The function of the fuse box is to protect against overvoltage and electrical failure of the machine. Therefore, when, for example, headlights, a stove, or a gas pump stop working in your car, check the fuses first. Maybe the cause of the problem lies precisely in them.
Before you buy fuses or any Hyundai parts, let's determine which of the fuses is responsible for what in the car.
The Hyundai Accent has three fuse boxes. Two are in the cabin, and the third is under the hood.
Engine compartment fuse box. And a list of what each detail is responsible for.
Passenger compartment fuse box. It is located below the steering wheel, on the left. To get to it, remove the decorative strip on the torpedo.
The second block is located behind an additional glove compartment in the cabin. There are relays that protect powerful energy consumers in the car.
Relay number and what it is responsible for:
- Responsible for the distribution of braking forces. In the event of a breakdown during braking, the car “drives”.
- Responsible for the rear "fog".
- This is the main relay for Hyundai Accent. In the image, the relay is disconnected from the connector.
- Monitors headlight bulbs.
- Responsible for the operation of the windshield wiper and washer motor.
- Responsible for the work of ABS.
- Responsible for the operation of the power windows.
- Responsible for the rear window heating mechanism.
- Responsible for the operation of the steering horn.
- Provides the operation of turn signal lamps and light signaling.
Any novice motorist can change the fuse.
- Disconnect the battery first. Open the hood and remove the negative terminal.
- Now open the cover of the mounting block. You can pry it off with a flat screwdriver or some other handy tool.
- Now you need to check the fuse. Pull it out with tweezers or hands and check it visually. There is a fusible thread inside the fuse. It can break off or burn out. Such a component becomes unusable.
Remember! The new fuse must be of the same rating as the one removed.
- Now check if the problem is fixed by connecting the battery. If so, remember to replace the cover.
The on-board network of the car is direct current, with a nominal voltage of 12 V. The electrical equipment is made according to a one-wire scheme: the “negative” terminals of the sources and consumers of electricity are connected to the “ground”: the body and the main units, which perform the function of the second wire. When the engine is not running, the switched on consumers are powered by the storage battery, and after starting the engine - from an alternator with a built-in rectifier and an electronic voltage regulator. When the generator is running, the battery is charged.
All electrical circuits of the vehicle (except for the starter power circuit) are protected by fuses installed in the fuse box in the passenger compartment and in the fuse and relay box in the engine compartment. Powerful consumers (headlights, electric motor of the cooling fan, electric fuel pump, etc.) are connected via relays installed in the relay box in the passenger compartment and the mounting block of relays and fuses in the engine compartment.
Hyundai Accent (TagAZ). M FUSE AND RELAY MOUNTING BLOCKS
The relay and fuse mounting block is located on the left in the engine compartment. The location of the fuses and relays is indicated on the outside of the cover. The passenger compartment relay box is located under the dashboard behind the additional glove compartment. To replace the relay, open the clothing
Mounting block for relays and fuses in the engine compartment:
1 - fuse 100 A generator circuit; 2 - 50 A complex fuse (circuits of the electric drive of door interlocking, alarm, brake signals,rear window heating,sound signal, interior lighting lamps, ECU);3 - fuse 30 And the chains head and side light lamps;4 - fuse 20 A control unit circuit engine; 5 - fuse 30 A for the engine start circuit and ignition coils.6 - fuse 20 A fan circuit radiato ra engine cooling system,7 - wiring connector,8 - fan relay ra heater. 9 - horn relay,10 - fuse 10 A interior lamp circuits. 11 - 10 A fuse for the system head unit sound reproduction.12 - relay 2 condenser coil fan systems air conditioning,13 - clutch relay air conditioning compressor,14 - fog relay socket headlights; 15 - backup fuse socket;16 - 15 A fuse for the idle speed regulator and the camshaft position sensor.17 - fuse 10 A circuit of the engine control unit.18 - radiator fan relay of the engine cooling system;19 - 10 A fuse for the air conditioner switching circuit;20 - relay 1 of the fan of the heat exchanger of the condenser of the air conditioning system;21 - fuse 10 A for the circuit of the engine control unit,22 - fuse 10 A for the air conditioning compressor clutch circuit,23 - fuse 10 A horn circuit;24 - 15 A fuse for the fog lamp circuit.25 - 10 A fuse for the right head lamp circuit.26 - 10 A fuse for the left head lamp circuit;27 - fuse 10 A for the side light lamp circuit of the right side of the car;28 - fuse 10 A left side side light bulb circuits car ; 29 - position lamp relay Sveta; 30 - generator pre-excitation resistor; 31 - starter relay, 32 - fuse 20 A fan circuit condenser heat exchanger sieem kinitslimirovanny, 33 - prefilter 30 A of the electric window chain. 34 35 - socket of the relay of the permanently switched on dipped beam; 36 - fuel pump relay; 37 - fuse 30 A circuit of the ABS control unit; 38,39 - diode socket; 40 - fuse 30 A for the heater fan circuit
Passenger compartment relay box:1 - turnip electronic brake force distribution (EBD); 2 - fog light relay in the rear lights,3 - the main relay of the engine control system (for clarity, the mount is disconnected);4 - head lamp relay;5 - relay of a cleaner and washer of a windshield;6 - ABS relay; 7 - power window relay;8 - rear window heating relay,9 - buzzer relay;10 - direction indicator and alarm relay
Lift the box and remove it from the latches, opening access to the relay.
To access the fuse box, open the protective cover under the dashboard to the left of the driver's feet. On the inside of the cover there is a diagram of the location of the fuses in the block. Replacing the relays and fuses is carried out in the same way as described in Sect. (cm. " Replacing the relays and fuses of the engine management system", with. 74).
Fuse mounting blockbodies in the cabin: 1 - 10 A fuse for the direction indicator circuit;2 - 10 A fuse for ABS circuits, control lamps in the instrument cluster;3 - 10 A fuse for the instrument cluster circuit;4 - 15 A fuse for the airbag circuit;5 - 10 A fuse for the circuits of the engine control unit, reversing light lamps, automatic transmission control unit;b- 10 A fuse for the electric drive circuit of the door interlock;7 - 10 A fuse for the alarm circuit;8 - 10 A fuse for the brake signal circuit;
9 - fuse 20 A for the rear window heating circuit.10 - fuse
10 A circuits of the windings of the relay block headlights. power windows, headlight block washer, air conditioning condenser heat exchanger fan, engine cooling radiator fan, fog lights. fog light in the rear lights .11 - 20 A fuse for the windshield wiper and washer circuit. 12 - 10 A fuse for the seat heating circuit (optional), 13131 134 ..
4.5 Rating 4.50 (2 Votes)
In Hyundai Accent, as in any other car, fuses are a kind of protection for the electrical equipment of the car. If the wiring is short-circuited, they may burn out. In this case, it is enough to replace one of the elements of the fuse block, and you can continue to enjoy a comfortable ride.
To eliminate the incorrect operation of the cigarette lighter, brake light or dimensions, you need to know the location and number of the fuse responsible for the failed electrical circuit. This car has 2 blocks with protective elements.
Hyundai Accent fuse box under the hood. 
In the engine compartment, a block with protective devices and relay located behind the battery. Its cover is secured with plastic clips. After opening you can see fuse location and also extract the desired item. The block has a special tweezers for removing burnt parts.
Fuse box in the passenger compartment Hyundai Accent 
In the cabin, the protective elements are located on the torpedo (on the left side of the steering wheel). The block contains fusible links that are responsible for the electrical appliances in the passenger compartment, for example, cigarette lighter, signal fuse, door opening lamps, etc. To remove the burned-out device, just open the plastic cover. On the inside, it has a diagram that indicates fuse location in the block.
Possessing the above information, you can eliminate the breakdown of one of the electrical appliances in a car of this brand without additional costs. Now you will no longer have any questions about where to look for a fuse and how to replace it.
DESCRIPTION OF THE DESIGN of electronics and electrical equipment Hyundai Accent (Hyundai Accent)
The on-board network of the car is direct current, with a nominal voltage of 12 V. The electrical equipment is made according to a one-wire scheme: the "negative" terminals of the sources and consumers of electricity are connected to the "ground": the body and the main units that perform the function of the second wire. When the engine is not running, the switched on consumers are powered by the storage battery, and after starting the engine - from an alternator with a built-in rectifier and an electronic voltage regulator. When the generator is running, the battery is charged.
All electrical circuits of the vehicle (except for the starter power circuit) are protected by fuses installed in the fuse box in the passenger compartment and in the fuse and relay box in the engine compartment. Powerful consumers (headlights, electric motor of the cooling fan, electric fuel pump, etc.) are connected via relays installed in the relay box in the passenger compartment and the mounting block of relays and fuses in the engine compartment.
MOUNTING BLOCKS FOR RELAYS AND FUSES Hyundai Accent
The relay and fuse mounting block is located on the left in the engine compartment. The location of the fuses and relays is indicated on the outside of the cover. The passenger compartment relay box is located under the dashboard behind the additional glove compartment. To replace the relay, open the clothing
Mounting block for relays and fuses in the engine compartment:
1 - fuse 100 A of the generator circuit; 2 - 50 A complex fuse (electric drive circuits for door locking, alarm, brake signals, rear window heating, sound signal, interior lighting lamp, ECU); 3 - fuse 30 A of the lamp circuit of the head and side light; 4 - fuse 20 A circuit of the engine control unit; 5 - fuse 30 A of the engine start circuit and ignition coils; b - fuse 20 A for the radiator fan circuit of the engine cooling system; 7 - wiring connector; 8 - heater fan relay; 9 - horn relay; 10 - fuse 10 A of the interior lighting lamp circuit; 11 - 10 A fuse of the head unit circuit of the sound reproduction system; 12 - relay 2 of the fan of the heat exchanger of the condenser of the air conditioning system; 13 - air conditioning compressor clutch relay; 14 - socket of the relay of fog lights; 15 - backup fuse socket; 1b - 15 A fuse for the idle speed regulator and the camshaft position sensor; 17 - fuse 10 A for the circuit of the engine control unit; 18 - relay of the radiator fan of the engine cooling system; 19 - 10 A fuse for the air conditioner switching circuit; 20 - relay 1 of the fan of the heat exchanger of the condenser of the air conditioning system; 21 - 10 A fuse for the engine control unit circuit; 22 - fuse 10 A of the air conditioning compressor clutch circuit; 23 - 10 A fuse for the horn circuit; 24 - 15 A fuse for the fog lamp circuit; 25 - fuse 10 A of the circuit of the right head lamp; 26 - fuse 10 A circuit of the left head lamp; 27 - fuse 10 A of the chain of side light lamps of the right side of the car; 28 - fuse 10 A of the side light lamp circuit of the left side of the car; 29 - side light lamp relay; 30 - generator pre-excitation resistor; 31 - starter relay; 32 - fuse 20 A for the fan circuit of the air conditioning condenser heat exchanger; 33 - fuse 30 A of the electric window chain; 34 - fuse 30 A circuit of the ABS control unit; 35 - socket of the relay of the permanently switched on dipped beam; 36 - fuel pump relay; 37 - fuse 30 A circuit of the ABS control unit; 38.39 - diode socket; 40 - fuse 30 A heater fan circuit
drawer, lift and remove it from the latches, opening access to the relay.
To access the fuse box, open the protective cover under the dashboard to the left of the driver's feet. On the inside of the cover there is a diagram of the location of the fuses in the block. Replacing the relays and fuses is carried out in the same way as described in Sect. (see "Replacing the relays and fuses of the engine management system", page 74).
IGNITION SWITCH Hyundai Accent
The ignition switch is non-separable. The switch housing is made integral with the steering column - to replace it, the column must be replaced. An immobilizer sensor is installed on the ignition switch.
REMOVING THE CONTACT GROUP OF THE IGNITION SWITCH Hyundai Accent (Hyundai Accent)
Remove the upper and lower steering column covers. To do this, lower the steering column tilt adjustment lever.
Use a Phillips screwdriver to unscrew the three screws securing the lower casing.
We pry off the upper casing with a screwdriver, placing a rag under it to avoid scratching.
Disconnect and remove the upper and lower covers.
The covers are held together with plastic clips.
Disconnect the wiring harness block of the contact group.
We release the plastic clamp of the ignition switch.
Disconnect the immobilizer wiring block.
Use a Phillips screwdriver to unscrew the screw that secures the immobilizer.
We remove the immobilizer.
Use a Phillips screwdriver to unscrew the screw that secures the contact group.
We remove the contact group.
Install the contact group of the ignition switch in reverse order. When assembling, pay attention to the fact ...
… So that the groove in the contact block matches the tab of the ignition switch.
BATTERY Hyundai Accent (Hyundai Accent)
A low-maintenance lead starter battery with reverse polarity is installed on the car (if the "minus" terminal is facing the left side of the car, then both terminals are located closer to the bulkhead), the nominal voltage of which is 12 V. The nominal capacity at a 20-hour discharge mode is 55 Ah ... The battery case is made of translucent plastic. When working with the battery, strictly follow the safety instructions (see "Safety during maintenance and repair" p. 11).
REMOVING THE BATTERY Hyundai Accent
Using the “10” key, we loosen the fastening of the “negative” wire terminal at the battery terminal and remove the terminal.
ALTERNATOR GENERATOR REMOVAL Hyundai Accent (Hyundai Accent)
DESCRIPTION OF THE CONSTRUCTION
The generator is a three-phase synchronous AC electric machine with electromagnetic excitation, with a built-in silicon diode rectifier and an electronic voltage regulator.
Lifting the protective cover ...
... in the same way we remove the terminal of the "positive" wire.
Using the "12" head with an extension cord, unscrew the bolt ...
... and remove the retaining clip.
The generator label indicates the current and voltage supplied by the generator.
The alternator rotor is driven from the engine crankshaft pulley by a poly V-belt.
The stator and generator covers are tightened with four bolts. The rotor shaft rotates in bearings installed in the covers. The bearings are lubricated at the factory for the life of the generator. The excitation winding of the generator is located on the rotor. Its leads are soldered to two copper slip rings on the rotor shaft. Power to the field winding is supplied through carbon brushes. The brush holder is structurally integrated with a voltage regulator.
The generator windings and rectifier unit are cooled by two impellers located on the rotor. The back of the generator is covered with a plastic cover.
We take out the battery from the engine compartment.
Install the battery in reverse order.
Generator
Disconnect the negative wire terminal from the battery terminal.
Remove the alternator drive belt (see "Adjusting the tension and replacing the alternator drive belt", p. 38). By pressing the latch ...
… We disconnect the block of wires.
By pressing the latch ...
… Open the protective cap of the “B +” terminal of the generator.
Using the "12" head, unscrew the wire fastening nut ...
... and remove it from the generator output "B +".
STARTER. REMOVAL OF THE STARTER Hyundai Accent (Hyundai Accent)
Using the "12" head, we unscrew the bolt fastening the generator to the adjusting bar ...
… And remove the alternator belt tensioner.
Remove the oil filter (see "Changing the engine oil and oil filter", p. 31). We unscrew the nut of the lower mounting bolt of the generator by several turns. Lifting the generator ...
... remove the bolt from the slot of the oil pump housing ...
... and remove the generator.
We install the generator in the reverse order and check the tension of the drive belt (see "Adjusting the tension and replacing the alternator drive belt", p. 38).
DESCRIPTION OF THE STRUCTURE Starter on Hyundai Accent (Hyundai Accent)
On Hyundai Accent car (Hyundai Accent) installed starter, which is a four-pole, four-brush DC motor with permanent magnet excitation, with a planetary gearbox, a roller freewheel clutch and a two-winding traction relay.
To the steel body starter permanent magnets are attached. Starter housing and covers are tightened with two bolts. The armature shaft rotates in plain bearings. The torque from the armature shaft is transmitted to the drive shaft through a planetary gearbox. A freewheel (freewheel) clutch with a drive gear is installed on the drive shaft. It transmits torque in only one direction: from starter to the engine, disconnecting them after starting the engine.
This is to protect the gearbox and starter armature from damage from overspeed.
The traction relay is used to engage the drive gear with the gear ring of the flywheel of the engine crankshaft and turn on the power to the starter motor, which occurs when the ignition key is turned to the "START" position (in a car with an automatic transmission, the gear selector must be in the "P" positions or "N"). After the contacts of the traction relay are closed, the retraction winding is turned off.
Disconnect the negative wire terminal from the battery terminal.
It is more convenient to remove the starter from a car installed on a viewing ditch or overpass.
Disconnect the wire block from the starter.
Using the "12" head, unscrew the nut ...
… And disconnect the tip of the wire from the starter terminal.
Using the “14” head, we unscrew the two fastening bolts (the lower bolt also secures the tip of the “mass” wire) ...
…. and remove the starter.
To replace the traction relay ...
... with a key "12" we unscrew the nut securing the wire tip to the output of the traction relay ...
... and remove the tip from the output.
Use a Phillips screwdriver to unscrew the two fastening screws ...
… And remove the starter traction relay.
Install traction relay for starter and starter on the vehicle in reverse order.
Hyundai Accent EXTERIOR LIGHTING, LIGHT SIGNALS, INTERIOR AND TRUNK LIGHTING, SOUND SIGNAL
The car has two headlights. The headlight unit contains lamps for head light, direction indicator and side light. Head lamp (low and high beam) - double-stranded, halogen; direction indicator lamp - single-strand, with an orange bulb; side light lamp - baseless. The car is equipped with a headlight range control with an electromechanical drive, which allows you to adjust the direction of the light beam depending on the load of the car. The headlight range control consists of a regulator on the instrument panel, electric drives installed in the headlights, and connecting wires.
The car can be equipped with fog lights. Reversing lights come on when the ignition is on and reverse gear is engaged. Removing the lamp, replacing the side light bulb and brake signal, see Sect. "Replacing the head and side light bulbs in the headlight unit, the combined side light bulb and the brake signal in the rear light", (p. 46). The rest of the lamps installed in the rear light can be replaced in the same way.
When the brake pedal is depressed, the braking signals are switched on automatically by a switch installed in the pedal assembly bracket. All switches cannot be repaired; if they fail, they are replaced with new ones. The sound signal is attached to a bracket on the upper cross member of the radiator frame. The signal is activated by a button on the steering wheel. If necessary, you can adjust the sound of the signal by turning the adjusting screw.
REPLACING LAMPS UNIT HEADLIGHTS Hyundai Accent (Hyundai Accent)
You can replace bulbs without removing the headlights from the car. For clarity, the work is shown on the removed headlamp.
Replacement of head and side light bulbs is shown in section. "Replacement of lamps for the head and side light in the headlamp unit, the combined side light lamp and the brake signal in the rear lamp"
To replace the turn signal bulb ... 
... turn the lamp holder counterclockwise by 45 ° ...
… And take it out of the headlight housing.
Having pressed the lamp, we turn it counterclockwise all the way ...
... and take the lamp out of the socket.
REMOVING THE HEADLAMP UNIT
Disconnect the negative wire terminal from the battery terminal.
By pressing the latch ...
... turn signal ...
… We disconnect the block of wires from the drive of the electrocorrector.
We disconnect the pads of wires from the lamps ...
… Head and side light (see "Replacing the head and side light bulbs in the headlamp unit, the combined side light bulb and the brake light in the rear light", p. 46). Turn off the head "by 10" ...
… Two bolts of the headlight unit.
Use a Phillips screwdriver to unscrew the retainer ...
… And take out the front panel top mount piston.
We remove the headlamp unit from the car.
Install the headlamp in reverse order. We check and, if necessary, adjust the headlights (see "Adjusting the direction of the headlights" p. 44).
REMOVING THE DRIVE OF THE ELECTRIC CORRECTOR OF THE HEADLAMP UNIT Hyundai Accent (Hyundai Accent)
To remove the drive of the electric corrector of the left headlamp unit, it is necessary to remove the storage battery (see "Removing the storage battery").
Disconnect the block of wires from the drive of the electrocorrector (see "Removing the headlight unit"). For clarity, we show the work on the removed headlamp.
We turn the actuator 90 ° so that its connector moves to the upper position.
Use a slotted screwdriver to unscrew the adjusting screw ...
… And remove the drive from the hole in the headlamp housing.
Headlight unit electric corrector drive
Install the drive in reverse order.
REMOVING THE SIDE TURN INDICATOR, REPLACING THE LAMP Hyundai Accent (Hyundai Accent)
Remove the liner from the side of the lamp being replaced. To replace the side turn signal bulb ...
We take out the lamp holder from the indicator housing.
We remove the lamp from the socket.
Install the direction indicator lamp in reverse order.
To remove the direction indicator by pressing the latch ...
… Disconnect the wiring block from the indicator holder.
Pressing the latch with your finger ...
... push the back of the pointer out ...
… And remove the pointer from the car.
Install the side direction indicator in the reverse order.
REMOVING THE SWITCH OF THE REVERSE LIGHTS Hyundai Accent (Hyundai Accent)
For clarity, we show the work on the removed gearbox. To remove the reversing light switch, disconnect the wiring block from the switch.
Turn off the switch with the "24" key ...
... and take it off.
The seal of the circuit-breaker is not structurally provided. Install the switch in reverse order.
REMOVING THE LIGHT OF THE REAR NUMBER PLATE, REPLACING THE BULB Hyundai Accent (Hyundai Accent)
To remove the flashlight ...
… And remove the cover.
From the inside of the trunk lid ...
… Use a Phillips screwdriver to unscrew the three self-tapping screws for the boot lid trim…
By pulling the lamp along the axis of the socket ...
… We disconnect the block of wires from the socket of the lantern.
… We take out the lamp.
We replace the burnt out lamp with a new one.
REMOVING THE LIGHTING OF THE INTERIOR LIGHTING, REPLACING THE LAMP Hyundai Accent (Hyundai Accent)
... take out the lamp.
Install the lamp in reverse
sequence.
To remove the plafond, remove it
diffuser.
Using a Phillips screwdriver, unscrew the two self-tapping screws for attaching the lantern to the trunk lid ...
Use a Phillips screwdriver to unscrew the two screws securing the lamp housing ...
... gently pry with a screwdriver ...
… And take out the lantern from the hole in the cover.
We carry out the installation of the lantern in the reverse order. To replace the lamp on the inside of the trunk lid, turn its cartridge counterclockwise ...
… And remove the lamp housing from the headlining.
… And remove the diffuser of the plafond.
… And remove the lamp holder from the diffuser body.
By pressing the spring contact of the plafond ...
By pressing the latch ...
… Disconnect the wiring block from the lamp housing.
Install the interior lighting in the reverse order.
REMOVING THE UNDER-STEERING SWITCHES Hyundai Accent (Hyundai Accent)
We show the work on the example of a combined switch for headlights and direction indicators.
Disconnect the negative wire terminal from the battery terminal. Remove the upper and lower steering column covers (see "Removing the ignition switch contact group").
Disconnect the wiring block from the steering column switch.
Use a Phillips screwdriver to unscrew the two self-tapping screws of the steering column switch to the connector ...
... and take out the switch.
Install the steering column switch in reverse order.
The switch for the wiper and washer of the windshield is removed in the same way.
REMOVING THE AUDIBLE SIGNAL Hyundai Accent (Hyundai Accent)
Having opened the hood, we fix it with an emphasis.
Using the "10" wrench, unscrew the nut that secures the sound signal plates to the upper cross member of the radiator.
Pressing the latches ...
… Disconnect the block of wires from the sound signal. Using the "13" wrench, unscrew the nut securing the sound signal to the plates ...
... and shoot them.
The sound of the signal is adjusted with a screw (shown by an arrow).
We set the sound signal in reverse order.
REMOVAL OF THE REDUCED MOTOR OF THE WINDSHIELD CLEANER Hyundai Accent (Hyundai Accent)
Disconnect the negative wire terminal from the battery terminal.
We recessed the clips of the two plugs of the right windshield lining.
We take out the plugs ...
… And remove the cover.
We remove the protective grill of the air inlet box.
Disconnect the wiring harness block from the gear motor.
Using the "10" head with an extension cord, unscrew the four bolts of the gear motor.
Pulling out the geared motor, release the crank joint and remove the geared motor.
Using the "13" key, unscrew the crank fastening nut, holding it from turning with a screwdriver.
Remove the crank
… And a sealing cover.
We carry out the installation of the geared motor in the reverse order. To install the shaft of the geared motor in its original position, put on the terminal of the "minus" wire to the battery terminal. We connect the block of wires to the gear motor and turn it on with the steering column switch, then turn it off and wait for the motor shaft to stop. Disconnect the wiring block from the geared motor. In this position of the gear motor shaft, we set the crank like this ...
... as shown in the photo.
Holding the lever through the window in the air intake box from moving ...
… Insert the ball pin of the crank into the hole in the lever until it is in a fixed position.
The further installation of the windshield wiper gear motor is carried out in the reverse order.
REMOVING THE ELECTRIC PUMP OF THE WINDSHIELD WASHER on Hyundai Accent (Hyundai Accent)
Remove the right front wheel arch liner (see "Removing the front wheel arch liner", p. 142). By pressing the latch ...
… Disconnect the wiring block from the windshield washer pump.
Remove the fluid supply hose to the windshield nozzles from the electric pump nozzle.
We remove the electric pump from the tank.
Install the windshield washer electric pump in reverse order.
REMOVAL OF INSTRUMENT COMBINATION, REPLACEMENT OF LAMPS Hyundai Accent (Hyundai Accent)
Disconnect the negative wire terminal from the battery terminal.
We set the steering column to the lowest position.
Use a Phillips screwdriver to unscrew the two self-tapping screws ...
… And remove the instrument cluster cover.
With the same tool, we unscrew the four self-tapping screws for fastening the instrument cluster ...
... and slide it onto ourselves.
In this case, the shank of the speedometer drive cable will come out of the hole in the instrument cluster.
By pressing the latch ...
… Disconnect the wiring block from the instrument cluster connector.
Disconnect the rest of the wiring blocks in the same way ...
… And remove the instrument cluster.
The pads of the wires are different, so it is impossible to confuse them when connecting.
To replace the backlight or indicator lamp in the instrument cluster ...
... turn the lamp holder counterclockwise ...
... and remove it together with the lamp from the socket in the circuit board of the instrument cluster.
We take out the lamp from the socket.
Green light filters are installed on the bulbs of the instrument cluster illumination lamps.
When replacing the lamp with a new one, we rearrange the light filter. Install the lamp in reverse order. We replace the control lamps together with the cartridges. Install the instrument cluster in reverse order.
Wherein…
… The end of the speedometer cable must enter the corresponding hole in the instrument cluster.
REMOVAL OF THE ELECTRIC FAN HEATER Hyundai Accent (Hyundai Accent)
Disconnect the negative wire terminal from the battery terminal.
Open the glove box and remove the clips of its limiters (see "Removing the glove box").
Use a Phillips screwdriver to unscrew the four self-tapping screws ...
... and remove the glove box with the mounting plate.
We take out the wiring harness of the fan motor from the clamp ...
… And disconnect the block.
Using a Phillips screwdriver, unscrew the three self-tapping screws that secure the fan motor cover to the fan housing ...
... and take out the fan impeller complete with electric motor and cover.
Before installing the heater electric fan, we clean the cavity of the guide casing from dirt.
Install the heater fan in reverse order.
REPLACING THE RESISTOR OF THE FAN HEATER Hyundai Accent (Hyundai Accent)
Disconnect the negative wire terminal from the battery terminal.
Remove the glove box together with the mounting plate (see "Removing the heater fan").
Disconnect the wiring harness block (A) from the heater fan resistor and unscrew the two self-tapping screws (B) securing the resistor. Remove the resistor.
Heater fan resistor
Install the resistor in reverse order.
On Hyundai Solaris cars of the first generation of 2010, 2011, 2012, 2013 and 2014, 2 distribution blocks with fuses and relays are installed.Location of all blocks in the car
Let's consider the decoding of block diagrams in detail. The designations indicate what each of them is responsible for.
1. Fuse box under the hood
Fuse | Terminal | Current (A) | Appointment |
Fuel pump |
|||
Sound signal |
|||
Switching unit: emergency gang, power windows, central locking, fuses - F23-F25, F31, F32 |
|||
Heating system control unit |
|||
Engine control unit - relay 1. Fuse F25 |
|||
ACC - relay. Ignition lock, body electrical control module, automatic transmission lock control module, start-stop button control unit. IG2 - relay |
|||
Ignition switch, body electrical control module, automatic transmission lock control module, control unit start-stop button |
|||
Air conditioning |
|||
Engine control module. Transmission control module. Fuel pump - relay. Oil control valve |
|||
Engine control module. Camshaft sensor. Oxygen sensor. Immobilizer. Air conditioner - relay. Fan - low speed relay and high speed relay. Solenoid valve |
|||
Transmission control unit. Automatic transmission sensor. Dashboard. Combined rear lights. |
|||
| Relay |
|
| Location | Designation |
| Reserve | |
| Horn relay | |
| Air conditioner relay | |
| Ignition interlock switch relay | |
| Fan relay (low speed) | |
| Fan relay (high speed) | |
| Diagnostic connector relay | |
| Ignition switch relay | |
| Ignition switch relay, body electrical control module, automatic transmission lock control module, engine start and stop button control unit | |
| Emergency brake warning relay | |
| Relay, electronic engine control unit | |
| Fuel pump relay | |
| Reserve | |
| Radiator fan relay | |
1.2 Main multi-fuse with jumpers
The multi-fuse serves to optimize the layout of the engine compartment.
2. Fuse box in the passenger compartment, dashboard
Fuse | Terminal | Current (A) | Appointment |
Heated windshield |
|||
12V socket |
|||
Cigarette lighter |
|||
Ignition switch - audio system, body electrical control module, automatic transmission lock control module, electronic key system control unit |
|||
Airbag deactivation indicator - front |
|||
Airbags, SRS control module |
|||
Emergency light signaling |
|||
Rear window wiper - engine Multifunction switch |
|||
Fog lights (rear) |
|||
Fog lights (front) |
|||
Battery saving relay (automatic circuit breaker) |
|||
Stop lights |
|||
Instrument cluster |
|||
Security System Control Module |
|||
ABS hydroelectronic module |
|||
Rear running lights (switch) |
|||
Control module body electrical control module, automatic transmission lock control module, electronic key system control unit |
|||
Headlight - left |
|||
DAY TIME RUNNING LIGHT | Daytime Running Lights |
||
Alarm switch |
|||
Control module body electrical control module, automatic transmission lock control module, electronic key control unit |
|||
Control module body electrical control module, automatic transmission lock control module, electronic key control unit, engine start / stop button switch |
|||
Speed sensor Automatic transmission range sensor. Pulse generator |
|||
Ignition coil 1-4, capacitor |
|||
Power windows. Luke |
|||
Windshield wiper |
|||
Central locking - control unit |
|||
Power windows - blocking |
|||
Heated front seats |
|||
Interior lighting. Air conditioning |
|||
Audio system |
|||
Headlight and lantern on the port side. License plate lighting |
|||
Headlight and lantern on the starboard side. Illumination of switches, switches in the cabin, selector lever. Instrument cluster, power and switch buttons |
|||
Starter - relay. Anti-theft alarm |
|||
Headlight - right |
|||
Power Window Control Unit - Left Rear Switch |
|||
Power Window Control Unit - Right Rear Switch |
Keep useful materials for yourself!
