The first option requires the improvement of the fuel supply system by mechanical node, namely the carburetor:

1. You need to install a throttle or diffuser of more updated models.
2. You should carefully remove the springs in the primary chamber on the throttle drive.

This kind of tuning of the carburetor significantly increases the air flow, allows the engine to "breathe", significantly increases its characteristics of the speakers and power.

The second option provides for the acquisition and installation of a special block - controller. This device is a carrier of software. Thanks to this, it is possible to increase the power indicators, torque and, of course, the dynamics.

Exercise tuning suspension VAZ-21099

Update the suspension of the vase is necessary according to many lovers of auto scheme known to many:

• high-quality installation of two-section shock absorbers;
• production of replacement of transverse type stabilizers;
• installing updated brake discs;
• installation of an updated hub;
• the product of the replacement of hinges for spherical;
• conducting a suspension lifting procedure by establishing advanced springs.

Salon tuning for VAZ-21099

This procedure conventionally consists of two stages:

1. Replacing seats for new / work of modernization of regular front. For example, summing up the heating system, tosing a high-quality modern cloth.
2. Refreshing the cabin. Such innovations are easy to produce independently or by purchasing a new set in the ready-made form.
3. Installation of figured carbon inserts (you can choose wooden, plastic, chromed, etc.) on the side panels of the car doors. Thanks to this, the car inside will look more representative and elegant.

Finally, one hundred IT to draw the attention of readers to the fact that the work of tuning salon VAZ-21099 is more creative process, rather than technical. Here you will need to show a lot of patience, accuracy and accuracy in decisions, in order to get a high-quality tuning that can make a proper impression on the most owner of the car and in foreign people.

As always, we will start our tuning from the most important element of any car.

Engine tuning

Most domestic machines have a lot of flaws that reduce the power of the engine and the chassis. So, for example, the thermostat can work perfectly while driving a cooling of the engine, but as soon as the heating system is turned on, work, this device immediately comes out from under control. At the same time, there are problems with the overheating of the engine, full failure of the car or wear parts. The thermostat can be adjusted slightly, having previously understood due to such a problem. In the heating system in the included state, mixing the heating fluid and the coolant is made due to the cooling level in the thermostat drops. Especially strongly affects the offensive of frosts when the cooling fluid is already lowered to the bottom of the tank. The best option will be the installation of the nozzle where the thermal element in the thermostat is located. In addition, it will be necessary to close the hole in the water pump. This is allowed to control the incoming fluid when the heating system is turned on. After these changes, it can be noted that even at elevated salon temperatures, the degree in the engine will not exceed 78C, and this is optimal for its operation.

In production, it is often possible to replace how marriage is allowed when installing the generator belt, or simply speaking, timing. This makes the engine less powerful, as well as largely reduces the safety of the ride. In order to correct this problem, you need to replace the belt new, while you can do your own work. The main thing is to prevent a common error when the belt is bend or twisted, which significantly reduces its service life. At the beginning of work, before removing the generator belt, you need to remove all the details that prevent it from dismantling. This steering pump, belt pulleys and air filter. After this procedure, the generator belt, removed, pre-promoting two bolts, which hold it, and work is carried out in the reverse order already when installing a new part. It is recommended to work only with knowledge of the case in order not to damage the crankshaft mechanism during the removal of the timing belt.

Aza mechanical tuning

To improve the engine dynamics, many produce a variety of modernization of a particular part. So, for example, in the "nine" engine, drivers often replace the sleeves of the valves. New bushings have many advantages. The first to what you need to pay attention to their lightweight weight and polished housing, and this makes wear out this spare part not so fast. Lightweight weight eliminates the valve from hanging, which allows the power from the engine and high revs without interruptions in the engine operation. Engine power increases due to improved cylinder purge.

The problems of domestic automotive production lies in a large weight, reciprocating and rotating parts, which, with its large mass, increase the wear of the other parts of the engine, and plus the power of the machine or falls or there are failures. The best way to fix similar problems is to simply facilitate the details, and this applies not only to valves, connecting rods, and replace the pistons. You can reduce the weight of the crankshaft by replacing the flywheel. The weight of the standard flywheel is 6.6 kilograms, and new parts are lowered up to 5.2. Replacing the old flywheel new, makes the engine dynamic, disappear of the failures at high power and speed, in addition, the engine will respond faster on the closure and opening of the throttle. The remaining parts of the engine, increase wear resistance.

Tuning carburetor nine

On other models of VAZ 21099, you can replace the carburetor improved, but in this series such work can not not require high costs, to replace additional parts and work itself. You can make small modifications in the system of jets, or play with the valve system, but it is only a slight degree to improve the operation of the car.

Tuning suspension

In any machine after the engine, the main system is the chassis. In domestic cars, it is made, good, but still, when driving, you can feel some shortcomings that can be easily fixed on your own. A frequent problem is a cutting ring, which needs to be replaced from time to time and is done with your own hands. Many at the same time turn to specialists, not knowing how to get a pomegranate in order to get a broken rifle ring and replace it. Of course, it can be difficult to get a grenade and in case of incorrect actions can be damaged, but it will be easier to disassemble it in the details and carefully dismantled, everything is in parts. After installing the pomegranate back to the native socket, with the slightest touch, this item may fall out. This is due to the fact that the new corkscrew ring is not installed, for fixation.

The second action that can improve the driving part of the VAZ 21099 is to replace the clutch and this work can also be made in conventional garage conditions. Of course, a problem may appear due to the lack of a lift, but the money is saved. First of all, you need to dismantle the adhesion and gearbox. The clutch consists of 4 parts, namely from the slave and pressure disk, the spring diaphragm and, of course, the clutch flywheel. When dismantling, there may be problems that are associated with the fact that the slave disk can fall out of the flywheel and fall at the same time it will be damaged, so you need to follow this. It is better to use the bullshit especially when removing the fastening of the casing and unscrew the bolts to block the flywheel. After dismantling, inspection, pressure disk and flywheel for chipping, damage or simple wear. Naturally, it needs to be done if only part of the clutch is replaced, and the entire system is fully installed. If still noticeable scratches and damage, it is better to change the spare parts. After that, it is worth considering the diaphragm spring and the supporting rings, for damage and also to replace the part. The clutch assembly is made in reverse order, but it must be remembered that the slave disk is installed in the flywheel, the pressure disk is the least discovered part of the hub. After that, you need to firmly twist all six bolts.

A frequent problem may be tapping the wheels when turning. The reason for this, already spoiled or defective silver, which must be replaced by the new one, and do it should be immediately after the occurrence of the symptom so as not to damage the remaining parts of the chassis. There are 3 types of shruses from a different material. The first material and the most common is rubber material, which is also used at the factory in the manufacture of the car. For rubber materials, they do not notice large negative aspects, but also a little positive, namely, a small life, and, of course, a large amount of marriage. Silicone Slus, is rarely used in production, or rather, only on a special order, but even in ordinary life, the details of such a material are not recommended to buy, due to the fact that silicone dries up, breaks down and does not fulfill the tasks. Polyurethane material has proven itself best, and now even after buying a new car, it is better to replace the analogue of such a model. It will give the movement of the car dynamics on turns and high speed. In addition, polyurethane, withstand external and chemical damage, which increases its life and wear resistance.

External tuning VAZ 21099

External tuning VAZ 21099 is distant from the ideal, but good modern time gave drivers many ways to fix it. So, for example, repainting the salon and the outside of the machine, it is great as after buying directly from the conveyor, and when purchasing a car from hand, when the paint has almost been fused. Painting can be made independently, but for this you will need a spray and garage with strong power outlets, as well as large in volume in order not to accumulate gases.

Good ventilation is recommended, but you can do well and open doors with good and not windy weather. You must first prepare the car, namely, remove the paint layer in order for the new layer of LOG smoothly. In addition, after with the help of sandpaper, the primary layer of paint is removed, the body must be checked for damage to the primer layer. If there are dents or cracks, then it is better to be primed, in order to prevent the spread of corrosion, which can damage in the future the newly applied layer of paint. After places and primer works are finished, applied to the paint layer, and in several stages. The paint is applied three times, and after each time you need to give a little time so that everything is dried. In the cabin, the car is painted in the same way, but all the furniture will have to be dismantled, and the slots and the instrument panel must be closed with a newspaper or better than a film.

After all the work, the car can not be used immediately, as the paint should finally dry. Works are made exclusively in spring or summertime, when the temperature is high and there is no large moisture concentration.

Further car body after repainting or already on the native layer, you can apply different kinds of film, which is now sold in large numbers on the car market. Naturally, the most often drivers use vinyl film due to their wide variety, light installation and low cost. The vinyl film is installed according to the window tinting technique. More precisely, the surface is first degreased, and then a vacuum is created with a hair dryer and a film is applied, which clings to the body. Its durability is not as big as other types, but due to its low cost it can often be replaced by a new one. In addition, with the help of vinyl film, you can perfectly hide places, scratches or chipping cars. There is also a chrome film that is often used to apply only for some details. It does not stick to the surface, and she simply pull such details like a hood, bumper or wings. Previously, naturally, the kit is worth shooting, although the installation is practiced and without disassembling body kit.

The appearance of the machine can be improved by using small parts of tuning, namely the installation of plastic disks, the installation of spoilers or similar parts that transform the machine. In addition, there are details that not only give the car a new look, but can help the driver yourself, or rather, make the car more functional. Such spare parts include a refrigerator installed on the roof of the machine.

Headlights VAZ 21099

Tuning Pharmacy VAZ is a great way to give the car a new and aesthetically beautiful appearance, and improve the quality of driving at night. Station headlights provide for the use of conventional parts with incandescent threads, which is why drivers have to search and replace light sources with halogen or xenon lamps. Xenon, as a rule, is an excellent option, but it has long been not used for a long time due to the ban on GOST, and simply because they blind over the cars. It is best to use the GT series lamps that are installed on racing machines. Such a light source is distinguished by the glow in 4000-5000k, while it focuses on the site of the road, which the driver should see, and does not spread throughout the area. Machines going towards meetings do not receive discomfort from such a glow. Ksenon lovers can not be upset, and rebuild the headlights for a new glow. We are talking about making angel eyes, or rather, the installation of 5 nests in a circle, and the use of smaller power xenon lamps. It creates a favorable and even glow on the road, and the car itself acquires a very attractive look.

Another improvement of the headlights is the installation of fog-components on the back of the car. Often in the garage can be lit up and, maybe, noncomplex, but one fog light is accurate, and it can be used to solve the problem. To install additional lighting, it will take only a small length of a wire and a relay with a chicken. Place for installation is better to take the left, since it is from this side the driver is located and so it will be better visible to the illuminated area for parking.

Bumper

VAZ 21099 Blood Replacement, this is a difficult matter, but at the same time can no problem make the appearance of the machine new and beautiful. There is a lot of way to update the body kit, or rather, the bumper, but it is best to have a complete replacement of parts. You can, for example, borrow bumper in old VAZ models. It will cost cheap for equipment, and the installation is easy to produce, right in the manufacturer's service centers. In order to choose the bumper of its color and form, it is worth contacting the service center. Of course, on the one hand, this is the perfect option, for those who want to change the appearance of the machine at the same time to do with low blood from money losses. The type of car can be a bit newer, but will not greatly differ from the previous due to the similarity of the shape and style stylistics, many models of the VAZ series. It is best to pay attention to the kites that make to order specifically for VAZ 21099 or on universal types.

So, for example, a lot of popularity is used for this model, a foreign manufacturer called Miller. Bumper is performed from fiberglass and here you can already find a lot of advantages. This also applies to lightweight weight, which affects the increase in power and fuel consumption. In addition, fiberglass, it is the material that will be resistant and for a long time to transfer all external factors of influence. Chemical and mechanical impacts are not written out on the guise of this part, and even the temperature differences, which is normal, for the Russian region can not affect the quality of fiberglass. Work on the manufacture of fiberglass bumpers, manually produced in three layers. The first layer is the main material, then there is a polyester resin, on which the plastic is already applied to fully hide fiberglass, and already when painting, the last layer is applied smaller. The data of the bumper are more expensive than domestic, but at the same time they will work perfectly to this model of the machine and they can even be made to order.

Tuning side mirrors

Full-time Side Mirrors VAZ 21099 are far from high-quality products. Drivers often complain that they cannot control them on modern way, right from the cabin, the side mirrors do not have a heating system, and even the mechanical setting has its own minuses that there is a limit. Of course, it affects the most on security, when driving. The problem is solved by the fact that the mirrors are replaced by new and make it simple enough. It is surprising that many mirrors already with built-in modern technologies in their structure refer to universal types, and therefore it will not take a large amount of time to find equipment for installation on the VAZ 21099 model.

Front panel and instrument shield

When the classic style of the interior machine begins to bother, so at the same time, there is also a long time ago and outdated, it needs to be updated or replaced. The first thing to pay attention to is on a torpedo of the car, which most often falls into the field of view of the driver. There are, of course, the easiest of time in terms of time, namely buying a new instrument panel and its subsequent installation, but as the practice says this business is expensive. You can upgrade the old system of instruments and with the help of your hands, and will not need for this large investment. Nowadays, there are weights of stickers, equipment for creating a new creation, and just work is easy. First of all, it is worth dismantling all the devices on the panel. Work will be carried out on the example of a tachometer.

To begin with, the roller rim of the tachometer is removed, followed by the removal of glass. Next, it is necessary to remove the arrow and there may be difficulties with standard equipment, where the arrow sits often quite firmly. If two minutes later, it's not necessary to dismantle the arrow, then it is not necessary to make efforts so as not to drive it or not to break it, but it is better to sprinkle with a small amount of WD-40. After that, the arrow will become a supple. After the work performed, all the instrument panels need to be left alone and search for stickers. Naturally, they can be bought in the bazaar, but can be made with their own hands. All that this will require this is a good printer for printing.

The craftsmen work in programs for editing pictures, can improve the pre-dried photo. The printed sticker is installed with the help of glue, while it is better to use the water-resistant adhesive substance due to the frequent moisture from entering the device panel. After the whole procedure, the work can be finished or continuing and installing a new backlight, replacing standard LED lamps. There is one secret that allows you to make LED lights are not directed and scattered, which is aimed much better in the instrument panel, and at the same time does not distract the driver while driving. For this head of LED lamps are cut off, and transparent glue is applied to their place. After checking all the equipment, the instrument panel is installed back into place.

Luggage compartment

Tuning of the luggage compartment This work is not easy at least for the reason that the driver often simply do not know what to modify in it. Of course, that there is a lot of way to make the luggage compartment better, but this is usually fantasy and the work of the drivers of amateurs. So, for example, for those who do not carry potato bags in the trunk and simply not use it, it is suitable for the installation of an acoustic system. Work is made easily and often on their own. First you need to make a housing from plywood to install columns. Plywood sheets preliminarily cover some fabric for aesthetic beauty. Next, the holes are cut into the plywood to install new columns. You can connect them first to the central buffer, and only then to the power source. By the way, even the headlights are suitable for such work, which is given the necessary voltage.

Tuning salon VAZ 21099

You can make a VAZ 21099 the fastest and most powerful changing all parts in the engine, and installing new equipment from above, but people always looking at the appearance of the machine and the state of the cabin. I would like to note that the tuning of the salon is a case quite costly, but after the end of the tuning, often the drivers do not arise about the work done. There is a whole mass of how to update the car from the inside. Begin, perhaps, you need from plastic bases, and this applies not only to the front panel of instruments, gloves, but also plastic panels installed on the doors. You can buy new panels, manufacturer especially for this car model, but it is best to simply cover the plastic panels chrome-plated or vinyl film. The panel will need to be pre-dismantled, which is not easy enough. If she has been plastic with leather material, then first will need to cut molds, but it is difficult to do it enough to make the material to Rivne, and neither going to the waves. Therefore, it is better to use a chrome-plated film that is easy to apply. The front plastic is very difficult to dismantle, so it is better to paint it. You can paint panels completely, but you can create a contrast. To do this, close places that are not recommended to paint with a newspaper or better than a film. It by itself that work is not for beginners, but still it can transform the car.

The interior of the car is updated gradually and can not be forgotten about small details, for example, about the trim. The steering wheel, very quickly because of the constant friction with his hands, erases and loses his beautiful past. There may be three methods how to fix a similar problem. First of all, you can simply remove the old trim, and to strip the steering wheel with a new material. It is advisable to choose the skin that can withstand not only permanent contact with your hands and a high temperature especially in summer when the rays of the sun make their way through the windshield. You can just buy covers ready for the steering wheel, which are tightened with laces and is practically nothing can be seen from the old material, but the central part does not remain closed and can be created unpleasant contrast for the eye. There is a third method and the most expensive at the same time, namely the full replacement of the old steering wheel. The problem is that new steering steers are cheap, but their installation is made only in services, which means you will have to upset.

Of course, the inner coating remains, such as the floor ceiling, armrests. Working with these parts is performed in the same style as with panels. That is, you can, dismantle all the details and repaint them or cover them with a cloth, and you can choose the most ordinary fabric, because the roof of the machine is not strongly exposed to mechanical effects. During the repair of the roof, you can install the heating system. It is useful to do if children often ride in the car, and in winter it's no secret that in the car is cold enough.

The last touch touche tuning the car's salon is furniture, which, as well as the steering wheel, constantly comes into contact with something, which means it is erased, rushes and burns out of the sun. Replace furniture trim, not easy, but there is nothing no possible. To begin with, all the trim from the old furniture is made to shoot, dismantling the springs and foam rubber. It is recommended to work only in the respirator, as Porolan for a long time turned, most likely in dust. Springs can be replaced partially or completely depending on their state. It is better to buy a complete set of springs to be confident that after repair, they will not shoot. Material You can choose the most different and variety problems in the market. It is necessary to choose not only the color gamut, but the material itself. There are conventional fabrics that are often suitable at their price, but what about quality, they are inferior. Conventional universal fabrics quickly burn out in the sun and rush. It is better to give preference or skin or special material for the upholstery. Of course, that by the price they cost much more expensive, but you can be sure that for a long time, you will not need to repair the car in the cabin.

An alternative option for changing the styles of the cabin, and in particular it concerns furniture, in the use of covers. Naturally, their use is far to indicators and beauty that appears after the repair of the furniture machine, but this method can save and time, and a large amount of money. So, for example, the purchase of model covers can be compared at a price with the usual work of the furniture repair, but at the same time save a lot of time. The high price is due to the fact that the furniture covers do only manually, pre-making measurements of all seats. Negative qualities, except prices, these covers do not have. They are perfectly suitable for seats do not roll and are not going to waves, they can stand all chemical and mechanical impacts, which is especially good, because covers often need to be washed. The material is used quality, beautiful and comfortable both for passengers and for the driver itself.

For those who do not really want to spend money on tuning salon VAZ 21099, but still the old and the worn design is already starting to cut the eye, it is suitable for the purchase of universal covers for the car. The advantages of universal covers are a bit, as they are made of ordinary and poor-quality fabric, but due to low prices, people can afford to replace the material every year.

Tuning dashboard car VAZ 2108, 2109, 21099. How to make the backlight of the scale with your own hands?

On the instrument panels of cars VAZ 2109 and VAZ 2108, lamps are installed, which highlight the dial outside, i.e. from the side of the arrows. Such a backlight does not always satisfy drivers because the brightness is low and the detail is fuzzy.

This article will consider how you can make the dashboard backlight from the inside on the example of tuning VAZ 2109 with your own hands. Of course, you can seek tuning to a specialized company, there will quickly make a backlit panel as on foreign cars, but the cost of such work will be high. In order to save well on your car and make the desired backlight, the instrument panel needs to be modified independently, the more, there is nothing very difficult in this.

We make the LED panel do it yourself on the VAZ 2109

For tuning backlighting your car, you will need a lightweight pad, suitable for the instrument panel.

From the car removed and disassemble the instrument panel. We remove all the arrows and an old lining, it will no longer need it. With the help of a heated knife or soldering iron on the acquired pad, you need to make cutouts so that the light from the backlight falls on the instrument panel from the inside.

The backlight itself will be framed from the LED tape. The tape must be cut into pieces of three diode. For the uniform distribution of light over the entire surface, the usual foil is needed, which is distributed throughout the entire panel under the appliances.

The speedometer and the tachometer will need 3 pieces of ribbon, and on the temperature pointers of the coolant and fuel level - on one tape.

This material is also suites to the topic where other decisions on the upgrade of your car are described.

stock Foto Dashboard tiling report

Old backlight should not be removed, as it will highlight the arrows of the appliances. It can be slightly upgraded to it, for this, glue the LED tape to the place of regular lamps. The tape is better to toned in advance, with the help of a toned film or a black marker, otherwise the light will be too bright, which interferes when driving. It is advisable to leave a regular light filter, so the light will be more uniform, soft and with a bluish tint.

The entire installed backlight must be connected to the contacts on the plate of the standard backlight lamp, according to their polarity. There is a special driver, it stabilizes the current when sticking the installed LEDs.

Now you need to check the operation of the resulting backlight, for this you need to apply voltage to 12 V DC.

Standard dashboard VAZ 21099

Tuning salon VAZ 21099 provides for the dismantling and installation of the European. It should be noted that the high VAZ panel is removed longer than the low design of this type. In any case, the following tools are needed for such tuning:

• screwdriver Set;
• nuts and washers;
• current indicator;
• wires.

Step-by-step tuning actions

Before dismantling the VAZ 21099 panel, it will be necessary to remove the terminal with the power supply. Then the decorative steering wheel cover is removed. The nut should be unscrewed so that its end is flush with a similar element of the steering column shaft. It is impossible to turn it away. Then the tuning of the VAZ 21099 panel provides for removing the steering wheel.

After the weaplation of 6 screws of the fixation of the lower casing, it will be necessary to remove it. Facing the ignition switch is dismantled. The next step provides for a bolt tightening, which fixes the base of the switches. The last element is removed from the shaft, and 2 blocks with appropriate wires are disconnected.

It will take to marke the switches of the washer and wiper. A block with wires from the corresponding levers and turning pointers are disconnected. SUPPLC should be pulled so that the thrust arose. At the same time the pen of the first unit stretches. Then the cantole lining bolts are turned on the panel and the lining itself is removed.

From the nest, the cartridge of the cigarette lighter and ashtray is pulled out. Torpeda VAZ is equipped with a heater fan that will be needed to remove. This is recommended to use a screwdriver. From the fan switch, the shoe and two wires are disconnected. They highlight Europantel.

Tuning instrument panel

You still need to disconnect the headlights of the headlights and the lighting switch. After the evaporation of the nuts, the corresponding switch is pushing inside the panel. Side nozzles are removed by a screwdriver. The high panel provides for the lips of the lining fixation bolts. Latest elements from two sides of the torpedo.

Subsequent tuning is carried out with regard to the removal of the nest for the radio. Existing audio equipment is pre-dismantled. Then the latches are removed using the screwdriver and the lining is raised. The shoe and wires are disconnected from the cigarette lighter. A similar step is carried out with respect to the illumination and the signaling switch.

Final stage of work

The high VAZ panel is dismantled carefully, since the ones are latches that quickly break. After disconnecting the pad from other element, the entire combination of devices is dismantled. The final step is based on disconnecting the cable from the speedometer. If the Europantel is equipped with additional equipment, then you need to be even more neat. Tuning Torpeda provides for disconnecting the pad from the following aggregates:

• onboard control system;
• ignition relay;
• remaining panel instruments;
• lamps backlighting.

It will be necessary to unscrew the screws of the main fixation of the torpedoes on both sides. With a screwdriver, the plug is pulled out and the side fixing screws are turned away. Europancelle is removed at the final stage. Installing a new design of this type is carried out in reverse order. Upon completion of this procedure, the operation of the switches is checked.

Often tuning Torpeda VAZ provides for dismantling plastic and removing the panel board. In this case, the following tools and materials will be required:

• soldering iron;
• europinel or insert;
• ultraviolet light bulb;
• wires;
• light bulbs;
• cartridges;
• glue;
• marker.

Initially, it will be necessary to remove the old Europaninel, remove the glass and the existing edging. Gently pull out the insert and arrows. Special attention should be paid to the new insert. Holes are recommended to do with some reserve. This will prevent the arrows sticking.

Next, tuning is based on the dismantling of the standard backlight. In this case, plastic can break. Originally dismantled fee. Experts advise pre-apply an existing connection and compound scheme on paper.

The standard backlight is replaced by neon lamps. Neon is glued to the panel. Plastic protection is fixed on top. At the same time, it is necessary to check whether this design is secure. The block, with which the neon lighting is controlled, should be glued to the Europeanlyl. To do this, you can use glue or bilateral scotch.

Such tuning is easily performed with your own hands. An important point is to install the panel and the proper connection of its instruments to the network. For this, auto mechanics recommend using books on the repair and operation of the VAZ 21099.

Many car owners believe that tuning must first allocate and emphasize its presence. Therefore, all that will be found on the car in the local car market. But you can do something and useful and comfortable. And first of all for yourself. To make it nicer to drown time in the car, stand with cold and snowy winter evenings in traffic jams. Increation will surely immediately think about changing a terrible low or rattling high torpedo on a foreign one or something from this opera. But after all, on a torpedo and instrumental pvnel, we just look, and contact directly with the wheel. Of course, you can go to the local car market and buy yourself instead of a frankly wretched standard steering wheel (both old in the spirit of a century and more new with a big signal) New Turkish or Chinese. And with screaming inserts with red or blue. But you will not be surprised that the skin is zero there and that after some time it will cut down, gets off, etc. ...

We offer to your reflection such refinement as a hauling of the helm of the skin, and at the same time the installation of the steering wheel. The latter is very relevant for residents of the northern regions, and such decent. Although you can restrict ourselves and simply crawling the helm of the skin. And if you have cold winters or very cold winters, then WPare with autorun This refinement is generally a fairy tale. He came out of a warm house, sat down in a warm car, took up the warm steering wheel ... I think it's not necessary to convince anyone that even if the salon is warm up 15-20 minutes, then the rim of the steering wheel does not warm ............ .....

Earlier, we have already published an article here. Now, we publish a similar material for the owners of "Chisel" with a high torpedo.

If we consider the sad glory of this torpedo as the most rummy, it is quite easy to understand why the owners of these cars are ready to spend a lot of time to silence it. The removal of high torpedoes has almost 2 times more steps than the removal of low .............

VAZ is such a car that every owner trying to make it at least a little better, sooner or later comes to the conclusion that you need to remove the torpedo. In order to sneak it from a screen or sample the wall of the engine compartment with vibroplast. Either to decide on its replacement at all ... there are enough options!

Disconnect the wire from the terminal "-" battery. Install the wheels in the position of the straight movement. Disconnect the carburetor air damper lever and the speedometer drive cable from the gearbox ...................