If you are one of the summer residents who take the issue of caring for their garden and garden seriously, then you probably cannot imagine your life without a walk-behind tractor. If up to this point you have coped with your tasks using other equipment, then you should think about purchasing the above-mentioned device.
With its help, you can cultivate the land, and your health will not suffer. Undoubtedly, this equipment is quite expensive, but it has so many functions that it will justify the purchase in just a year. The main task of walk-behind tractors is land work; this equipment will allow you to plow, hill and cut rows. In addition, the walk-behind tractor can help a person take care of the lawn. For this purpose, a kit is supplied that cuts the grass like a trimmer, covering about a meter of lawn.
If you additionally purchase an aerator attachment, the lawn will receive additional oxygen supply, which means the grass will be thicker. Now that you are familiar with all the advantages of the equipment described, you should pay attention to the manufacturers. Among other models, you can find the Tarpan walk-behind tractor on the market for relevant products, which will be discussed below.
Description of the walk-behind tractor brand "Tarpan Zongshen"
This equipment is not so expensive, the price is 27,300 rubles, but by paying, you will receive a device that is used for cultivating soil in gardening conditions. It is powered by a four-stroke engine with a power of 5.5 liters. With. The engine is equipped with an oil level sensor. The manufacturer took care of ease of use by equipping the Tarpan walk-behind tractor with wheels with a special tread pattern that guarantees high maneuverability.
Using the unit, you can use one of two speeds, which contributes to better maneuverability. The height of the walk-behind tractor can be adjusted using the handle; the height position will ensure convenient operation of the unit. If necessary, you can additionally purchase attachments, which will become effective equipment. But the presence of a power take-off shaft means that you can use an active hitch.
Main technical characteristics
The Tarpan walk-behind tractor described in the article, the price of which may seem quite impressive, has unique technical characteristics. The equipment has a built-in Zongshen 168 FA engine, and the plowing width is 70 cm. Power is transmitted to active attachments via a power take-off shaft. The engine capacity is 163 cm 3, and the diameter of the cutters is 32 cm. The clutch is belt driven; there is no electric start in the equipment. The power of the unit is 4.1 kW, and horsepower this value is 5.5. Using this Tarpan walk-behind tractor, you can go 20 cm deep into the ground, the device weighs 75 kg, it is equipped with Gas engine, the fuel tank volume is 3.6 liters. The manufacturer equipped the device with a gear type gearbox.
Key Features
Considering the features of the walk-behind tractor, we can highlight:
- excellent maneuverability;
- comfortable control;
- ease of refilling.
As for the first characteristic, it is ensured thanks to big wheels, because a tread with an aggressive pattern will go over any surface, even if the landscape is not level. The handle of the walk-behind tractor allows for comfortable control; it can be adjusted, which makes operation convenient. Fuel tank The walk-behind tractor is located in an easily accessible place, so in a matter of seconds you can refuel the tank. Its neck is wide enough, which makes the process easier.
Main advantages
The Tarpan walk-behind tractor described in the article has many advantages, among them we should highlight reliable engine, the presence of a power take-off shaft, as well as a wide range of attachments. For better maneuverability, the manufacturer has equipped the device with a reverse function; in addition, you can even adjust the plowing depth. You should not be afraid that the walk-behind tractor will not cope with clay soil, because it is equipped with a powerful engine that will be able to handle such work.
Cost of attachments
If you are interested in Tarpan brand products, you may have to additionally purchase attachments for motor cultivators. For example, a hiller, which is used with the Tarpan 03 and Tarpan 04 models, can be purchased for 940 rubles. Whereas a frame with transport wheels will cost the consumer 1,033 rubles.
Sometimes buyers are also interested in lugs. If their size is 260 x 80 mm, then you will have to pay 1,480 rubles for the set. With dimensions of 400 x 170 and 500 x 170 mm, lugs will cost 1,790 rubles. Attachments for motor cultivators are also potato diggers, which cost 624 rubles. will cost 1,100 rubles, and the weeders, or rather a set of them, will cost 1,160 rubles. A walk-behind universal hitch used to attach to a walk-behind tractor costs 2,100 rubles, a houndstooth cutter costs 2,880 rubles.
- this is not only a breed of wild horse that no longer exists on our land. That's what they call it domestic cultivators, which are used to cultivate land up to five to twenty acres.
They are popular among users due to their reliability and powerful motors from American and European manufacturers.
About the manufacturer
This model was invented by Tula engineers in 1991 as a simple and reliable replacement for the Rus walk-behind tractor, which was produced by Tulamashzavod.
At first, Tarpan was unprofitable, it was not in great demand, but after it was improved and equipped with productive engine from Briggs&Stratton things got much better. Since 1997, cultivators have been put into mass production.
Today it is manufactured by the specialized company Tarpan, which is subsidiary company"Tulamashzavod", which is located in the historical center - Frolovskaya Sloboda, which is famous for its specialists.
On the ground that belongs today legal entity, in 79 of the nineteenth century the Baitsurovsky plant was built, which produced various cast iron and copper products.
Tulamashzavod - famous company, which specializes in mechanical engineering.
The enterprise includes production facilities that are equipped with new equipment and leading technologies. All necessary information you can find it on the official website tar-pan.ru.
Production includes: procurement workshops, galvanizing and processing high temperatures, production of tools, parts, wood processing.
Along with classical equipment, automatic and semi-automatic devices, which allow you to run the program in dialog mode. This ensures high technological flexibility of production.
Often used to reduce preparation time end-to-end automatic design of elements and equipment(from external indicators to creating control programs for machine tools).
For more information about the Tarpan cultivator, watch the video:
Popular models
The first motor-cultivator from the Tarpan series with two-stroke engine productivity 6.2 hp was released from the assembly line in 93. It immediately established itself on the market with positive side, but due to some production shortcomings it was not so popular among farmers.
03
Thanks to the work of engineers, a few years later domestic marketpresented the Tarpan-03 model. To this day it has not lost its leading position in the Russian market– consumers buy up to a thousand of these cultivators every day.
The plant's engineers have added various attachments to the model, which can be used regardless of the year: for winter you can use a snow blower rotary type, while its working width will be 75 cm. It throws snow up to 5 meters; you can also purchase an ice breaker to clear the path.
Regardless of the time of year, with the cultivators Tarpan, Mantis, Cayman, Viking, Texas, Swift, Champion, Patriot, Loplosh, you can carry out all gardening work using a plow, rotary cutter (included), hiller, flat cutter, rake to crush and level the soil, collect for weeds and other attachments.
The cultivator can be used as a lawn mower, and in the fall you can dig up root crops and prepare the soil for winter.
The operating life of the motor is 1000 hours. The automatic centrifugal clutch allows the model to be disassembled into several devices, which can be easily transported and stored.
Thanks to the worm gearbox, you can eliminate the unreliable belt and chain drives that are installed on the walk-behind tractor.
Thanks to the improved design of the steering rod, the steering wheel can be rotated both in a lying and standing plane, thanks to which the operator will walk to the side of the unit, while the loosened soil is not trampled.
Specifications:
- Engine: Briggs and Stratton I/S 6.0 l. With.
- Motor performance: 6.0 hp at 3600 rpm.
- Cylinder volume: 190 cm3.
- Constant air cooling.
- Starts with manual start.
- There is only one transmission.
- Fuel tank volume: 3.8 l.
- Engine oil volume: 0.6 l.
- Fuel consumption: 1.5 l/h.
- Power: 0.06 Ha/h.
- Milling cutter maximum speed: 100-120 rpm.
- Cultivation width: 350-700 mm and depth 200 mm.
- Parameters (length/width/height): 130 (76)/70/106 (75) cm.
- Weight: 45 thousand grams.
- Price: 18 thousand rubles.
Detailed video about this model.
Realizing that you can confidently conduct and develop business in conditions modern market, which is constantly changing, it is necessary to produce high-quality, competitive, reliable and affordable equipment; the manufacturer annually updates its model range produced from assembly lines.
031, 04, 07
IN last years Near basic models 031, 04, 07 models of motor cultivators were produced.
Specifications:
- Motor power: 5 hp
- Motor type: single-cylinder 4-stroke, top-type shaft.
- Clutch type: automatic, centrifugal, dry.
- This Tarpan cultivator has a worm and single-stage gearbox.
- Gears: 1, forward.
- Hot mixture: gasoline.
- Clutch: centrifugal clutch.
- Processing width and depth: 360 x 200 mm.
- Weight 28 thousand grams.
- Price: 11 thousand rubles.
04
Compact model for a medium-sized plot, like a mini cultivator for a summer residence, it is equipped with a pair of wheels so that the cultivator moves during operation and a coulter, thanks to which the depth of travel of the cutter is adjusted.
“Tarpan-04” is very easy to operate; it has only one gas lever and a “Stop” button.
The main highlight of this model is its relatively powerful motor for medium areas. Thanks to this motor, as well as low turnover cutters (100-120 per minute), the model will ideally dig up the soil onto the “bayonet of a shovel”.
A productive and affordable electric cultivator in an affordable price segment.
Specifications:
- Motor: Briggs & Stratton (USA).
- Engine type: single-cylinder, 4-stroke carburetor type.
- Performance: 6.0.
- Runs on: gasoline.
- One gear, no reverse.
- Weight, g: 45 thousand.
- Max. processing depth, cm: 20.
- Parameters, cm: 135 x 60 x 110.
- Price: 26 thousand rubles.
07-01
Manual
It is important not to use the unit for several days after purchase. full power– you must remember that the device must be run-in for the first 24 hours. Therefore, it is better to process the same bed in several stages, each time increasing the depth of processing.
Start
Before launch it is worth check oil level, the engine is working properly, whether the power unit is securely attached to another unit that performs an additional function.
Starting the engine when the control lever is clamped (the engine speed control position is “fast”) is prohibited, because the device’s clutch works automatically when the engine reaches the desired speed, which is more than the idle speed.
Soil treatment
You need to stand near the steering wheel and hold the handle tightly. Do not press the lever too hard, slightly increase the engine speed.
When the motor reaches the required speed, it will automatically work centrifugal clutch, and the gearbox shaft will begin to rotate.
At this time the device will begin to move. Deep processing of soil with milling cutters determined by the position of the depth regulator, which may change when rearranging it in the bracket along the holes that are in the regulator.
Turn off device
To do this, lower the control lever. It will return to its original position on its own. idle move as a result of the operation of the return spring. Then pull it down all the way and the motor will stop working.
Malfunctions and repairs
"Tarpan" cultivator, the instruction manual indicates some causes of breakdowns. Motor impossible to start or occurs with difficulty. This may occur due to a misconfigured engine speed controller, or fuel is not supplied to the carburetor.
To resolve this problem you need to:
- Check the presence of fuel in the tank.
- Check spark plug gap.
- If necessary, clean the spark plug from carbon deposits or replace it.
- Check the carburetor for proper operation.
The motor may also overheat.
It starts to overheat because the cooling system and air filter are clogged.
In order for the engine to operate at normal temperature, the cooling system and air filter must be cleaned or replaced.
The engine does not operate at maximum speed. This often happens because air filters clogged and are subject to replacement. To eliminate this problem, you need to clean or replace the filter.
Malfunctions often occur due to the operator’s fault due to irrational use of equipment, so be sure to read the instructions before starting work. If you have not saved the original, it can be found on the Internet, in one of search engines write: “Tarpan cultivator instruction manual.”
The Tarpan model range is constantly updated and improved in terms of its technical characteristics.
Conclusion
The main feature of cultivators is quite productive motor, in comparison with other models of this type. The only negative model range: No reverse gear.
People growing crops on their property almost always use
The Tarpan motor-cultivator can be classified as middle class, single-operational, with one speed. It is equipped with a B&S engine with a power of 6 hp. Adjustable cutter grip 35/70/100 cm. Also installed worm gear and automatic centrifugal clutch. The weight of the walk-behind tractor is 45 kg. It does not have reverse gear and power take-off.
Is it worth buying a Tarpan motor cultivator?
To roll the walk-behind tractor, two wheels are installed. And in order to regulate the depth of travel of the cutter, a coulter is installed. The walk-behind tractor itself can be easily disassembled into two parts. The wheels and handles are made removable. Thanks to this, it easily fits into the trunk of a car.
The main feature of Tarpan is quite powerful engine, compared to other motor cultivators of this class. Unfortunately, the designers did not provide reverse gear, which is a big disadvantage. Worm gear The gearbox was installed in a fairly robust housing.
Unfortunately, it does not have a reverse motion due to the large gear ratio. When cultivating heavily planted areas, you often have to pull out the cultivator in reverse. This usually happens in places where turning around is not possible.
In this case, the cutter does not turn back, it skids and turns around what was just loosened. It is for this reason that modern motor cultivators are equipped with gearboxes with gears either with chain drives. If a worm gear is installed, then only with reverse gear.
Therefore, Tarpan is very convenient for owners of open gardens, and for those who will prepare the soil for further cultivation and sowing. In this case, for ease of control of the walk-behind tractor in reverse gear there is no great need.
Traction and speed of the Tarpan motor cultivator
The following design features of the motor cultivator are an automatic centrifugal clutch and a detachable “leg”. This allows you to disassemble it into two parts and put it in the trunk of a car, which is a definite plus. On the other hand, thanks to this feature, the clutch “often falls out” when working with a hiller, plow, or digger. If you use an automatic clutch, it has a large actuation inertia, which is unsafe.
To turn on the speed and start the cutter, you need to turn the gas lever. This will lead to an increase in speed, after which the cutter begins to rotate. If it is necessary to stop the cutter urgently, the operator must remove the gas. This will not immediately turn off the cutter, and it will continue to work for some time. In this case, you need to use the “Stop” button.
Also used in the structure of the motor cultivator new design steering rod, which allows you to rotate it 360 degrees and adjust the angle of inclination. Thanks to this, the operator can walk next to the motor cultivator, and not along cut furrows or loosened soil.
If you install optional equipment on a Tarpan motor cultivator, it will be able to weed, hill, harrow, loosen, mill, etc.
Motor cultivator Tarpan reviews
Vladimir, a resident of Belgorod, uses a Tarpan motor cultivator at his summer cottage:
I have been using Tarpan for 9 years now. Positive general impressions primarily thanks to the engine. Advantages of a motor cultivator: it always starts at half a pound; because it's worth four stroke engine, no need to cool the oil, just fill it with gasoline and change it a few times a year; Easily fits into the trunk of any car because it can be disassembled into two halves. Disadvantages of Tarpan: the gas is made very awkwardly - under the thumb of the right hand. He gets tired quickly.
Review from Sergey, a resident of Omsk, uses the Tarpan Motor Cultivator on his site:
With its light weight (48 kg) and “monstrously” excess power, it is difficult to take on virgin soil. If you first use a tractor plow to break up the roots, the lumps will be dealt with easily and simply. Due to the design features, reverse is not installed. But with its light weight, it can be deployed manually without any problems. I saw a cart being pulled by a converted Tarpan. The plow doesn't pull because it's light weight. And at the same time, it perfectly cuts the beds with a hiller on cutters. Excellent material from which the cutters are made.
Review by Andrey Ivanovich, a resident of Rostov, uses a Tarpan motor cultivator in a greenhouse:
I sharpened them once after purchasing them and never touched them again. I mainly use a hiller and cutters - I’ll cut the beds, plow them and that’s it. You need negligible gasoline: a 1.5-liter tank is enough for an hour of work. The first time I removed the cutter casing, because it only got in the way, because a lot of grass gets wrapped around the cutters. I also hung a 20 kg weight in front, thanks to which the virgin soil was taken much better. But it was dangling from the front and rocking the cultivator.
In general, if you use it for country work with a minimum of settings and hassles, this is quite a convenient thing. Also, we must not forget that the cultivator’s first task is to loosen the soil, which it does just fine. Therefore, only cutters come with it. 
Review by Roman Viktorovich, a resident of Kharkov, uses a Tarpan motor cultivator at his dacha:
I have been working with Tarpan since 2004. Very satisfied. If, when working on heavy ground, he begins to jump and tries to escape, then first you need to remove and sharpen the knives. It is advisable to attach a weight. I made a weight from lead (melted down old batteries). The resulting load weighs 13 kg, has a compact volume and allows for excellent work. It can also be made in the form of several plates to regulate the weight. I use the load for digging trenches, virgin lands and primary plowing. Then I take it off and it works great.
Alexey, a resident of Kharkov, uses Tarpan in his personal plot:
I just recently purchased Tarpan. Yesterday I went through the garden using cutters. Feelings: the engine runs vibration-free and quiet; the cultivator is a little light and sometimes bounces; cultivated perfectly the second time, when I turned the horns, there were no traces left. Processed seven acres. It took two hours and three liters of gasoline.
Vladimir Ivanovich, a resident of Belgorod, uses a motorized cultivator at his dacha:
The load on the back and arms is acceptable. Apart from cutters, I did not test any attachments. The cutters have to be cleaned because the roots get wrapped up a lot. But I think this is a plus, since it removes weeds from the garden. If the cutters are sharp, they will cut the roots, after which weeds will multiply.
Motor cultivator Tarpan video compilation
Plow for motor cultivator Tarpan
High-strength special steel was used to make the plow for the Tarpan motor cultivator so that it could withstand heavy loads. Its purpose is to plow the soil complete with lugs, thanks to which the required traction force is created.
The use of a plow is possible for initial tillage. For loosening large clods land, cultivation is necessary.
There are not many models of motor cultivators produced on the Russian market. Therefore, after appearing motor cultivator Tarpan-03 Many people turned their attention to him. This is a fairly powerful and versatile tool that can be used without problems anywhere in the vast homeland. And it’s not just that the device can withstand various climatic conditions, but also in the particularities of its characteristics.
Design of the Tarpan TMZ-MK-03 motor cultivator
The Tarpan-03 motor cultivator has modular design, which allows it not to be stored in a summer cottage, but transported from home to own car putting it in the trunk. This is achieved thanks to not only replaceable attachments, but also a removable American-made engine. It is semi-professional and contains only 1 cylinder in its design. The engine of the Tarpan-03 motor-cultivator is a 4-stroke engine, which allows it to develop power up to 6 hp, and its service life is within 1000 operating hours.
There are other modifications that are equipped with engines Japanese made With less power(total 5.5 hp).
To transmit power to the working parts, a worm gearbox is used, which has a large margin of reliability compared to belt and chain drives, which extends the life of the Tarpan-03 motor cultivator. Its design is located inside an oil bath. But, despite all its advantages, it has only one speed.
The working width may vary depending on the attachment used. IN standard it is 750 mm. When using an additional canopy, it can be increased to 1 m. Similar equipment is used:
- Lawnmowers;
- Rake;
- Hillers;
- Rotary cutters;
- Plows;
- Flat cutters;
- Ice crushers.
As for rotary snow blowers, they can also be used. In this case, the snow throw range can reach 5 m.
The total weight of the structure is 45 kg. Thanks to this, operating the device is quite simple. This is also facilitated by the adjustable length and height of the handlebars.
Fuel consumption of the Tarpan-03 cultivator
Also check out these articles
Despite the relatively high power engine of the Tarpan-03 motor-cultivator, it consumes a little - a lot, but 1.5 liters of fuel per hour. At average load this figure can be reduced to 1.1 l/h. Taking into account the volume of the fuel tank at maximum power It can be used powerfully for 2.5 hours without additional refilling. Regular gasoline is used as fuel for this model of motor cultivator.
Technical characteristics of the Tarpan TMZ-MK-03 cultivator
- Engine Manufacturer - Briggs
- Engine - gasoline 4-stroke - "B&S" Qvantum - (USA);
- Engine power - 6.0 hp;
- Clutch - dry, automatic, centrifugal;
- Gearbox - single-speed, worm in an oil bath;
- Maximum processing depth - 200 mm;
- Working width - 350, 700, 1000 mm;
- Fuel consumption - at max. load 1.1 l/hour;
- Productivity - 0.06 ha/hour;
- Overall dimensions (control handles folded) - 1300x700x1060 mm;
- Weight - 45 kg;
Video about the Tarpan TMZ-MK-03 motor cultivator
