When choosing a wheel for a Mazda car, special attention should be paid to the parameters of wheels and tires. For each car model, Japanese manufacturers use their individual standard sizes. For example, the factory equipment of the Mazda 6 assumes the use of 195/65 / R15 tires. Alternatively, you can use tires 205/50 / R17, 205/60 / R15, 225/40 / R18, 225/35 / R19.

Wheel sizes for Mazda 6 I GG

• an increase in the load on the hub bearings;
• loss of aerodynamic performance;
• decrease in vehicle stability.

In addition, such indicators as fuel consumption, handling and safety while driving a car depend on the choice of wheel sizes.

Before choosing a wheel for a Japanese car, you need to study its parameters:

1. tire width;
2. profile height;
3. speed and capacity indices;
4. tire pressure;
5. diameter;
6. departure;
7. number of fasteners;
8. types of fasteners;
9. circle parameters;
10. centering hole.

When choosing custom wheel sizes, you can use a tire calculator. This device is able to select the optimal sizes of disks and tires, wheel load index, taking into account the vehicle speed and the amount of ground clearance.

Wheel sizes for Mazda 6 GG version 2002-2008:

1. thread diameter: 5.

The size of car tires for Mazda 6 GG

Here is a table where we indicate the indices of wheel load, speed, dimensions and pressure in tires on the GG version.

Wheel Load Index	Tire parameters	Tire pressure kg / cm²	Speed ​​index
91	195/65 / R15	2.2	V
93	205 / 60R16	2.2	V
Replacement
91	215/45 / R17	2.2	V
91	215/50 / R17	2.2	V
89	215/45 / R18	2.2	W
91	225/45 / R18		W

Wheels for Mazda 6 GG

	The size	Disc departure
5 × 114.3	6Jx15	ET50
5 × 114.3	6.5Jx16	ET55
Replacement
5 × 114.3	6.5Jx16	ET55
5 × 114.3	7Jx16	ET55
5 × 114.3	7Jx17	ET55
5 × 114.3	7Jx17	ET60
5 × 114.3	7Jx17	ET60
5 × 114.3	7Jx18	ET55
5 × 114.3	7.5Jx18	ET60

Wheel sizes for Mazda 6 II GH

• 205 denotes the width of a car tire. This indicator is measured in millimeters and is determined by calculating the distance of the lateral edges of the inflated tire. This does not include protective belts;
• 60 shows the profile height of a tire, measured as a percentage of the width of an automobile tire. Thus, to determine the height, you need to know the ratio of 205 mm to 60%. As a result, we calculate the profile height: (60% / 100%) X 205 = 123 mm;
• R indicates the radiality of the tire. Translated from English, Radial is the radiality of a car tire. Thus, manufacturers assemble rubber and cord when creating a tire. Also, the letter D was used to designate the radiality. However, tires with this designation are practically no longer produced;
• 16 indicates the diameter of the rim center hole for which a car tire can be used. This indicator is indicated in inches.

Mazda 6 GH 2007-2012 model year:

• center hole diameter DIA: 67.1 mm;
• hub fastener: nut;
• thread: M12x5.

Additional information indicated on the side of the tire:

M&S (Mud and Snow) translated from English mud and snow: off-season and winter tires;

XL (Extra Load) a reinforced tire with a wheel load index exceeding by 3 units ordinary tires with similar standard sizes;

AW or AS off-season tires;

Symbol * indicates that the tire is intended for winter use. If this marking is not indicated on the side of the tire, then the rubber is used only for the summer period;

Inside, Outside- the inner and outer side of the asymmetric tire. Accordingly, when installing a wheel, the Inside inscription should be located on the outside of the rubber, and the Outside indicator on the inside of the tire;

Water, Rain, Aquatred, Aqua or an umbrella-shaped symbol indicates rain rubber;

Tubeless lettering- tubeless tire. If the inscription is absent, it means that the bus is used with the camera. Tube Type Indicator - Tire is installed with a tube only;

Arrow or inscription Rotation demonstrates the direction of the tread pattern. Indicated on the side of the tire.

Wheel sizes for Mazda 6 III GJ

For the Mazda 6 III GJ car, the standard disc size marking is used, as for other models of Japanese cars.

Before choosing a wheeled product, it is necessary to study the standard parameters of a factory-fitted autodisk 7.5 × 17 5 × 114.3 ET50 for the GJ version, where:

• 7.5 demonstrates its width in inches;
• the J symbol indicates the design, the shape of the flanges;
• the number 17 indicates the diameter of the disc fit. This indicator should correspond to similar parameters of the tire;
• 5 × 3 - PCD disc bolt pattern. The number 5 indicates the number of holes for fastening the nuts, 114.3 indicates the diameter of the PCD circle;
• ET50 marking indicates a disc overhang with an indicator of 50 mm. Reach is the distance from the rim mating plane to the middle of the wheel rim. The zone where the wheel rim is pressed against the car hub is called the seating plane.

The following information is attached to the marking of wheel rims on Mazda GJ 2012-2015:

Max Load indicates the maximum permissible wheel load;

ISO, TUV, SAE - classification standards for determining the quality of the disc, similar to GOST. For each product, one or another quality standard is indicated;

Center hole diameter DIA: 67.1 mm. This indicator should correspond to the diameter of the hub fit. For casting, manufacturers use a large centering hole. So that the wheels can be universal for all types of cars.

However, in this situation, the hub seating diameter and DIA differ from each other. Therefore, it is recommended to use a centered adapter ring as a connecting element.

The correct choice of wheel size also depends on the ability to determine the marking of the rim and tire. If the car owner does not know the marking designation, then the selected tires or wheels may not fit in size.

Wheel sizes for Mazda 6 III GL

The Mazda 6 GL version has been produced since 2015. Wheel parameters:

hub fastener: nut;

thread M12x1.5;

Tires for Mazda III GL

Wheels for Mazda III GL

Pay attention to the fact that the drill or bolt pattern indicates the fit of the rim diameter. In the operating instructions for cars, Japanese manufacturers indicate PCD, the landing diameter.

On Mazda cars, 3 different versions and editions use the same disc bolt pattern: 5 × 114.3. So this drill determines that the disc is 5 bolted and has a diameter of 114.3 mm.

Mazda 3 wheel sizes

	Diameter, R	Tire size	Disk departure, ET	Disc width, J
5 × 114.3	R15	195/65/15	45-55	66.57.0
5 × 114.3	R16	205/55/16	40-5540-5542-55	6.577.5
5 × 114.3	R17	205/50/17215/45/17225/45/17	42-5545-5548-52	77.58
5 × 114.3	R18	215/45/18225/40/18215/40/18	42-5542-5545-52	77.58
5 × 114.3	R19	225/35/19225/35/19	45-5548-52	7.58
5 × 114.3	R20	225/35/20	45-48	7.5

The parameters of the wheels on the Mazda 3 I and II are almost identical. The differences are that higher arches are installed on the second version of the car.

Thus, the Mazda 3 II BL can be fitted with wheels with an offset of 35 and a width of 8. Standard parameters are wheels of 16.17 inches with a diameter of 6.5 mm.

Wheels for Mazda 3 2013, III generation BM

Drilling (PCD, bore diameter)	Diameter, R	Tire size	Disc width, J	Disk departure, ET
5 × 114.3	R16	205/60/16	6..5	50
5 × 114.3	R17	205/50/17	7, 7.5	52.5
5 × 114.3	R18	215/45/18	7, 7.5	50
5 × 114.3	R19	215/35/19	8	50
5 × 114.3	R20	235/30/20	8.5	45

Factory wheel sizes for Mazda 3 hatchback and sedan 2013-2017 model year are 16, 18 inches, depending on the configuration. Tires with standard sizes are installed: 215/45 / R18, 205/60 / R16.

Tire pressure on Mazda 3

When using R16 tires with a load of up to 3 passengers, the pressure of the front and rear wheels must be 2.5 bar. With a load of up to 5 passengers, the rear tire pressure is 3.2 bar and the front tire pressure is 2.8 bar.

R18 tires with a load of up to 3 passengers must have a pressure of 2.4 bar for the front wheels and 2.3 for the rear tires. Full load up to 5 passengers - rear wheel pressure 3 bar and front tire pressure 2.8 bar. Refer to the 3rd Generation Mazda 3 Owner's Manual for this information.

How to independently determine the drilling?

Wheel rim bolt determination method:

1. the number of fasteners (bolts) is calculated from the holes located on the disc. For example, Mazda 3 has 5 holes in the disc;
2. the calculation includes determining the distance between the inner walls of the holes and adding them to the resulting value of their diameter.

For example, having determined the number of bolts and the diameter of the holes, the car owner gets the value 5 × 114.3 for the Mazda 3.

An exception may be 18 inch wheels for the Mazda 3 with a front drive axle and an engine capacity of 2.0, as well as versions with all-wheel drive and a capacity of 2.5 liters.

Mazda CX5 wheel sizes

All configurations of the Mazda CX5, since 2012, use 17 and 19-inch alloy and steel wheels marked 17x7J ET50, 19x7J ET50:

• ET - disc overhang 50 mm;
• 7J - rim width;
• centering hole diameter - 67.1 mm and 5 holes for fastening bolts around the disk circumference 114.3 mm; PCD 5 × 3.

Wheels with non-standard parameters (- + 0.5) inches can be installed on the Mazda CX5.

Tires for Mazda CX5

If you use factory rims of 17, 19 inches, then for the CX5 model tires are selected with standard sizes: 225/55 / ​​R19 / 99 V, 225/65 / R17 / 102 V. Marking designation:

• 225 - rubber width;
• 55.65 - profile height of the tire;
• 99.102 - index of carrying capacity from 750 to 850 kg;
• V - wheel speed index up to 240 km / h;
• R - radial tire design.

If you choose tires according to the capacity index, then you must take into account the fact that the estimated weight per person is 75 kg. As a last resort, you can calculate the number of passengers and install tires with high carrying capacity.

Using automatic selection of tires and wheels for the car Mazda 6, you can avoid many problems associated with their compatibility and compliance with the recommendations of the car manufacturers. After all, they have a huge impact on a significant part of the vehicle's operational properties, primarily on handling, fuel efficiency and dynamic qualities. In addition, one cannot fail to note the importance of tires and rims as active safety elements. That is why their choice should be approached as responsibly as possible, that is, with knowledge of a number of parameters of these components.

Unfortunately, only a small part of car owners own such technical nuances. Regardless, the automatic selection system will prove to be extremely useful, as it will minimize the likelihood of incorrect selection of wheels or tires. And there is plenty to choose from, thanks to the widest range of such products presented in the Mosavtoshina online store.

The looseness of the Mazda 6 wheel rims is a widespread parameter that denotes the way the wheel is attached to the chassis of the vehicle. This prevalence is due to the fact that most Japanese and Korean car manufacturers define identical sizes and parameters of wheels and tires, so that it is easier for motorists to choose. The razbotka disks "Mazda 6" are provided by the factory in one version and is equal to 5 × 114.3 regardless of generation. As for the wheels themselves, depending on the year of manufacture, they were installed in sizes from R15 to R19. By choosing and installing a set of wheels on a car, you can greatly improve the exterior design and obtain a high level of handling and stability.

If you need to make certain improvements in the appearance or technical characteristics of your Mazda 6 car model, you must select only spare parts and components from authorized manufacturers. Every car enthusiast knows that the wheels are the main part of the exterior. Most of the design depends on their size, color and shape. Not only the exterior of the car depends on the method of their manufacture, but also the driving qualities, which is much more important than the appearance. A vehicle with large rims looks more attractive than a similar one with small ones.

Mazda 6 bolt pattern, configurator

Improving the car's appearance is of course important, but it is not a top priority. For any type of transport, it is more important that changes in the original design do not reduce efficiency and resource. It is recommended to select only those spare parts and elements that would meet the factory specifications and safety requirements.

In addition to good looks, the installed wheels should be suitable for all parameters of wheel bolt pattern Mazda 6 2006, or any other model year. In addition, there must be full compliance with the established factory dimensions of the products. Inconsistency of the required parameters leads to incorrect and unsafe vehicle operation. Incorrectly chosen bolt pattern "Mazda 6" leads to the fact that the purchased discs simply do not fit, and they will have to be returned back. This gives the car owner unnecessary trouble. There are ways, for example, using adapter rings - this allows you to install even unsuitable wheels. However, in this case, movement will be a constant risk to the safety of the driver and passengers.

With the change in the size and parameters of the rims, it is necessary not to forget about the correct selection of a new set of tires.

Pitch Circle Diameter (PCD) stands for Pitch Circle Diameter. The value implies the number of bolts that are used to attach the product to the undercarriage and the diameter of the circle on which the bolts are located in relation to each other. When choosing a new set of wheels, it is necessary to consider this parameter as carefully as possible. Otherwise, if you do not know, there is a big risk of buying unsuitable products. It doesn't matter who the manufacturer of the new discs is, it can be original models or products from any other manufacturer. All of them must correspond to the permissible parameters and dimensions.

This parameter can be measured independently. A simple ruler will suffice for this, but for maximum accuracy it is better to use a vernier caliper. There are no problems with the number of bolts, they are very easy to calculate visually. But with the size of the diameter, difficulties arise. It requires high measurement accuracy and knowledge of special formulas to determine the parameter. It is best to look at it in the official technological documentation for the vehicle or pick it up according to the tables presented on the Internet.

Incorrectly selected and installed wheels for any car is a high risk of a threat to the safety of the driver and passengers.

In the best case, low-quality products will increase the wear of parts and suspension assemblies, and in the worst case, it can cause an accident.

Mazda 6 latest generation

Parameters for other models

The popular CX 5 from Mazda is a midsize crossover with increased weight compared to the sixth model. The importance of the disks is even greater for her than for the sedan. Therefore, it is very important to use only high quality and official products for improvement and tuning.

Note!

On "Mazda CX-5" discs are installed in only two sizes - R17 and R19.

In addition to the dimensions in terms of the diameter and width of the rim, there are no cardinal differences in parameters from the Mazda 6. It is necessary to consider what parameters of the bolt pattern "Mazda CX 5":

• 17-inch with parameters - 5 × 114.3; 7 × 17; ET50; d67,1. Tires 225/65 / R17;
• 18-inch with parameters - 5 × 114.3; 7 × 18; ET50; d67,1. Rubber 225/60 / R18;
• 19-inch, having parameters - 5 × 114.3; 7 × 19; ET50; d67,1. Rubber 225/55 / ​​R19.

The Mazda CX-7 car is equipped with the following wheels:

• Rim diameter - 18 inches;
• Width - 7.5 inches;
• Fasteners - 5 bolts x 114.3 mm;
• Departure - 50 mm;
• The diameter of the central hole is 67.1 millimeters.

On a note.

In this case, the so-called wheel markings are indicated. On the original, it should be embossed on the inside.

It indicates:

• 5 × 114.3 - the number of mounting holes and the diameter of the circle of their location, or bolt pattern;
• 7 × 17 - disc width and diameter, measured in inches;
• ET50 - disc offset, measured in millimeters;
• d67,1 - hub diameter, also indicated in millimeters.

The offset of the wheel is the distance between the planes of application to the hub and the center axle. This parameter is most important for calculating the characteristics of the steering and chassis.

"Mazda CX-5"

Departure parameters are specified by the vehicle manufacturer and must be strictly observed. A deviation in one direction or another entails a change in the loads on the chassis. This can lead to a change in steering sensitivity and possible emergency situations.

The hub diameter indicates the size of the disc center hole. It is measured in millimeters. If the selected set of wheels has a larger diameter, then it is necessary to purchase special adapter rings. They often come in a set.

Note!

Any deviations from the specified factory dimensions may affect steering performance and suspension wear.

Options for "Six"

As for the "Mazda 6", which was released in 2008, then when selecting disks for a car, the following are taken into account:

• The diameter of the rim, which is measured in inches.
• Rim width, also in inches.
• Outreach, measured in millimeters. This is the distance from the vertical axis of symmetry to the plane of contact between the hub and the disc.
• Number of holes for fastening with nuts and bolts, or just bolt pattern.
• Hole for the hub and its dimensions. Marked as DIA and represents the diameter of the center hole. Measured in millimeters.

Taking into account all the dimensions and parameters, the marking of the wheels can be distinguished:

• The bolt pattern, standard for Japanese manufacturers, is 5 × 114.3.
• Disc widths - 6.0, 7.0 and 7.5 J, depending on the radius, measured in inches.
• Departure of the disk - ET from 50 to 60, depends on the width, is measured in millimeters.
• The diameter of the central hole for the hub is d 67.1 millimeters.

For most of the lineup, Mazda engineers chose a bolt pattern of 5 × 114.3.

This makes it easy to select from a wide range of wheel rims on the market. There is an opportunity to choose both original products and products of various brands. The choice of sizes in width and diameter depends only on the personal preferences of the car owner. These dimensions are floating and subject to change. It is not recommended to change the bolt pattern and diameter of the center hole.

The size	Load index	Speed ​​index	Pressure, kgf / cm²
195 / 65R15	91	V	2.2
205 / 60R16	93	V	2.2
Replacement
205 / 55R16	91	V	2.2
205 / 55R16	91	V	2.2
215 / 45R17	91	W	2.2
215 / 50R17	91	V	2.2
215 / 50R17	91	W	2.2
215 / 45R18	89	W	2.4
225 / 45R18	91	W	2.2

Disk

The size	Departure	Drilling
6Jx15	ET50	5 × 114.3
6.5Jx16	ET55	5 × 114.3
Replacement
6.5Jx16	ET55	5 × 114.3
7Jx16	ET55	5 × 114.3
7Jx17	ET55	5 × 114.3
7Jx17	ET60	5 × 114.3
7Jx17	ET60	5 × 114.3
7Jx18	ET55	5 × 114.3
7.5Jx18	ET60	5 × 114.3

Mazda 6 II GH

205 – tire width. The indicator is calculated as the distance between the outer boundaries of the lateral surfaces of the inflated tire, excluding the protective belts. Measured in millimeters.

60 – the height of the tire profile, which measured as a percentage of the width. What does it mean? To find the height, you need to calculate 60% of 205 mm. This gives the tire height: 205 X 0.6 (60%) = 123.0 mm

R stands for radial tire. From the English word Radial, which means radial type of tire. It is a method of assembling rubber and metal cord during production. Of course, you can also find the letter D - diagonal, but such tires have now practically disappeared from production.

16 — the diameter of the hole in the rubber, or on which disc can this rubber be mounted, that is disc diameter. This dimension is always indicated in inches!

The diameter of the disc cannot be more or less than the diameter of the wheel, you simply will not wear it. That is, if the rubber is 16 inches (406.4 mm), then the disc must be 16 inches (406.4 mm)!

Additional Information

Mazda 6 GH, years of production: 2007 - 2012.

• Hub fasteners: nut;
• Thread: M12 x 1.5.

Additional information indicated in the marking on the sidewall of the tire:

• XL or Extra Load is a reinforced tire, the load index of which is 3 units higher than that of conventional tires of the same size.
• M + S or M&S (Mud + Snow) - mud plus snow - winter and all-season tires.
• All Season, AW (Any Weather) or AS - all season tires
• The pictogram * (snowflake) means that the rubber is intended for use in winter conditions. If the sidewall of the tire does not have this mark, then this tire is intended for summer use only.
• Aquatred, Aquacontact, Rain, Water, Aqua or pictogram (umbrella) are special rain tires.
• Outside and Inside are asymmetric tires, during installation it is important not to confuse which side is outside and which side is inside. When installed, the Outside lettering should be on the outside of the car, and Inside on the inside.
• Rotation or arrow - This marking on the sidewall of the tire indicates the directional tread pattern of the tire. When installing a tire, you must strictly observe the direction of travel.
• Tubeless is a tubeless tire. In the absence of this inscription, the tire can only be used with a camera. Tube Type - means that this tire must be used only with a tube.

Tire

The size	Load index	Speed ​​index	Pressure, kgf / cm²
205 / 60R16	93	V	2.2
205 / 60R16	92	V	2.2
Replacement
215 / 50R17	91	V	2.2
215 / 50R17	91	W	2.2
225 / 45R18	91	W	2.2
225 / 45R18	91	V	2.2

Disk

The size	Departure	Drilling
6.5Jx16	ET55	5 × 114.3
6Jx16	ET50	5 × 114.3
Replacement
7Jx17	ET60	5 × 114.3
7Jx17	ET60	5 × 114.3
7.5Jx18	ET60	5 × 114.3
7.5Jx18	ET60	5 × 114.3

Mazda6 III GJ

Regardless of the method of production of discs - cast, forged, stamped, there is a standard marking of the size of the discs.

Let's analyze the main parameters 6 GJ - 7.5Jx17 5х114.3 ET 50.

7.5 is the width of the disc in inches. Translated into millimeters, it turns out to be 190.5 mm.

J - the symbol indicates certain design features - the shape of the rims of the disc and serves only for information.

17 - rim rim diameter in inches, which exactly corresponds to the rim diameter of the tire.

5х114.3 - PCD (Pitch Circle Diameter) or drilling in Russian. Here, the number 5 indicates the number of mounting holes for the nuts, and 114.3 is the diameter of the circle (PCD) in millimeters on which they are located.

ET 50 - the overhang of this disc is positive and is 50 mm. The disc protrusion (or ejection) is the distance between the mating plane of the wheel disc and the middle of the wheel rim. The seating plane is the surface that presses the wheel rim against the vehicle's hub.

Additional Information

Additionally, marking 6 GJ, 2012-2015 may contain information:

• DIA D 67.1 - center hole diameter in mm. Ideally, this dimension corresponds to the bore diameter of the hub. On many alloy wheels produced, for greater versatility and applicability to different car brands, the DIA center bore diameter is made large. In this case, the bore diameter of the hub is smaller than the DIA of the disc, and then a special centering seat ring (adapter ring) must be used.
• MAX LOAD - indicates the maximum load on the wheel (indicated in pounds or kilograms).
• SAE, TUV, ISO are analogous to our GOST, a regulatory body. Indicates the standard to which the marking of this wheel conforms.

Tire

Disk

Mazda Mazda6 III GL

Years of issue: from 2015.

Additional Information

• Center Hole Diameter (DIA): 67.1mm;
• Hub fasteners: nut;
• Thread: M12 x 1.5.

Tire

Disk

Rubber and wheel marking carries a lot of necessary information, it is important to be able to understand it. Without this information, you will not be able to choose the right tires for your car, they simply will not fit in size. On the body of the car, special plates are applied with recommendations for the size of tires, we just read them and go to the store for new ones. However, there are not always such plates, and you have to determine the size of the Mazda 6 tires yourself!

Mazda 6 is a passenger car from the Japanese concern of the same name.

Since the presentation of the Mazda 6 model and until the end of 2018, three generations have been released, namely:

• Mazda 6 GG from 2005 to 2007;
• Mazda 6 GH in 2010;
• Restyled version in 2011;
• Third generation in early 2012.

The changes affected not only the exterior, but also the interior, technical characteristics, power unit, transmission.

Sizes of standard wheels for generations of Mazda 6

Mazda 6 (2002 - 2007)
Original (tire)	205/60 R16
Replacement	205/55 R17, 215/55 R18
"Factory" complete set with disks	R16 5x114.3 6J ET50, (6.5J), (ET55)
Disk parameters	PCD: 5x114.3, DIA: 67.1, Nut: 12x1.5
Replacement	R17 5x114.3 7J ET50, ET60, R18 7.5J
Mazda 6 (2008 - 2012)
Factory complete sets	205/60 R16
Replacement	205/55 R17, 215/55 R18
--/--	R16 5x114.3 6J ET50, R17 5x114.3 7J ET50
Mazda 6 (2013 - 2015)
Original	225/55 R17
Replacement	225/45 R19
Mazda 6 (2016 - 2021)
Original	205/60 R16
Replacement	225/55 R17, 215/55 R18
--/--	R16 5x114.3 6J ET50, R18 5x114.3 7.5J ET60

Alternative discs Mazda 6

• Cast: light weight, low pressure on thrust bearings, hub, transmission;
• Stamped: durable, expensive;
• Forged: durable, one third lighter than analogues.

Name	Manufacturer
Light alloy	AITL - 534, 605 Alcar - Hybrid Allante - 184 (HB), 561 Alutec - Freeze, Grip, Ikenu, Monstr, Raptr, Singa, Xplosive Angel - Hornet 601, Rapide 609 Arbet - 1 ATS - Emotion, Streetrally Autec - Hexano, Ionik, Nordic, Polaric, Quantro, Skandic, Wizard, Xenos, Yucon, Zenit Autom - 569, 803 Borbet - CA, F Disla - Evolution, Formula
Stamped	KFZ - 6525, 7503, 7625, 7855, 7856, 8005 ZW - BK5372 (BP) Tech Line - 640 Tomason - TN11 TRW - Z1108 (DGMF) Vossen - CV3, VFS-5 Wheel Master - 0366 WSP Italy - W1704 ZD - 21 ZF - FM039 (BMF)
	Replica - Mazda SSL016 (HS), NS5264 Rial - Arktis Sportmax Racing - 1235 Storm - BK-438 Tech Line - 1603 Lawu - SL-511, YL-245, YL-828 LSW - L-335 Mak - Nitro Marcello - MR-07 PDW - 8052 Racing Wheels - H-126 RC Design - RC-11 Replay - NS38
European brands	Disla Assassin Black Matt, Gunmetal Diamond Dotz Dakar Hamann HA1005 (MB) (BMW) Kapitan Berlingo / Partner 1998-2002 Black Kormetal KM 225 Firebird, KM 250, KM 245 Tornado Kosei RX SUV Replay A101 (GMF), A25 (GMF) Replica legeartis A47 (SF), A513 (BKF), A521 (BKF) Tech Line 311 BD, 503 BD, 526 BD Vianor VR13 (SF), VR16 (BKF), VR29 (GMF), VR32 (SF) WSP Italy T562 Amalfi AU62 Silver, W1006 Cayenne PO06 Chrome, W1050 Philadelphia Antracite Polished, W1052 Corsair GT3 / RS FL.F PO52 Glossy Black

* check prices in stores at the time of purchase.

• Check the wheel balance on a special diagnostic stand in the workshop. If deviations are found, restore the geometry of the structure. It is impossible to "reanimate" the disk on your own due to the lack of the necessary equipment;
• If you find cracks, dents on the rim, contact the service station for prophylaxis, rolling;
• At high, medium speed modes, avoid getting into pits, bumps. The disc is deformed, the tightness is broken, the tire cord is damaged;
• Pay attention to the pressure in the tires, it should not differ from the manufacturer's recommended pressure. In case of deviation, pump up yourself, contact the service station;
• Observe the transition to summer, winter modes. In summer, the tire pressure is 0.15 atm higher, in winter it is lower by the same amount. The parameters are indicated in the vehicle operating instructions;
• Tighten the nuts on the rim with a torque wrench. Excessive tightening tends to break the studs, weak tightening leads to unscrewing. Which will lead to a collision on the road with an oncoming traffic participant.

In sunny weather, cast aluminum wheels are less susceptible to destructive external influences. But in the slush, ice, when the road is strewn with chemicals, the rim lends itself to corrosion. This provokes paint peeling, destruction of the molecular composition, and a decrease in the strength of the structure.

Wash the wheels as soon as they become dirty. Since it is unlikely that it will be possible to clean it with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, service centers.

Systematic polishing helps to get rid of scratches. Pre-clean the wheel from dirt, dry thoroughly, and then treat with a chemical. Wipe with a rag several times.

Store wheels in a suspended position, do not stack on top of each other. Clean from dirt, dry, wrap with cellophane. Some motorists practice applying an aerosol to the surface before conservation.

The average service life of original disks is 180 - 200 thousand km. With moderate driving style, the change interval will increase by one third. The resource of using tires is 70 - 80 thousand km.

What does the installation of disks of freelance sizes on a Mazda 6 car affect?

The size of tires, disks affect the technical characteristics of the machine. The instruction manual contains the recommended and permissible dimensions.

For a driver using the car as a means of transportation, the "factory" (stock) rim sizes are more than enough. In case of tuning, changes in standard characteristics, dynamic performance, "change shoes" the car in non-standard wheel sizes.

The list of characteristics that are changed by installing extra-standard wheel sizes on a Mazda 6 car:

• Controllability;
• Road grip;
• Sharpness, responsiveness of the steering wheel;
• Aquaplaning;
• Comfort;
• Noise level;
• Combined fuel consumption;
• Tread wear.

Decoding of marking of disks, tires on Mazda 6

For example, R19 5 × 114.3 6.5J ET50 (see photo):

• PCD (Pitch Circle Diameter) diameter of the circle of the center of the fixing holes: 71mm;
• Disc radius: 19;
• Number of holes 5;
• Fastener type: М11.0 - stud diameter;
• Thread Measurement (Pitch): 1.25;
• Center hole diameter: 67mm;
• Pressure (front / rear): 2.0 / 2.0 bar.

PCD parameter: distance between centers of opposite holes. Measurement with a ruler without dismantling the wheel. For a five-bolt design, the resulting distance must be multiplied by a factor of 1.05.

Rim Overhang ("ET"): The distance between the point of contact between the disc and the hub and the middle of the rim width. Designation: DEPORT, OFFSET. The offset is positive if the plane does not go beyond the point of contact, otherwise the offset is negative. The further the rim is from the body, the more the offset tends to zero.

• D is the diameter of the central hole, measured in millimeters.
• J, H and subsequent characters alphabetically indicate the markings of the humps on the rim shelf. Symmetrical, asymmetrical and combined.
• The "hum" is the lip on the rim for a tubeless tire. When driving, the "rails" hold the beads of the tire, preventing depressurization.

Numeric characters indicate the release date, month, year.

• TUV is an abbreviation of a supervisory authority for compliance with quality standards.

Maximum wheel load: the unit of measure depends on the country of the manufacturer of the rubber, rim.