The Japanese Corporation TCM supplies loaders to the Russian market since 2005. For such a short period of time, its products found a huge number of consumers who appreciated the quality, reliability, performance and durability of technology. Electric loaders are used in great demand, in particular TCM FB15-7. FB series electric loaders are distinguished by compact dimensions that allow you to freely maneuver in a limited space and use storage space to most effectively. It is worth paying particular attention to the fact that the innovative energy saving system allows TSM FB15-7 to increase the continuous operation of the equipment on a standard battery with a capacity of 48 volts to 8.5 hours. Thus, a longer period of operation of the electric goods loader TCM FB15-7 is provided without additional recharge. Also, the modern model of an asynchronous engine with an average load of 55% provides the operation of the FB15-7 TCM loader without recharging the batteries for half an hour more than the motor used earlier on the previous generation four-voltage machines. The principle of operation of the FB15-7 model is based on alternating current technology. Also, the modern model of an asynchronous engine with an average load of 55% provides a loader operation without recharging batteries for half an hour more than the motor used earlier on the previous generation four-voltage machines. The principle of operation of this type of technology is based on alternating current technology. Also, the operator can choose the necessary mode of operation of the electric loader TCM FB15-7, taking into account the specifics and volume of tasks - economical, reinforced and maximum performance. It is necessary to take into account that the standard lift height is 3 meters. If you decide to buy TCM FB15-7You should consider all the above technical parameters.
FB series electric loaders, in particular the FB15-7 model, have a number of important features, thanks to which the technique is competitive in its market sector. Most significant include self-diagnostics, allowing the operator to control the process of performing work. Conclusion of error codes, statistical data is performed on the monitor. Also, the operator has the ability to program the parameters in advance on the FB15-7 model. It is worth noting that in the electric loader TCM FB15-7 There is a smaller separation of heat and wear of parts of the equipment, energy recovery when braking, high acceleration and smooth braking reverse. Advanced operational capabilities and increased service life makes TSM FB15-7 by irreplaceable technique in the loading and unloading work of any complexity even in the most cramped warehousing conditions.
Electric loader TSM FB15-7 occupies a leading position in its market sector in Russia. A long period of using warehouse equipment without recharging noticeably highlights it from among other production. Excellent value for money makes electric goods loader with a lifting capacity of 1.5 tons in demand. Sale TCM FB15-7 It is carried out in our company, taking into account the requirements of the consumer and with delivery to any region of Russia. If you decide to buy TCM FB15-7, contact us by phone shown on the site in the "Contacts" section, or by email. Managers will provide you with the necessary information regarding the selected model of technology of this purpose, will advise you regarding the technical characteristics and operational capabilities of electric loaders. Buy TCM FB15-7 - It means to be confident as purchased products.
Electric loader TCM FB15-7 - This is the representative of the FB series with an increased lifting height. The electric loader combines high performance and efficiency. Electric loader is designed to perform loading and unloading. The total weight of the cargo should not exceed 1.5t. High maneuverability, small dimensions - all this allows the use of this model in cramped conditions. Small dimensions of the FB15-7 loader are in a height of 1995/0050 millimeters (where the first figure is a long mast, and the second driver's fence), and in a width of 1070 millimeters, with a minimum external reversal radius, is 1700 millimeters. All this allows the electric loader to more rationally use the warehouse area, by minimizing the distance between the racks.
TCM FB15-7 It is characterized by such advantages as electricity savings. It has the greatest time of continuous operation among the machines of its class. It carried out improvements aimed at reducing power consumption. Loader designers managed to increase the duration of 30%. It also has a fully automated charger. A microcomputer responds in the FB15-7 charger. Charged batteries have a particularly accurate adjustment of the battery charge process. This system applied in these loaders is the first such system implemented in this industry.
In the basic configuration of the loader has an automatic transmission. This simplifies its management. The operator of the loader only needs to choose the direction of movement (forward or backward). Also, the electric loader is equipped with an electric motor without brushes. This design increases the interval between that and has a smaller operating value. Also, at the expense of inductive braking by the engine, the design it highlights less heat and reduces wear of parts. To ensure uninterrupted, the reliable operation of the FB15-7 loader is equipped with a sample self-diagnosis. The self-diagnosis of the loader includes the output of error code, error statistics, and also features the parameter programming feature. For more competent energy consumption, there are three modes of operation. Thus, depending on the volume and intensity of work on TCM FB15-7 You can choose economical, reinforced mode and maximum performance mode.
For more competent use of energy resources, TCM FB15-7 has recovery when braking. Recuperation is the return of a part of the energy spent when conducting braking for reuse. Loader design provides smooth braking with a reverse and high acceleration rate. The principle of operation is based on alternating current technology. The new model of an asynchronous engine existing in TCM FB15-7, with an average load of 55% ensures the operation of TCM FB15-7 without recharging the batteries for half an hour more (compared to the motor, which was used on the previous generation four-voltage machines).
To ensure the most convenient operation, the TCM operator FB15-7, changes were made in the design aimed to reduce vibration by 65% \u200b\u200b(the operator's seat has a shock absorber), and the noise from the engine operation (by 20%) was reduced. This allows the operator of the loader, fully focused on fulfilling its duties without being distracted by external irritating factors. To work on the loader, there is no need to have special training. Due to the competently performed management system, anyone may in the shortest time to learn. Adjustable steering column TSM FB15-7, allows you to conveniently arrange the steering wheel in height, and a convenient adjustable chair of the operator TSM FB15-7, is able to configure under individual growth and weight.
Due to the high reliability of TSM FB15-7, ease of operation and maintenance, the TCM loader FB15-7 quickly gained wide fame not only in his homeland, but also in Europe. FB15-7 forklifts are traditionally high performance, excellent quality, exceptional reliability and are easy to operate. Thanks to the unique technology and extensive experience of TSM, the FB15-7 forklift is optimal productivity in its class, while ensuring unsurpassed convenience and safety.
TCM FB15-7 In addition to the standard package, it can be supplied with two and three-speed lift racks (VFM and VFHM). To expand the scope of use of TCM FB15-7 on request, the client is equipped with additional attachments - a wide carriage, swivel forks. Also, the design of TCM FB15-7 can be complemented by double front wheels and an extended wing, massive or colored tires. By order, TCM FB15-7 can be equipped with adaptations to work in the paper industry, to work in the construction industry, as well as for loading and unloading operations of cardboard boxes and glass. Here is the entire list of mounted equipment on TCM FB15-7: forks of various lengths, grip for bales, capture for cardboard, crane console, gripping for barrel, fork grip, plug extension supplies, plug fixture (hydraulic type), fork installation device (manual type ), high and wide supporting wall of the cargo, plug on hinges, bucket, cargo sample, shipping, taran, rotary grip for bales, swivel plug (attachment, built-in type), side displacement device, hook with sleeve.
Characteristics | |||
Model | |||
Load capacity | |||
Center of gravity loads | |||
engine's type |
Electric |
||
Position operator |
|||
Type Tire |
Before / back |
Pneumatic |
|
Number of wheels (x \u003d leading) |
Before / back |
2x / 2. |
|
Performance features | |||
Speed | Movement * (back and forth) |
||
Without cargo |
|||
Lifting * | |||
Without cargo |
|||
Lowering | |||
Without cargo |
|||
Traction effort ** |
Instant |
7.5 kN |
|
Permanent |
3.0 kn. |
||
Overcome assessed ** | |||
Without cargo |
|||
Weight | |||
General weight | |||
Distribution |
With cargo |
Before |
3645 kg |
Back |
565 kg |
||
Without cargo |
Before |
1120 kg |
|
Back |
1590 kg |
||
Chassis | |||
Wheels | number |
Front / rear |
|
The size |
Front |
6.0 0-9 -10Pr. |
|
16x6 -8-10 pr. |
|||
Wheelbase |
|||
Track |
Front |
||
Ground clearance |
Minimum |
||
Brake |
Hydraulic, pedal |
||
Parking |
Mechanical, manual |
||
Electric motors and control system | |||
Rechargeable |
Voltage / Capacity |
48/400 V / A-h |
|
Weight (with rechargeable box) |
695 kg |
||
Electric motor |
Traction engine |
11.5 kW / 3min |
|
Engine hydraulics |
8.6 kW / 5min |
||
Engine GUR. |
0.35 kW / 60min |
||
Control system |
Traction engine |
MOS-FET inverter |
|
Engine hydraulics |
MOS-FET converter |
||
Engine GUR. |
IGBT converter |
||
Operating pressure |
For hinged equipment |
14/2 (145) MPa (kg / cm2) |
Note:
* The numbers are indicated for the "Super" mode
** Computer calculation data
*** Rechargeable batteries are optional equipment.
Standard dimensions | |||
1 Height of the raised mast (with a protective grid) | 4030 mm | ||
2 Lifting height Vil | 3000 mm | ||
3 Height of folded mast | 1995 mm | ||
4 Height of the protective lattice | 1000 mm | ||
5 Free Care | 155 mm | ||
6 Thickness Vil | 35 mm | ||
7 Minimum clearance | 95 mm | ||
8 Total Length (with forks) | 2875 mm | ||
9 Total Length (without Wil) | 1950 mm | ||
10 Length Vil | 920 mm | ||
11 Distance from the front axle to the back of the Vil | 375 mm | ||
12 Wheel Base | 1250 mm | ||
13 Distance from the rear axle to the edge of the counterweight | 330 mm | ||
14 Height to towing finger | 390 mm | ||
15 Machine height without protective lattice and mast | 1350 mm | ||
16 Distance to protective roof (from the surface of the seat) | 990 mm | ||
17 Total height (with a protective roof) | 2050 mm | ||
18 Total width | 1070 mm | ||
19 Installation forks horizontally (on the outside) | 200 ~ 920 mm | ||
20 Pitch (Front) | 910 mm | ||
21 Pitch (rear) | 900 mm | ||
22 Width Villa | 100 mm | ||
- | |||
24 external reversal radius | 1700 mm | ||
25 Minimal passage | 1690 mm | ||
26 Angles of the tilt of the mast (forward / backward) | 6 ° -12 ° |
Dimensions with double front wheels (option) | |||
Tire size (front double) | |||
General weight | +40 kg | ||
18 Total width | 1270 mm | ||
20 Pitch (Front) | 1055 mm | ||
23 Internal Radius | - | ||
24 external reversal radius | 1745 mm | ||
25 Minimal passage | 1780 mm |
Road clearance (clearance) | |||
By mast | 105 mm | ||
In the center of Rama | 95 mm | ||
According to the leading bridge | 95 mm | ||
According to the controlled bridge | 115 mm | ||
By opposition | 125 mm |
Standard Equipment and Accessories Equipment
Controls Accessories Switches Digital liquid crystal display * In addition to models V Optional attachments Capture for kip Optional Equipment and Accessories Equipment Accessories |
TCM electric loaders have compact dimensions, which allows working space to use with maximum efficiency and safety.
The basis of the operation of electric loaders TSM is the principle of AC. The new brand of an asynchronous motor provides the operation of the device without recharging batteries for 30 minutes. longer compared to the engines of the previous generation. Given the intensity and volume of work, you can choose the optimal mode. There are three of all three: economical, maximum, reinforced performance.
Features of the model:
1. Self-diagnosis.
2. Remove error codes, error statistics.
3. Programming parameters.
4. Energy recovery when braking.
5. Low heat release and wear loader.
6. Motor without brushes provides an increase in the intervals between that.
Equipment:
- tank for brake fluid;
- towing device;
- ergonomic seat;
- carriage II and III class ITA;
- steering column adjustable in height;
- carriage fence;
- widespread mast;
- forks 920 and 1070 mm;
- reverse hydraulic filter;
- smooth stroke lift cylinder;
- driver protective fence;
- bescas missing brake pads;
- mastlock lock valve;
- bugged wheels;
- 2-section distributor;
- inlet hydraulics filter;
- support hood amortic type;
- system anti-paramele;
- electric power steering system;
- load check valve;
- interrupting valve of the cargo system;
- regenerative brake system;
- oil level indicator.
Controls:
- cross indicator lever with self-return mechanism;
- lift control levers, mast slope;
- control mode selection lever;
- parking brake system;
- speed \u200b\u200bControl Switch;
- electronic motion direction switch.
Specifications:
Accessories:
- holders for tools and documents;
- headlights;
- sound signal;
- rear view mirrors;
- rubber rug;
- protection of tilt cylinders;
- front and rear combined lights;
- operator seat control levers;
- reversing buzzer;
- a set of tools for the operator.
The electric loader TCM is characterized by compact sizes and allows you to freely maneuver in a limited space and most effectively use storage space. A modern energy saving system allows you to increase the time of continuous operation with a standard battery to 8.5 hours, when equipped with a rechargeable battery of high capacity for a longer period of uninterrupted operation.
The traction AC motor during braking allows you to reuse electrical energy due to the recovery, which extends the battery life without additional recharging. Compact AC motor is very reliable and practically does not need maintenance. Depending on the work performed, you can customize the high-speed modes of the loader operation, which allows you to maximize the efficiency of the battery. With the use of the new AC electric motor, the engine braking is possible, which made it possible to reduce the braking path and exclude the rear wheel drive.
The price of the TCM is not much higher than on diesel or gasoline loaders, but in the first year, the technique will prove efficiency in operation and rewinding, which will allow to stop the choice on this type of loaders and buy electrical loaders for warehouse work. With the use of the new AC electric motor, the engine braking is possible, which made it possible to reduce the braking path and exclude the rear wheel drive.
With the use of the new AC electric motor, the engine braking is possible, which made it possible to reduce the braking path and exclude the rear wheel drive.
The time of continuous operation without recharging increased to 8.5 hours.
General characteristics
Characteristics | |||
Model | |||
Load capacity | |||
Center of gravity loads | |||
engine's type |
Electric |
||
Position operator |
|||
Before / back |
Pneumatic |
||
Number of wheels (x \u003d leading) |
Before / back |
||
Performance features | |||
Speed | Movement * (back and forth) |
||
Without cargo |
|||
Lifting * | |||
Without cargo |
|||
Lowering | |||
Without cargo |
|||
Traction effort ** |
Instant |
||
Permanent |
|||
Overcome assessed ** | |||
Without cargo |
|||
Weight | |||
General weight | |||
Distribution |
With cargo | ||
Without cargo | |||
Chassis | |||
Wheels | number |
Front / rear |
|
The size |
Front |
||
Wheelbase |
|||
Track |
Front |
||
Ground clearance |
Minimum |
||
Brake |
Hydraulic, pedal |
||
Parking |
Mechanical, manual |
||
Electric motors and control system | |||
Rechargeable |
Voltage / Capacity |
||
Weight (with rechargeable box) |
|||
Electric motor |
Traction engine |
11.5 kW / 3min |
|
Engine hydraulics |
8.6 kW / 5min |
||
Engine GUR. |
0.35 kW / 60min |
||
Control system |
Traction engine |
MOS-FET inverter |
|
Engine hydraulics |
MOS-FET converter |
||
Engine GUR. |
IGBT converter |
||
Operating pressure |
For hinged equipment |
14/2 (145) MPa (kg / cm2) |
Note:
* The numbers are indicated for the "Super" mode
** Computer calculation data
*** Rechargeable batteries are optional equipment.
Full description
Standard Equipment and Accessories
Equipment
. Anti-paramele system
. Bescas missing brake pads
. Brake fluid tank
. SUPPORT OF THE HOUSE OF AMORTER TYPE
. Ergonomic seat *
. Towing device
. Electric power steering system
. ITA class II and III carriage
. Oil Level Indicator 8 Hydraulick System
. Interrupt loading valve
. Fencing carriage
. Load check valve
. Driver protective fence
. Regenerative brake system
. Reverse filter hydraulics
. Barded wheels
. Smooth stroke lift cylinder
. Inlet filter hydraulics
. Height adjustable steering column
. Mastlock Lock Valve
. Widely overview mast
. 2 Section Distributor
. Clauses 920 mm (1,1.5, 1.8 t.), 1070 mm (2, 2.5.3T)
Controls
. Electronic Motion Direction Switch
. Lifting levers and tilt mast
. Parking brake system with internal locking
. Control mode selection lever ("Super" reinforced / economical)
. Speed \u200b\u200bControl Switch
. Rotation pointer lever with self-return mechanism
Accessories
. Rear stroke buzzer
. Holder for documents
. Sound signal
. Front combined lights
. Headlights
. Highly located rear combined lights
. Rubber mat
. Set of operator tools
. Rear view mirrors
. Protection of cylinders of inclination
Switches
. Combined light switch and rotary signals
. Egnition lock
Digital liquid crystal display
. Battery Charging / Discharge Layout Indicator
. Battery Discharge Warning Indicator
. Controller overheating indicator
. Experience Indicator Traction Engine
. Counter Motocamis
. Indicator of neutral position
. Parking brake indicator
. The mode selection indicator ("Super" / Stressed / Economical)
. Display with self-diagnostic function
. Speed \u200b\u200bControl Indicator
. Speedometer
* In addition to models V
Optional attachments
. Capture for kip
. Villa extension cords
. Positioner
. Increased in height or width carriage fence
. Facility
. Stabilizer cargo
. Long forks
. Rotating forks
. Rotating grip for roll rolls
. Care shift device
. Hook
. Swivels
. Width carriage
. Two-stage widespread mast with free progress VFM carriage
. Three-speed Werewide Mast with Vfhm Care
Optional Equipment and Accessories
Equipment
. Additional hydraulic sections
. Accumulator battery
. Charger (built-in, stationary) Except FB18 ~ 7
. EXCEPT FB18 Electrolyte Central Pouring System ~ 7
. Central lubrication system
. Low-temperature specification and specification for the fishing industry (-35 ° C, -45 ° C)
. Colored solid tires (white: green)
. Double front wheels
. Fully hydrostatic control cylinder
. Open cabin
. Increased driver fence (+60 mm)
. Allolished tires
. Windshield with wiper
. Configuration with 2 brake pedals
Accessories
. Battery case with brackets for lifting
. Rear Top Witter With Changeable Volume
. Central rearview mirror
. Front
. Coloring in the color of the customer
. Fire extinguisher
. Farm protection
. Mast Angle Index
. Brozent cabin
. Rear lights
. Flashlight (Red, Yellow)
. Flashlight, synchronized with reverse signal
. Anticorrosive painting
. Steel Mesh Driver Fence
. Protective Case Cover Cylinder
. Protective covers of tilt cylinders
dimensions
Standard dimensions | |||
1 Height of the raised mast (with a protective grid) | 4030 mm | ||
2 Lifting height Vil | 3000 mm | ||
3 Height of folded mast | 1995 mm | ||
4 Height of the protective lattice | 1000 mm | ||
5 Free Care | 155 mm | ||
6 Thickness Vil | 35 mm | ||
7 Minimum clearance | 95 mm | ||
8 Total Length (with forks) | 2875 mm | ||
9 Total Length (without Wil) | 1950 mm | ||
10 Length Vil | 920 mm | ||
11 Distance from the front axle to the back of the Vil | 375 mm | ||
12 Wheel Base | 1250 mm | ||
13 Distance from the rear axle to the edge of the counterweight | 330 mm | ||
14 Height to towing finger | 390 mm | ||
15 Machine height without protective lattice and mast | 1350 mm | ||
16 Distance to protective roof (from the surface of the seat) | 990 mm | ||
17 Total height (with a protective roof) | 2050 mm | ||
18 Total width | 1070 mm | ||
19 Installation forks horizontally (on the outside) | 200 ~ 920 mm | ||
20 Pitch (Front) | 910 mm | ||
21 Pitch (rear) | 900 mm | ||
22 Width Villa | 100 mm | ||
- | |||
24 external reversal radius | 1700 mm | ||
25 Minimal passage | 1690 mm | ||
26 Angles of the tilt of the mast (forward / backward) | 6 ° -12 ° | ||
Dimensions with double front wheels (option) | |||
Tire size (front double) | |||
General weight | +40 kg | ||
18 Total width | 1270 mm | ||
20 Pitch (Front) | 1055 mm | ||
23 Internal Radius | - | ||
24 external reversal radius | 1745 mm | ||
25 Minimal passage | 1780 mm | ||
Road clearance (clearance) | |||
By mast | 105 mm | ||
In the center of Rama | 95 mm | ||
According to the leading bridge | 95 mm | ||
According to the controlled bridge | 115 mm | ||
By opposition | 125 mm |
Photo
The electrical loader is indispensable under good power supply. We offer a profitable partnership and affordable prices for all types of technology. Our company is engaged in selling electric loaders in Novosibirsk. The warehouse contains more than 1000 units of products. You can buy a turnkey forklift, that is, get its full service, warranty and post-warranty repair. Moreover, our masters can work on the road.
Assortment of catalog
We supply new electric loads for a warehouse, terminals, airports, large stores, construction sites, etc. We sell products from Japanese and Chinese manufacturers. We offer reasonable cost of special equipment and components.
In our catalog you will find cars with such characteristics:
- Load capacity - from 1 to 3 tons. The most versatile models are 2 tons. Suitable for work at enterprises and warehouses. Compact, easily cope with tasks both outside and indoors.
- The number of supports. On this basis, you will find 3- and 4-Hour structures. The first differed of greater maneuverability, others - stability.
- Power. We have models from 10.4 kW.
In addition to good prices for electrical loaders, we offer the most favorable terms of implementation. With us you can arrange cars in leasing, credit. For samples of technology, you can order the rental of some devices.
In addition, we have a complete technical service. We sell spare parts for electric and other loaders, repair them and serve. Our masters received appropriate qualifications, practical training on factories. Therefore, they carry out high-quality and reliable service of machinery of all types. If necessary, go to place and eliminate faults.
Buying an electrical loader with us - this is saving funds and 100% guarantee of further maintenance.
Electric forklift |
TSM.FB.15 - 8 VM300. |
Basic loading |
1500 kg |
Center of gravity |
|
View of mast |
two-stage |
Standard dimensions | |
1 Height of the raised mast (with a protective grid) | 4030 mm |
2 Lifting height Vil | 3000 mm |
3 Height of folded mast | 1995 mm |
4 Height of the protective lattice | 1000 mm |
5 Free Care | 155 mm |
6 Thickness Vil | 35 mm |
7 Minimum clearance | 95 mm |
8 Total Length (with forks) | 2875 mm |
9 Total Length (without Wil) | 1950 mm |
10 Length Vil | 920 mm |
11 Distance from the front axle to the back of the Vil | 375 mm |
12 Wheel Base | 1250 mm |
13 Distance from the rear axle to the edge of the counterweight | 330 mm |
14 Height to towing finger | 390 mm |
15 Machine height without protective lattice and mast | 1350 mm |
16 Distance to protective roof (from the surface of the seat) | 990 mm |
17 Total height (with a protective roof) | 2050 mm |
18 Total width | 1070 mm |
19 Installation forks horizontally (on the outside) | 200 ~ 920 mm |
20 Pitch (Front) | 910 mm |
21 Pitch (rear) | 900 mm |
22 Width Villa | 100 mm |
- | |
24 external reversal radius | 1700 mm |
25 Minimal passage | 1690 mm |
26 Angles of the tilt of the mast (forward / backward) | 6 ° -12 ° |
Dimensions with double front wheels (option) | |
Tire size (front double) | 4.50-12-8Pr. |
General weight | +40 kg |
18 Total width | 1270 mm |
20 Pitch (Front) | 1055 mm |
23 Internal Radius | - |
24 external reversal radius | 1745 mm |
25 Minimal passage | 1780 mm |
Road clearance (clearance) | |
By mast | 105 mm |
In the center of Rama | 95 mm |
According to the leading bridge | 95 mm |
According to the controlled bridge | 115 mm |
By opposition | 125 mm |
Price with VAT: 1 650 000 rubles
Delivery time: In stock, shipment 3-5 business days.
Delivery conditions: Shipment from a warehouse of Moscow
Payment condition: 50% advance payment; 50% before shipment from the warehouse in Moscow.
Guarantee: Extended warranty 5 years.
The company GK Atlet is the official dealer of TCM technology in St. Petersburg and provides a full range of services for the maintenance of equipment by all the necessary consumables, spare parts, tires, attachments, and maintenance and repair in its service center, or in the customer's territory.