Car owners often have various problems associated with small problems of work of the most common elements. Take, for example, wipers. This small detail affects the safety of motion. Moreover, it is not recommended to start moving with poorly working janitors. With bad weather flying towards insects on the highway and other similar situations without janitors can not do. If the windshield is flooded with water or mud, then visibility decreases sharply. And this in turn can lead to an accident. If you want to avoid this difficult situation, then watch the condition of the janitors. Many motorists change rubber brushes when they begin to "smear". Some prefer to buy original spare parts, others arrange cheaper counterparts. But the question comes down primarily to the quality of the gum themselves on the janitor. And replace them much cheaper than buying a new item.

How to start the replacement of gum on janitor?

If you decide to change the gum on the janitors, then to start decide manufacturer. It is best to acquire models of famous brands that have proven themselves well. But many motorists recommend certain firms that are distinguished by high quality at a relatively low price. The cost of these spare parts is small in any case. For example, known DENSO will cost much more expensive than Masuma models, although their quality is approximately the same.

Everyone who does not know how to replace the gum on the janitors should begin with a small one - dismantling the brush itself. To do this, it is necessary to include wipers and wait for the middle of the cycle, when the wipers themselves reach the highest possible. At this moment (it is necessary to catch it) Turn off the ignition. And then your wipers will stop in the selected position.

After that, the wiper must be carefully separated from the windshield. Do not apply force, it can be brought or break.

Become on the side of the driver and take the brush. It is necessary to turn it several times counterclockwise, after that it will take off the wiper. On some models, it is enough to rotate the brush by 90 degrees and pull up. There are models where a rubber brush is fastened with a plastic retainer, which needs to be carefully squeezed. A similar procedure must be carried out with a second brush, ending the front passenger.

Dismantling the brush of the janitor with a hook-type fastening

Dismantling the brush of a janitor with a button type button

Disassembly of the wiper brush with a side pin mount

Dismantling of the brush of a janitor with a type of side clamp type mount

Dismantling the brush of the janitor with a fastening of the type of bayonet

Dismantling the brush of a janitor with pin-type mount

Dismantling the brush of a janitor with a fastening of a tie type

Dismantling the brush of the janitor with side mount

Dismantling the brush of the janitor with a fastening of the top castle

Replacing the gum themselves with a complete analysis of the brush may seem a long procedure, but in fact you will leave for no more than twenty minutes. But the savings will be noticeable.

How to replace the gum on the janitor

What should be done:

1. remove both sidelocks with a brush;
2. remove rubber spoilers;
3. delete (pull) old elastic band.

After that, there is a problem with installing a new gum. Someone manages gently insert it into place old. But it is very difficult to do it, because the rubber clings to the guides and does not particularly slide. You can try to smear with soap to zoom in slip, but this method does not help everyone. If you do not want to tire yourself with a slow tensioning of the gum on the brush, then simply disassemble it.

It is enough to remove one (any) metal guide. After that, a new gum must be put on the guide that remains in the brush. Make it is easy, but make sure that the gum does not break. Then insert the second guide to it and thoroughly straighten the gum. The work is done. It is only necessary to return to the place of spoilers and secure the design of the side plugs. Be sure to check the reliability of fixation of all items, since the wipers account for a significant burden during the weather: rain, snowfall and even strong wind. It will be very problematic to purchase separately one stub on the brush.

How to change the gum on frameless janitars

You need to start with a long brush. Take her in hand and carefully consider. You will notice two plugs around the edges. And you need to remove exactly the one that holds an elastic band. Learn the right plug is easy: it is enough to move the gum left / right. If you see that one of the sides is fixed, then you need to remove this plug. To do this, you will need a simple flat screwdriver, which you can make a plug, without damaging it. If you are not mistaken, then under the plug there is a gum fixer.

Now you need to bend it to three or four millimeters so that it let go of the old elastic band. We get rid of the details that spent your time and insert a new one in its place. If it is too tight, then you can lubricate the gum with soap, which will noticeably facilitate the work and increase the slip. The size of the gum must coincide with the base, do not have to cut anything. Do not forget to clamp the retainer back to fix the new part of the rubber brush. After that, return to the location of the plug. The first part of the work is over.

Replacing the elastic bands on frameless janitors also involves work and with a short brush. The beginning of actions coincides with the already described. You will need to understand which of the parties is the retainer. Then remove the plug, remove the retainer and remove the old gum.

But then you are waiting for small difficulties. The fact is that the new gum will be longer than that that was before. What to do in this situation? Insert the gum on the entire possible length, then clamp the lock back. After that, do a sharp knife, cut the rubber band for the most end brush.

The problem is solved. It remains only to return to the place the plug.

Many people better perceive information from video master classes. If you want to know how to replace the gum on the janitors of the video, then carefully follow the actions of experts. They use the most common tools that will be found in every garage and even in every home. In addition, you will not need special skills to replace the brushes on your car. Make it can even a person who is not very familiar with his device.

But still experts advise changing gum no more than two or three times on some janitor. After all, the main design is also wearing and requires replacement.

How to replace gums on janitor: video

Among the car owners there is an opinion that if the janitor is frameless, then the gum on it is not changed. Everything that can be done with this janitor is to throw it out and buy a new one. In fact, it is not. You can change the gum on this type of janitors, and in this article we will tell readers how the replacement is done.

There are several of them:

• The wipers began to publish an unpleasant creaking during work.
• Rubber was worn out so that the janitor began to scratch the windshield.
• The wipers do not cope with the work, and water drops remain on the glass even after several passes.

All these moments are indicated by one: the gum of the janitor, due to wear, ceased to fit tightly to the glass, and therefore, it should be replaced as soon as possible.

Tools to remove and replace

1. Shutter with flat sting (medium sizes).
2. Shutter with flat sting (the smallest).
3. Dishwashing liquid.
4. A set of new gum for janitors.
5. Capacity with hot (but not boiling) water.

How to change: sequence on the example of Bosch

Video to replace the gum on the wiper

Important moments

• It is strictly not recommended to remove the plugs of the janitors, pre-not warming them. Plastic, from which they are made, very fragile, and breaks even from a minor effort.
• When flexing the fasteners, it is impossible to make too much effort. Steel, from which these mustache are made, is quite plastic, and if you get used up too much, it may not return to its original position, which means it will not hold a new rubber band.

As can be seen from this article, it is possible to replace the gum on the frameless janitor. The most important thing is to pre-heat its plugs and use only the thinnest dumplings for flexing the fasteners.

Copywriter with five-year experience.

What better gum for wiper brush? Substitution of rubber in wiper brushes

Do you understand how elastic bands are evaluated for the wiper brush? Naturally, the main thing is how they wipe the glass. Excellent brushes should not leave the water films, no strips that exacerbate visibility. At the same time, it is fundamentally and how they clean the glaciation and frost, do not become with all this wooden in the cold. In addition, it plays the role and resistance of rubber to reagents that are included in glass liquid, also to those chemicals that use road services. Based on all these characteristics, the rating is based on which brushes and rubber bands for the wiper brush are evaluated.

We will see some species that, on the view of professionals, are among the best and suitable for both rear and windshield cars of different brands.

Heynell All Seasons

Many specialists in publications for motorists are expressed in favor of these species. Gum for wiper brushes They differ in slowiness, and even after months, they do not creak and do not rustle when working. The effect is obtained due to rubber raw materials and a clear calculation of the edge angle.

At the same time this brush It is not sufficiently tough, especially for the cool season, because at such a time the middle of the gum rises and no longer cleans the surface.

DENSO NDDS

Flexible rubber of this brand cleans the surface is quite excellent. Even with long-term operation, no scratches or scratches arise. This frame design with the right fastening points makes the full grip of the brush with glass.

But this type of rubber can not be attributed to long-term. After cold weather, the embroidery will be heard when working. But even with all this, it will continue to work perfectly well and perfectly wipe the glass.

Alca winter

These are frameless brushes. Gum for the wiper brush have an average hardness and will be perfectly withstanding the work for many hours in low temperature criteria.

Read the same:

The defects them are only that they are not suitable for the warm season, and they should be changed to others. And if this is not done, then the gums will be in disrepair very rapidly.

Sparco SPC-10XX

For these brushes, the definition of universal is the most suitable. They just install them for at least what car without using special adapters. In addition, they are perfectly managed with their own work at least some season.

How to replace gum brushes brutals.

A good selection of brushes here: subscribe to the channel here :.

Replacing the rubber bands of frameless janitors

Replaceable rubber For janitors wipers.

They have plastic overlays that protect the surface from frost, and on rubber graphite spraying, lowering the friction coefficient.

Read the same:

DENSO WIPER DLADE HYBRID

This type of brushes could be considered almost the best (in the last extent so about them spoke in the magazine to configure). The glass, which was wiped out by this elastic band, acquires such a look as if only released from the factory. But there is one big minus. The Japanese manufacturer really makes them so that they will serve for years. But these brushes are performed to the same in Korea. But the latter can no longer be characterized in the same way as the real Japanese. To chagrin, it is not likely to distinguish one of others. Hence the downward rating.

Heyner Hybrid.

These rubber bands, wiper brushes for trucks and passenger cars are not one test drives. The highest temperature and ultraviolet are actually not reflected on their functionality. But for the winter time of the year they are not suitable, because they do not have the casing at the fastening of the lever to the brush. Therefore, the compounds will be rapidly driving ice, and no brush movement will fail.

DENSO RETROFIT (LHD)

Many autoconecers specifically this brush includes factory supplies. It is a frameless, hard set. They are distinguished by good aerodynamics and silent when working. But the glass of rubber bands can not be completely completely. In main difficulty, they can meet in winter.

Bosch Eco.

Metal frame of this species has anti-corrosion coating. This is tough rubber brush. Uniformly wiping the surface in length, it provides minimal lifting force. Advantages are complemented by a very competitive price. However, acquiring this product should be paid to the original, and not an option from China.

These species are far from the entire list of top models. For example, a gum for the wiper blades Valeo and many others are perfectly shown. Let's see how to change these details.

Replacing rubber stuffing wiper brushes

Of course, you can come to terms when graphite or silicone gums for wiper brushes creak. You can deal with it in various ways. But when the wipers are already stopped wiping the glass, nothing else remains like change them.

To replace only a screwdriver, having a thin blade, and pliers.

The janitor is removed from the leash, flexion tape clamps from rubber with a screwdriver. Do it only just so that rubber Could get out of the brush.

Then remove plates from it that hold the form of gum. At the same time, you need to remember the direction of the bends, so that it is not to confuse them, since the gum will not be able to press the glass otherwise.

In the plates there are samples, which includes tape from rubber. Rarely, but it happens when the sample width is less than the thickness of the rubber groove. Then a thin supphyl is gently expanding.

A new tape is inserted into the locks, which should pass there freely, but without much hopping in the rocker, otherwise rubber Warmly wear out. Best of all, if you do not clean new rubber bands for wiper brushes, buy (Rostov, Moscow or Peter online stores quickly deliver items to any region of the country) brush themselves, and not continue experiments with rubber bands. Otherwise, it may turn out that as a result, they will have to lay out the amount greasy than the finished set of brushes.

Sometimes, however, it's enough to find how to twist the gum wiper brushes (This is done with gasoline, White spirit or just hot water) so that they normally work fine, than to change them to a new set.

Windshield cleaners are very simple, but since it is possible to replace the rubber bands on the janitors, then you can refuse to buy from the purchase of new brushes. If we consider that there is a lot of saidels, small particles of dirt and sand, to which in the winter is added in the winter, the gums on the janitors are very wearing and need to be replaced. The gums change very simply. The main thing is to determine the type of brush design, which is installed on the car.

How to change the gum on the janitors - the design of wipers

Currently used wipers 3 types:

• frameless;
• framework;
• hybrid.

Frameless wipers

They consist of a housing poured out of plastic with fused metal plates, between which a gum is installed. This type of janitor has a greater cost, they are not universal. Frameless wipers are manufactured for each car model individually.

Frame wipers

The greatest use was obtained on domestic and Soviet cars. All the details of the design until recently were made of metal, but now manufacturers are massively moving to plastic.

Frame wipers consist of:

• supports;
• rocker;
• hinges;
• adapter;
• gum;
• clamping plate.

Hybrid wipers

They use supports and rockers from frame brushes, and a plastic housing - from frameless. Hybrid wipers are very expensive and at the same time the most durable.

Which wipers can change the gum

Replace the gum without damaging the performance characteristics of the wiper can only be on the frame design. To replace the rubber components on hybrid and frameless janitars, a certain preparation and qualifications are needed. Such a replacement is made only in the absence of the possibility of acquiring a new set of janitors.

Procedure for replacing gum on janitor

Prepare pliers and a screwdriver with a wide blade.

• Remove the janitor with a leash. Gently, remove the screwdriver tape screwdriver. Flush to the minimum angle so that the gum will slip out of the janitor. Final bent make pliers. The fact is that the capture is wider, and the probability of damage to the clamps decreases.
• After feeding the tape from the support clamps, remove the plate from it, holding the gum in the curved state. Remember how the bends of the plates are directed to not confuse them. If you set them on the contrary, the gum will not be pressed against the glass, and the wipers will have to be dismissed.
• In the plates there are samples that include rubber tape grooves. This situation is possible when the thickness of the groove is greater than the sample width. In this case, take a thin outstimate and expand the sample.
• Insert the gum into the clamps. It must freely pass the locks. Pay attention, it is not allowed a strong backlash in the rockers, otherwise the new tape is quickly wear out.

How to protect the wiper brushes from premature wear

• Do not leave the car in the locations of direct sunlight. If this can not be avoided, then raise brushes from the windshield.
• In winter, the brushes do not face to the glass, lifted leashes and do not lower them until the car is heated. If the wipers are about it, then do not break them down with the power - the glass must hide with them.
• Strongly contaminated glass with branches and leaves must be pre-cleaned and wipe with a cloth so that the solids do not fall under the gum.
• Choosing the wipers, avoid dubious cheap fakes. Preference also give only proven or well-known manufacturers. Such products are characterized by good quality and made of reliable materials.
• Silicone rubber bands have proven well. They differ in durability and elasticity.

When carrying out such a repair, note that the quality of windshield cleaning will depend on how you follow the work. If a new gum skips some areas of glass, then you can repeat the experiment with the replacement, but it is better to buy a new set of wipers. Please note the cost of several rubber tapes damaged by poor-quality replacement, will block the cost of new janitors.

Sovetclub.ru.

How to disassemble a frameless janitor to replace rubber

Tags: car wipers

All rubber parts, namely, of such a material consists of the main working element of the glass equipment of the car, in conditions of constant influence of external factors (drops of temperature, ultraviolet of the Sun) quickly lose the work properties. Therefore, the blades of janitors or products are generally subject to replacement at least once a year, despite how much work they had to be fulfilled during this period.

In front of the many owners of the car, accustomed to the previous type of device in earlier models of cars, especially domestic, mounted glass cleaners, which were easier and clearer both in the disassembly and in their replacement, arises the question of how to change, if necessary, Elastic on wiper frameless design. Let's look at this question next.

Car wipers

Types of wiper for cars

On cars that are exploited now, you can meet three main types of janitors:

• based on the framework;
• frameless;
• mixed type (hybrid).

Frame glasses cleaners are more cumbersome, as they consist of a sufficiently large set of structural elements:

• clamping plates;
• rocker;
• adapter;
• supports;
• hinges;
• blades (gum).

Frame automotive wipers

In such janitor, which gradually move into the past, not only elastic bands are subject to wear, but also hinges, which relatively quickly fail. Therefore, after 2-3 replacements of the wear blade, it is necessary to change the entire framework wiper design. This is their disadvantage. However, there are advantages:

• low cost;
• simplicity of design;
• universality (interchangeability).

Frameless wipers have only an elastic metal plate with fasteners, which keeps cleansing glass gum. The devices of this type do not possess universality, that is, intended for a certain model of the car, the form of the overview glass of which they are perfectly repeated when moving. Holds a pressure plate in such glass cleaners plastic case, which transmits a force from the drive mechanism. Such wipers are more expensive than framework, both in general and at the cost of replacement gum.

See also: How to remove the rear bumper Jil Emgrand

Hybrid automotive wipers are the most durable, but at the same time the most expensive. Structurally, they are supplemented, compared with frameless janitor, supports and rockers, like those that have frame devices.

Frameless automotive wipers

Replacement of gum on ordinary wipers

First you need to remove the wiper from the lever. For this, the device is delayed from glass, carefully, without excessive effort. Now you need a janitor to turn to the floor turnover and separate. In some cases, there will have to do several revolutions (see the situation). We proceed to the disassembly:

1. The stubs on the sides are removed on the brush.
2. If there are spoilers, they should also be removed.
3. Remove the old elastic band from the groove.

It's time to put a new gum. There are two options here:

• show a new rubber part without disassembly;
• disassemble the frame and collect together with the blade.

In the first case, it should be easier to overcome friction, it is worth using any soapying solution, which should be lubricating the gum itself or the groove under it.

If there is no desire to engage in tedious pushing the rubber product, you can disassemble the brush, for which it is enough to remove one of the lateral metal plates. Then the gum carefully puts on the guide that remains on the brush. It remains to put a removal side plate, side plugs and spoilers. After installation, the rubber blade must be carefully understood that it takes the correct final form.

Replacement of rubber on janitor not having a frame

Wipers can be installed on different models of the car, a slightly different design, although they differ in principle slightly. Therefore, the method below with some reservations can be considered universal for frameless carpentry cleaners. After removing the janitors from the car, it is better to settle somewhere more comfortable at the table, taking with you:

• stationery knife;
• flat screwdriver with a thin but not sharp tip;
• soap solution;
• set of new rubber bands.

See also: What anticorrosion is better suitable for the car?

Now you can slowly begin to replace the suspended gum:

1. It is necessary to find from which side on the brush there is a locking cap, after which it needs to be carefully removed, going down the screwdriver. Here you need to correctly calculate the effort, since the cap holds on the clamps is quite firmly. However, when too strongly pressing it, it can burst, and separately it is not for sale.
2. We take out the served rubber, pulling it. She comes out almost no problem. Is that sometimes you have to bend the mustache, which are in the middle of the janitor;
3. To facilitate the insertion of a new gum in the middle, you should use something soap. It may be a shampoo or dishware. Soap mortar is abundantly lubricated guides and rubber parts are quite easily inserted into place.
4. In order for rubber insert to finally occupy its right place, the janitor can be slightly bent several times in the opposite direction.
5. An extra fragment of the rubber insert is cut down the edge of the holding of its design and is installed in the location of the plug.

As you can see, change the rubber band on the brush is not so difficult. Therefore, it is worth paying for half an hour a year to feel comfortable in the way with any "weather whims".

Okuzove.ru.

Car blind is appropriate only for participants of some TV show, on the urban streets, even minor dirt divorces on the windshield can hide, for example, a pedestrian, produced right on the road.

Even if you do not thwate the paint, you can say without stretching that car "wipers", or rather their condition, really affect the safety of motion. Even if you see everything, but the muddy of dirt glass makes you strain your eyesight, irritate from an unpleasant violin brushes on glass resulting in the inevitable fatigue, which reduces the speed of your reaction and affects driving safety.

The wipers are a consumables of the car, but the purchase of new ones is not cheap, but there is a way out - replacement of rubber brushes.

Therefore, "wipers" for someone who does not want to leave the road situation without proper controls, are consumable. But the price of high-quality products is quite high, and many prefer to change not the janitor, but the cleaner tape is "rubber band". How to change the elastic band on the janitor, which gums for janits are better to choose, as well as what brushes and ribbons for them are at all, we will tell below.

Types of windshield janners

Probably, not everyone was thinking about how uniformly fitting the working edge of the janitor's tape to the glass was carried out. But it is precisely a technical solution to this issue and caused the emergence of several types of brushes. We describe them by following the chronological order of changing the design.

Frame wipers

Frame wipers

As you can see, there is nothing particularly difficult in the design, but from the mobility of the sorcement of the frame during the work of the janitor, the way how tightly there will be a gum - the car is not flat, and the brush must "repeat" its form when the wiper operation must "repeat".

The design of frame janitors allows you to more accurately repeat the bending of the windshield and orient the rubber brushes perpendicular to the surface cleaned.

At the same time, the mobility of the joints of the rumor should not be excessive in the cross-moving brush direction, otherwise the janitor will "fall" the side of the side and will scratch the glass frame. In general, the edge of the gum should stand perpendicular to the glass - if it is not "stroking" it, but "goes to Zadira", then the "rubber" sound will be terrible, and the dirt will leave the strip on the glass. An elastic band is held at the rocker with steel plates, which must have sufficient elasticity and resistance to corrosion. Replacing rubber bands on frame janitars - a simple occupation, but requiring a certain skill. It is only necessary to pull out the gum along with the plates, and, reflecting the records in a new ribbon, to turn them into the grippers on the frame. Pay attention to payments at which longitudinal groove on the gum reference plates - the remaining grooves (folds) serve to collect dirt and ensure the elasticity of the working edge.

Winter frame wipers

Winter frame janitors allow winter to avoid freezing design elements, which is a certain advantage.

For such janitors, silicone gum are produced, which retain flexibility in the cold, sometimes they are called winter gums for janitors. Frame brushes themselves are available in the winter version - with a casing covering the hinges of the icing frame. It is the fact that frame brushes covering ice, stop pressing glass, and is their main disadvantage. As practice has shown, the hopes imposed on the winter version of the brushes were not justified - despite the high cost, these wipers did not lose the shortcomings inherent in their "summer" fellows.

Frameless wipers

As can be seen in the photo, such brushes do not have moving parts. The adjacent to the glass of such janitors ensures the elastic tape from the metal, which is actually the basis.

Frameless wipers

The main disadvantage of frameless janitors is a bad fit to the surface of the windshield, as a result of which the quality of cleaning is sharply reduced.

The big minus of these brushes - they are poorly adjacent to the most deployed stalks and are well coped with cleaning only if their manufacturer abused them to the concrete glass form, that is, they are not universal. Cheap Chinese products are practically not clean at all. The firms that are released, especially make focus on the fact that frameless wipers have good aerodynamics and are well pressed against the glass at high speeds. But their most important advantage is the lack of hinges that can lose mobility in icing. Replaceable gums for frameless janitors AVS look like this:

Replaceable gum for janitors

When replacing them, it is important not to "reverse" the basis - a metal plate. The violation of her form will cause a loose brush to glass and even if you buy good "branded" gums for janitors (Bosch, for example), the glass will not be cleaned properly, and the janitor itself will have to just throw away.

Hybrid wipers

Hybrid wipers

Hybrid wipers are undoubtedly a more modern product, providing comfort of use and quality of windshield cleaning, but they are not worthy.

In fact, it is frame winter brushes, but having a protective case separated by part. Such janitors on the conveyor are equipped with the most expensive models. Hinge rumors in them are protected from direct water from entering, but housing joints are freezing. Let such brushes and not completely delivered from the "diseases" characteristic of ordinary framework products, they still have a certain step forward. The biggest minus can be called their high cost - prices begin with 400 rubles.

The replacement of the elastic bands on hybrid janitans is performed almost the same as on ordinary frameworks. You can see how the gum changes for the hybrid janitors DENSO. The video demonstrates in detail in detail how to remove the old elastic band from the janitor and install a new one.

Choice of rubber brushes

If you have good dear brushes on your car, it does not matter - they are skew or hybrid - try to purchase "the same" rubber bands. That is, for the brusons DENSO, buy and rubber bands for the janitors of the company DENSO. The fact is that these products do not have any global standard and the installation dimensions on the brushes may not match, say, with a thickness of the gum, refilled in these mounts.

Choose replaceable rubber brushes of the same name of the manufacturer of janitors. So you can avoid not pleasant surprises because of non-docking in the sizes of the brush and the janitor.

True, many manufacturers produce ribbons for brushes to different cars, for example, you can purchase domestic gums for the janitors of Horse. In general, in the event that the "updated" wipers do not care about the glass, it cannot be said that some manufacturer "drives" a marriage, and find out which gums for janitors are better suited for your car, it will have to be experienced. Unfortunately, the sellers are not always conscientious of such trifles and can simply sell the wrong goods. One car owner who bought gum for Avantech janitors via the Internet, complained that he was just one tape with another label. In one of the rooms "behind the wheel" described how the editorial staff were selected wipers for cars. So they have achieved a positive result by installing the left and right of the wipers of various manufacturers, for which they had to purchase two pairs of the broths - they were sold by sets.

Sometimes car enthusiasts are interested - whether to restore gums on the janners. A broken gum for the janitor restore, of course, it is impossible, but here is a thorough cleaning of it from dirt with a solvent, will undoubtedly improve its performance.

With questions regarding how to change gums on janitor, I hope we figured out. In conclusion, you will present you company manufacturers (maybe and incomplete list) of the best gum for janitors available on the market: gums for VAN janitors; DENSO; Bosch; Avantech; Horse.

mYTOPGEAR.RU.

How to replace gums on janitor?

The wiper brushes are faster than all come to unsuitability, since they have to constantly interact with different climatic conditions, as well as mud and moisture. But when the first signs of faults appear, the entire mechanism is not rational, since it will be more practical to simply replace the gum on the wiper brushes. It is not difficult to do it, and we will tell about it in the article below. However, the deeper emphasis we want to make on how to protect the brushes from wear so that you can resort to replace as much as possible.

The main function of the wiper is cleaning the windshield of the car from dirt and moisture that falls on it. On some models, the windshield wipers are installed even on the rear window and headlights. The wiper brushes are very important for the safety of the driver and its passengers, due to which this mechanism should always be in good condition.

The process of cleaning the glass with wiper brushes occurs due to the swing movements that the brushes themselves perform. Removal of pollution and moisture occurs due to special gum, which are put on these brushes. They are the main part of the wiper, but it is most often wearing and requires replacement. If you purchased a new car, then it is necessary to take care of its wiper cleaners, which will help significantly extend their service life. After all, to replace the brushes every six months - the case is flawed both in moral and financially. In this regard, experienced motorists advise to comply with a number of recommendations for the proper operation of this mechanism that help extend its service life:

1. If you are going to clean the windshield of the car from dirt, then before this it must be mixed with water using the sprayer for this. If water ended in the tank, you can pour a glass of a bottle or to sketch a little snow on it. Thanks to the water, the movement of the rubber over the glass will be smooth, and it will not cause them damage. If this does not do, sand and dust that are on the glass can leave noticeable scratches on the rubber band, of which deep cracks may later. Of course, if you forget to pour the glass with water once, it will not cause the wear of the wiper gum, but if they are constantly incorrectly operated - the need to replace may occur very soon.

3. To winter under the influence of strong frosts of the gum of wipers did not appeal to the glass, they must be removed from the glass. And if this has already happened, no way to activate the wipers, as this is likely to cause their damage. And even a wiper motor can fail. But it is best for a wiper rubber, so that in the winter time the car is left in a heated garage.

4. Special attention during frost needs to be given and liquids used in the washer. So that it does not freeze, instead of it is recommended to pour non-freeze. Thus, after winter, wiper gums will remain in working condition, and their liquid tank.

5. It is harmful to wiper not only frost, but also very high temperatures, including the impact on the gum of direct sunlight. According to experts, under the influence of the Sun, the service life of these elements is reduced by about twice. For this reason, the gum must be constantly removed from the brushes so that after the summer they did not have to change. This procedure does not take much time, and with it we will introduce you a little lower.

6. To facilitate the load on the wipers, you can start a very simple habit: wipe the glasses during the refueling of the car or before you drive it out of the garage.

7. If frame janits are installed on your car, then you need to know that in such a mechanism, hinges come out. It is very important to prevent dust to fall on them. Hinge must constantly be lubricated by a special tool, otherwise they will quickly wear out, which will lead to the need to replace the entire mechanism.

8. Wipers cannot be used to handle snow. It must be removed by hand or scraper, and the glass can be dominated by janitors.

9. The same applies to the situation when ice crust is formed on the glass. In the interaction of elastic wiper with ice, very serious damage may appear on them. As a result, they will no longer be able to carry out high-quality glass cleaning.

10. Treat a very carefully to new wiper gums and be sure to buy high-quality products. This will also depend on their service life.

When is the need to replace the janitors and how to determine?

The first sign, according to which drivers determine the need to replace brushes - this is the quality of their work. However, it will not always testify to the wear of the gum: Sometimes the glass remains dirty due to the fact that the oil film is formed, with which the wipers are simply theoretically able to cope. The reason may also be hidden in improper fixation of the wiper mechanism. But let's consider in order to consider a number of most frequent signs that will indicate the fault of the wipers and the need to replace them (or replace the rubber bands):

After cleaning the glass, the janitor remains stripes. Most likely, gum scratched or born. As a result of wear and interaction with mud gum can lose the desired form. In this case, it must be replaced.

If the glass remains poorly wipe, the reason may be hidden in the deformation of the rubber or the optics of the wiper. Often this happens due to loss of rubber elasticity. To check how elastic it is, just remove it from the glass and release. If everything is normal, it should easily return to its original state. If this did not happen, it must be soaked in gasoline, rinse in soapy water and return to the place.

If, when you turn on the janitors, you hear outsiders, such as grinding, are most likely cracks appeared on the rubber parts of wiper. Try to restore a similar "malfunction" using silicone lubrication. If it does not help - gums are subject to replacement.

If the "radial" bands remain on the glass after using janitors, it means that dirt or corrosion accumulated on the rubber bands. Again, gasoline procedures and soching in warm water will return to them.

In general, it is impossible to determine the specific service life of the car of the vehicle. After all, different cars use different gums that are made from different types of rubber. If the rubber is natural - it is flawed faster, and it has to change it every six months. If artificial is the term of its service can reach up to the year.

2. What is needed to replace the rubber on the wiper brushes?

All you need to replace the gum on the janitors, it is:

Pliers;

Scissors;

New rubber bands for wiper brushes.

If you prepare the first three tools, you will definitely not be difficult, then with the purchase of new gum, many have problems. It's really not easy to make it, because for each model of the car you need to pick up your type of wipers. In addition, brushes need to choose such that they can combine at all combined qualities: flexibility and rigidity, hardness and softness. All this is basically concerned with rubber bands that dress on the bruthes of janitors and which are most often replaced.

Choosing new gum, it is very important that they come up for your wipers on the type of fastening. If the length does not correspond - it is nothing terrible, if necessary, it can be very easy to correct. But in any case, it is necessary to pay special attention to the quality of rubber:

Make sure that the product is in one color throughout its length;

There should be no bends and distortions on elastic bands, their form must fully correspond to the form of support of the wiper brush;

The cleaning side of the rubber band must be perfectly smooth, without mechanical damage;

A distinctive feature of high-quality rubber is its softness and elasticity (thanks to these qualities it will not break from the frost and it is less damaged when interacting with sand, dust and ice).

You should also not forget that high-quality products are not suiced. But, as you know, the miser pays twice. So it is better to leave a large amount in the auto shop and not return there for a whole year than every month to buy new gums for wiper brushes. Often in stores you can meet standard elastic bands from natural or artificial rubber. But recently, quite interesting variations have begun to appear that allow you to decorate the car:

Graphite gums presented only in black color;

Silicone, which are produced in different colors (more often occur white);

With teflon coating that differ in the presence of yellow strips (considered more wear-resistant);

Rubber-granite mixture.

As you can see, you can choose any option for any car. The main thing is that the product is distinguished by quality, and was also correctly installed. Otherwise, repeated replacement may be needed in a couple of days.

3. What is the process of replacing rubber on car windscreens brushes?

The replacement process is the task even less complicated than the choice of new gum. Each auto owner at home can perform it, spending on the entire procedure no more than half an hour:

1. Raise the levers of the janitors of the car, that is, we take them to the side from the windshield.

2. Remove the old gum from the supports, which have already come to unsuitability. Using pliers, it is necessary to remove their mount on the guide levers of the windows brushes. To do this, we simply flex a two or three millimeter clips and get the rubber band. The main thing is not to overdo it with the clips, since they are very fragile and can easily break.

3. The gums are removed along with the ribs on which they are attached during the work process. By the way, when buying a rubber band, these ribs can also be included with them. In this case, the old can be thrown away, but if there are no new in the kit - you have to use them.

4. Compare a new and old elastic band. They must match each other in size. If the new is a little more, it is necessary to level with scissors or knives.

5. In the same grooves in which the old elastic band was mounted, insert a new one and fix it with the help of the clips. At the same place we install the ribs of wipers. This replacement is completed. It remains only to rinse the wipers and lubricate the entire device mechanism. Thanks to this, the updated wipers will work simply and without interruption, providing maximum returns from new rubber bands and their proper operation.

Subscribe to our ribbons on Facebook, VKontakte and Instagram: All the most interesting car events in one place.

Was this article useful?

aUTO.Today.

Replacement of rubber bands on frameless janitor

The fact that the wiper brushes periodically must be changed, everyone knows all the motorists. However, there is an alternative to the replacement of only rubber cleaner tape. What are the advantages and what disadvantages of this method, when he can be justified, let's talk about this in this article.

Why change gums on frameless janitor

When your wiper brushes cease to cope with their direct duties for cleaning windshield, leave stripes, crude areas should be thought about to replace them. However, there is an alternative to replace the rubber cleaner tape in the janitor. Most often, the main reasons for which car owners are resolved to replace the cleaning ribbon on a frameless brush, and not the whole janitor, the following:

• the desire to save - even the cheapest Chinese frameless brushes (with unknown quality), as a rule, are more expensive than a good cleaning tape;
• rare brush. Rare brush fastening, size, lack of suppliers, long delivery time and the like. This is the second most popular reason for replacing rubber bands.

If the brush frame itself is generally suitable for operation, not lost mobility, the steel brush element provides the necessary clamp to the glass, then replace the gum in such a janitor is quite acceptable.

Gum for frameless janitors

Separately, it is replaceable rubber tapes for wiper brushes for sale by many manufacturers. There are such products in the Bosch, Champion catalogs, offers its branded removable gum with Maruenu tourmaline, there are replaceable ribbons from Alca, SCT and Horse. The gums are sold different lengths, pieces, sets of 2 pieces, and in some stores even began to sell a cleaner tape in the bays on meters. How much you need so much and cut off.

Gum from Horsa Replaceable tape SWF.

But the manufacturer's choice is not the only important point when selecting gum for a frameless brush. It is important to draw attention to the ribbon profile and even width. Most often in frameless brushes, a rectangular 6 millimeters width profile is used, but there are other options. There is a profile in the form of a trapezium, it happens in the brushes using a gum width not 6, but 8 millimeters.

Profile and size of gum for frameless janitors

How to disassemble a frameless janitor

Disassemble a frameless brush and change the gum in it is simple enough and everything can be done with your own hands. To do this, you need:

• flat screwdriver;
• cleaning tape for replacement;
• passatia;
• scissors.

Now actually the algorithm algorithm disassembly and tape replacement.

We hope that you understand how to disassemble the frameless janitor and change the gum. If you have any questions, watch the video or ask them in the comments to the article.

The wipers of the car have a great influence on a comfortable ride. Their work provides good visibility of the carriageway and allows the driver to keep the car suspension, circling irregularities on the road. And the better the quality of the janitor's work, the more the driver and nerves of the driver. If the work of the janitors is unsatisfactory - they must be replaced. Replacing the rubber on the wiper brushes must be fully responsible. In this article, I will tell you how to make a gum on the janitor to operate as long as possible, and their work was positive.

Not every driver wants to change the brushes of janitors every six months. Therefore, for this it is necessary to monitor their condition and perform some requirements for their operation.

• Before turning on the cleaning of windshield, it is necessary to start it with the water from the sprayer. If the keg is empty, you can use a plastic eggmarket or snow. The movement of the dry glass gum can provoke their damage. On the windshield a lot of dust and sand, especially on the rear window. When the dry rubber band passes along it, threads and cracks can be formed on its surface. Of course, this happens not after once, but this is a fact.
• From time to time, the janitor must be lubricated or washed with water. And this applies not only to the mechanism, but also the gum should sometimes get the proportion of the lubricant.
• In winter, special care is needed. If you leave the car for an indefinite open-air period (not in the warm garage), then you need to divert the wipers from the windshield. With severe frosts, rubber bands are about glass. And if at this time you will need to use the car, then do not try to turn on the cleaning of the glass. This can lead to premature wear of the motor and brushes.
• At the occurrence of cold weather, it is necessary to replace fluid for the washer to the anti-massarmecot. This will allow not only to save the wipers for another seasons, but also save you a tank for fluid. Since the usual fluid freezes and leads to crackling the tank.
• High air temperature and direct sunlight on the brushes double reduces their service life. If you do not want to buy new brushes after the summer, do not be lazy to remove them from the car. The removal procedure will take you a couple of minutes and save you several hundred rubles.
• You can get a habit - wipe the glass while refueling the car or every time they use it.
• The most vulnerable part of janitors (frame) - hinges. Behind them should be followed. When dust hit on them, their corrosion and premature wear arise. Hinges need to be lubricated with any means. Otherwise, the wiper will have to change.
• It is not recommended to use a janitor when a layer of snow is present on the windshield. It is better to sleep with hand or scraper. And only after that, turn on the janitor to perform the cleaning of the wet glass.
• Do not turn on the janitor when the glass is covered with ice layer. The friction of rubber in people will lead to the appearance of cracks and cuts, and this, in turn, is to poorly clean the front or rear windows.
• Before buying new items, pay attention to their condition. Carefully check their surface for damage. Remember than the wipers are cheaper, the better their quality of work is worse. It is better to pay once, but pass with normal wiper not one year.

Replacing rubber bands on wiper

Even if you have never done this, it will not be difficult to remove them.

It is important to take into account that there are three types of janitors and several types of fasteners with which the rubber band is attached to the base (edges). Prepare the necessary tool - pliers, knife and scissors.

The replacement of the gum on the janitors is performed quite simply and does not take much time.

So, the replacement is done like this:

1. Wiper levers need to be raised (remove from windshield).
2. Next you need to launch old worn gum. To do this, we find their place of attachment to the guide levers and disconnect with the help of pliers. It is important not to overdo the clamps. They need to be bent into several millimeters (2-3). Otherwise, they can be damaged.
3. Each gum is disconnected along with the edge on which it is located. Some sets include not only gum, but also these ribs. If they are undoubtedly use them. If not - use old.
4. New gum must match the size of the old. Therefore, if necessary, cut it into size.
5. The new item is inserted into place of the old (in the grooves) after which the mount is fixed. Ribs are installed in the same place.

Since I had to replace the wipers, you can at the same time lubricate the entire mechanism or rinse with it with clean water. You can make a comfortable ride on the car. To do this, it is enough to establish normal wiper.

Video "

The record shows one of the ways to extend the life of janitors. Check out the video and learn how to change your own elastic bands on them.