX Ray in place - perform actions in reverse order.

If you eventually burned out some kind of fuses, it must be replaced. But before, you need to establish the cause of the fuse output, be it a short circuit, or high loads.

The manufacturer ultimately does not recommend installing fuses with a par value higher than specified in the table, because The fuse protects the wire, and not the electrical consumer itself. When installing the fuse with the face value above - than it is necessary, the risk of car fire is possible.

Other articles of goods and its analogues in the catalogs: 243825499R.

Lada Vesta / Lada Vesta, SW and SW Cross, Lada Xray / X Rey.

Any breakdown is not the end of the world, but a completely solved problem!

How to independently replace the cover of the assembly unit of the fuses and the relay in the engine compartment by car Lada Vesta and its modifications.

With the online store Avtoazbuka. repair costs will be minimal.

Just compare and kill !!!

All lada x-ray packages, including the basic, have an extensive set of electronic assistants, including the ESC system.

ESC

The ELECTRONIC STABILITY CONTROL complex itself is a stabilization system and similar to ESP. His appointment is to prevent the car breaking into a skid. As for the items, the main difference is to manufacturers of equipment.

Problem

The first instances of the X-Ray resivers were completed with electronics, which could not be deactivated. However, in certain situations, the specified system only interfered. That is why the question arose about the disconnection of the ESC system to Lada Ix Rei.

A little later, AvtoVAZ introduced the ability to deactivate through the key in the cabin, and also sent instructions to the dealers to install such a button. However, there is another proven way to independently disable the ESC system to Lada X Rei.

Disconnection

It is carried out by removing one of the fuses, however, it must be borne in mind that in this case the ABS will turn off. For the correct operation of the ESC complex, several fuses are responsible at once, however, only one will have to take out, for example, a fuse at 50 A, which is located in the block under the hood.

IMPORTANT! While removing the fuse, the key from the ignition lock must be removed.

After the work and inclusion of ignition, 3 icons are required to light up on the dashboard:

1. Parking brake.

After that, it remains only to start a crossover and try to drive a problem area with deactivated automation. However, if you do not have the skills of off-road driving, the removal of the fuse is unlikely to seriously help you.

As it can be seen independently disconnect the ESC system to Lada Ix Ray is quite simple. The main thing - do not forget to insert the fuse back to the mounting block.

Visually, the whole process is demonstrated in the video.