When updating the interior of the cabin, you need to know how to pull the car seats with your own hands. This operation begins a complete renovation of the interior. The procedure is not too simple, but leaving the seats as they are is not an option at all. Old material will spoil the whole impression of the car. Therefore, you will have to take on this work.

To do everything as correctly as possible, you need a high-quality sewing machine and tailor skills. Otherwise, the hauling work is not difficult, and can be performed in any garage, which makes it pointless to contact a car service for this.

How to pull the car seats with your own hands? In theory, every motorist should know. After all, there are a lot of cases when it is necessary. With this skill, you can significantly save on visiting the service.

Materials (edit)

Work begins on the seat hauling with the selection of materials. To begin with, it is advisable to decide what kind of salon you want. Now in stores, motorists are offered the following options:

• Leather... Great stuff. It will give your car a self-contained look. The disadvantage is the tendency to attract the sun's rays. As a result, the sun will be very hot in the cabin;
• Suede leather... This material is very pleasant to the touch. Its disadvantage can be called a tendency to pollution, it is also quite expensive;
• Alcantara Is an artificial suede. It differs little from the suede itself, this allows the use of Alcantara as a substitute. The main advantage is low cost;
• Velours... Great fabric, just perfect for car upholstery.

The last 2 options are most often used. Car enthusiasts are attracted by the low cost and excellent appearance. The color is usually selected based on the overall interior color. This will allow you to make the interior as pleasing to the eye as possible. But, there may be exceptions, it all depends on your tastes and preferences.

Preparation

The seat re-tightening process can be divided into several stages. One of the important episodes is preparation for the main actions:

• Removing the seats... On some car models, this is a tricky business. Therefore, before work, clarify all the features in the manuals. Particular attention should be paid to dismantling heated seats. Be sure to turn off the power,;
• Use a marker to mark the parts of the old cover. Please note that sometimes the driver's and passenger's seat may be different. The easiest way is to fit the rear seats;
• The cover is removed from the chair. Be sure to remember the position of the fasteners. Sometimes various hooks are used, the best option would be to use them when pulling on a new sheathing;
• Carefully cut the cover along the seams. Use the resulting pieces instead of the template.

Padding

After completing the preparatory steps, you can proceed to the tug itself:

• We start by cutting out the material. To do this, we take the prepared patterns and put them on the fabric. You need to carefully straighten them. For this, weights are laid out in the corners. Do not forget to leave a seam allowance, 5 cm is enough. When cutting Alcantara, it is important to take into account the direction of the pile, otherwise the seat will turn out from several different shades. After marking, iron the fabric;
• Cut the material carefully;
• Foam rubber is glued to the back of the fabric. For this, a special glue is useful, it is usually sold in cans;
• Perhaps the most important point is the stitching of the blanks. To do this, you need to be able to use a sewing machine. The slightest mistake can lead to the need to start over;
• The cuffs of the seams are glued. It is also important to beat off the seams with a hammer, this will give them additional flexibility;
• After that, the cuffs are stitched again, with a double stitch, the excess fabric is cut off;
• Most of the seat covers are secured with straps or hooks. Sew them in the same way as they were on the old casing;
• They start pulling from the backs, after which they move to the seat. Stretching the fabric completely, fix the cover on the chair.

After all the work, it remains to complete the process with a few strokes. The leather seats are dried with a hairdryer. But, do not overheat, do it as carefully as possible. You need to warm up the seat at a moderate temperature, until the material is stretched. Fabric materials are cleaned of traces of glue, as well as other contaminants.

Conclusion... The car interior is used quite intensively. At the same time, gradually its casing wears out, and its replacement is required. That's when the car enthusiast has the question of how to pull the car seats with his own hands. After all, this is the easiest way to solve the problem. This is not difficult to do. A minimum of skills and tools are required to work.