The function of the fuse box is to protect against overvoltage and failure of the electrical equipment of the machine. Therefore, when, for example, headlights, a stove, or a gas pump stop working in your car, check the fuses first. Maybe they are the cause of the problem.
Before you buy fuses or any hyundai spare parts, let's determine which of the fuses is responsible for what in the car.
There are three fuse boxes in the Hyundai Accent. Two are in the cabin, and the third is under the hood.
Fuse box in engine compartment. And a list of what each detail is responsible for.
Fuse box in the cabin. It is located below the steering wheel, on the left. To get to it, remove the decorative trim on the dashboard.
The second block is located behind an additional glove compartment in the cabin. There are relays that protect powerful energy consumers in the car.
Relay number and what it is responsible for:
- Responsible for distribution braking force. In the event of a breakdown during braking, the car "leads".
- Responsible for the rear fog lights.
- This is the main relay for the Hyundai Accent. In the image, the relay is disconnected from the connector.
- Follows the headlight bulbs.
- Responsible for the operation of the windshield wiper and washer motor.
- Responsible for the operation of the ABS.
- Responsible for the operation of power windows.
- Responsible for the heating mechanism rear window.
- Responsible for the operation of the steering horn.
- Ensures the operation of turn lamps and light signaling.
Any novice motorist can change the fuse.
- Disconnect the battery first. Open the hood and remove the negative terminal.
- Now open the cover of the mounting block. You can pry it off with a flathead screwdriver or some other hand tool.
- Now you need to check the fuse. Remove it with tweezers or hands and check visually. There is a fusible thread inside the fuse. It may break or burn out. Such a component becomes unusable.
Remember! The new fuse must be the same rating as the one you removed.
- Now check if the problem is fixed by connecting the battery. If so, don't forget to replace the cover.
Onboard network car - direct current, with a rated voltage of 12 V. The electrical equipment is made according to a single-wire circuit: the “negative” conclusions of sources and consumers of electricity are connected to the “mass”: the body and the main units, which act as a second wire. At idle engine switched on consumers are powered by the battery, and after starting the engine - from the generator alternating current with built-in rectifier and electronic voltage regulator. When the generator is running, the battery is charged.
All electrical circuits vehicle (except for the starter power circuit) are protected by fuses installed in the fuse box in the passenger compartment and the relay and fuse box in the engine compartment. Powerful consumers (headlights, cooling fan motor, electric fuel pump, etc.) are connected through relays installed in the relay box in the passenger compartment and the relay and fuse box in the engine compartment.
Hyundai Accent (TagAZ). M RELAY AND FUSE BOXES
The relay and fuse mounting block is located on the left in the engine compartment. The location of the fuses and relays is indicated on the outside of the cover. The relay box in the passenger compartment is located under the instrument panel behind the additional glove box. To replace the relay, open the storage compartment
Mounting block for relays and fuses in the engine compartment:
1 - fuse 100 And the generator circuit; 2 - fuse 50 A complex (circuits of the electric door lock, alarm, brake signals,rear window heatingsound signal, interior lighting lamp, ECU);3 - fuse 30 And the chains head lamps and side light; 4 - fuse 20 A control unit circuit engine; 5 - 30 A fuse for starting the engine and ignition coils.6 - fuse 20 A fan circuit radio ra system engine cooling, 7 - wiring connector,8 - fan relay heater. 9 - relay sound signal, 10 - fuse 10 A interior lamp circuits. 11 - fuse 10 A of the circuit of the head unit of the system sound reproduction.12 - relay 2 condenser heat exchanger fan systems conditioning,13 - clutch relay air conditioning compressor,14 - fog relay socket headlights; 15 - backup fuse socket;16 - fuse 15 A regulator idle move and camshaft position sensor.17 - fuse 10 A circuit of the engine control unit.18 - radiator fan relay of the engine cooling system;19 - 10 A fuse for the air conditioner switching circuit;20 - relay 1 of the fan of the heat exchanger of the condenser of the air conditioning system;21 - 10 A fuse for the engine control unit circuit,22 - 10 A fuse for the air conditioning compressor clutch circuit,23 - fuse 10 A horn circuit;24 - 15 A fuse for the fog lamp circuit.25 - 10 A fuse for the right headlight lamp circuit.26 - 10 A fuse for the left headlight lamp circuit;27 - 10 A fuse for the side light lamp circuit on the starboard side of the vehicle;28 - fuse 10 BUT side light lamp circuits port side car ; 29 - marker lamp relay Sveta; 30 - generator pre-excitation resistor; 31 - starter relay, 32 - fuse 20A fan circuit condenser heat exchanger siems kindlylimitedin, 33 - a 30 A pre-protector for the power window circuit. 34 35 - a socket of the relay of permanently switched on low beam; 36 - relay fuel pump;37 - 30 A fuse for the ABS control unit circuit; 38,39 - diode socket; 40 - 30 A fuse for heater fan circuit
Relay box in the cabin:1 - turnip electronic distribution braking force (EBD); 2 - relay fog light in the rear lights3 - the main relay of the engine management system (for clarity, the mount is disconnected);4 - head light relay;5 - windshield wiper and washer relay;6 - ABS relay; 7 - power windows relay;8 - rear window heating relay,9 - the relay of a sound signaling device;10 - turn signal relay and alarm
We lift the box and remove it from the latches, opening access to the relay.
To access mounting block fuses open protective cover under the instrument panel to the left of the driver's feet. On the inside of the cover is a diagram of the location of the fuses in the block. Replacing relays and fuses is carried out in the same way as described in sec. (cm. " Replacing the relay and fuses of the engine management system", With. 74).
fuse mounting blocktel in the cabin: 1 - 10 A fuse for direction indicator circuit;2 - 10 A fuse for ABS circuits, control lamps in the instrument cluster;3 - 10 A fuse for the instrument cluster circuit;4 - 15 A fuse for the airbag circuit;5 - 10 A fuse for the circuits of the engine control unit, light lamps reversing, automatic transmission control unit;b- 10 A circuit fuse electric drive door locks;7 - 10 A fuse for the alarm circuit;8 - fuse 10 A of the brake signal circuit;
9 - 20 A fuse for the heated rear window circuit.10 - fuse
10 A circuits of the windings of the headlamp relay. power windows, headlight washer, air conditioning condenser heat exchanger fan, engine cooling system radiator fan, fog lights. fog light in rear lights .11 - 20 A fuse for the windshield wiper and washer circuit. 12 - 10 A fuse for the seat heating circuit (option), 13131 134 ..
4.5 Rating 4.50 (2 Votes)
In the Hyundai Accent, as in any other car, fuses are a kind of protection for the electrical equipment of the car. If the wiring is shorted, they can burn out. In this case, it is enough to replace one of the elements of the fuse block, and you can continue to enjoy a comfortable ride.
To eliminate incorrect work cigarette lighter, brake light or dimensions, you need to know the location and number of the fuse responsible for the failed electrical circuit. This car has 2 blocks with protective elements.
Fuse box Hyundai Accent under the hood. 
AT engine compartment block with protective devices and relay is behind battery th. Its cover is fixed with plastic clips. After opening you can see fuse location, and extract desired element. The block has special tweezers for removing burnt parts.
Fuse box in the cabin Hyundai Accent 
In the cabin, the protective elements are located on the dashboard (on the left side of the steering wheel). The block contains fusible links responsible for electrical devices salon, for example, cigarette lighter, signal fuse, door opening lights, etc. To remove the burnt device, just open the plastic cover. FROM inside It has a diagram showing fuse location in the block.
With the above information, you can fix the breakdown of one of the electrical appliances in a car of this brand at no additional cost. Now you will no longer have questions about where to look for the fuse and how to replace it.
DESCRIPTION OF THE DESIGN OF ELECTRONICS AND ELECTRIC EQUIPMENT Hyundai Accent(Hyundai Accent)
The on-board network of the car is direct current, with a rated voltage of 12 V. The electrical equipment is made according to a single-wire circuit: the “negative” conclusions of sources and consumers of electricity are connected to the “ground”: the body and the main units that act as a second wire. When the engine is not running, the switched on consumers are powered by the battery, and after the engine is started, they are powered by an alternator with a built-in rectifier and an electronic voltage regulator. When the generator is running, the battery is charged.
All electrical circuits of the vehicle (except the starter power circuit) are protected by fuses installed in the fuse box in the passenger compartment and the relay and fuse box in the engine compartment. Powerful consumers (headlights, cooling fan motor, electric fuel pump, etc.) are connected through relays installed in the relay box in the passenger compartment and the relay and fuse box in the engine compartment.
MOUNTING BLOCK RELAYS AND FUSES Hyundai Accent (Hyundai Accent)
The relay and fuse mounting block is located on the left in the engine compartment. The location of the fuses and relays is indicated on the outside of the cover. The relay box in the passenger compartment is located under the instrument panel behind the additional glove box. To replace the relay, open the storage compartment
Mounting block for relays and fuses in the engine compartment:
1 - fuse 100 A of the generator circuit; 2 - 50 A integrated fuse (circuits for the electric door lock, alarm, brake signals, rear window heating, horn, interior lighting lamp, ECU); 3 - fuse 30 A of the head and side light lamp circuit; 4 - 20 A fuse for the engine control unit circuit; 5 - 30 A fuse for starting the engine and ignition coils; b - 20 A fuse for the radiator fan circuit of the engine cooling system; 7 - electrical wiring connector; 8 - heater fan relay; 9 - horn relay; 10 - 10 A fuse for interior lighting lamp circuit; 11 - 10 A fuse for the circuit of the head unit of the sound reproduction system; 12 - relay 2 of the fan of the heat exchanger of the condenser of the air conditioning system; 13 - air conditioning compressor clutch relay; 14 - fog lamp relay socket; 15 - reserve fuse socket; 1b - fuse 15 A for the idle speed controller and the camshaft position sensor; 17 - fuse 10 A of the engine control unit circuit; 18 - radiator fan relay of the engine cooling system; 19 - fuse 10 A for the air conditioning circuit; 20 - relay 1 of the fan of the heat exchanger of the condenser of the air conditioning system; 21 - 10 A fuse for the engine control unit circuit; 22 - 10 A fuse for the air conditioning compressor clutch circuit; 23 - fuse 10 A of the horn circuit; 24 - fuse 15 A fog lamp circuit; 25 - fuse 10 A of the circuit of the right head light lamp; 26 - fuse 10 A of the circuit of the left head light lamp; 27 - fuse 10 A of the side light lamp circuit of the starboard side of the car; 28 - fuse 10 A of the side light lamp circuit of the left side of the car; 29 - side light lamp relay; 30 - generator pre-excitation resistor; 31 - starter relay; 32 - fuse 20 A of the fan circuit of the heat exchanger of the condenser of the air conditioning system; 33 - 30 A fuse for the power window circuit; 34 - 30 A fuse for the ABS control unit circuit; 35 - relay socket for constantly on low beam; 36 - fuel pump relay; 37 - 30 A fuse for the ABS control unit circuit; 38.39 - diode socket; 40 - fuse 30 A heater fan circuit
drawer, lift and remove it from the latches, opening access to the relay.
To access the fuse mounting block, open the protective cover under the instrument panel to the left of the driver's feet. On the inside of the cover is a diagram of the location of the fuses in the block. Replacing relays and fuses is carried out in the same way as described in sec. (See "Replacing the relays and fuses of the engine management system", page 74).
IGNITION SWITCH Hyundai Accent
The ignition switch is non-separable. The switch housing is made integral with the steering column - to replace it, it is necessary to replace the column. An immobilizer sensor is installed on the ignition switch.
REMOVING THE CONTACT GROUP OF THE IGNITION SWITCH Hyundai Accent (Hyundai Accent)
Remove the upper and lower steering column covers. To do this, lower the steering column tilt adjustment lever.
Using a Phillips screwdriver, unscrew the three screws securing the lower casing.
We pry off the upper casing with a screwdriver, placing a rag under it to avoid scratching.
Disconnect and remove the upper and lower casings.
The casings are fastened with plastic latches.
Disconnect the wiring harness contact group.
We release the plastic clamp of the ignition switch.
Disconnect the immobilizer wiring harness.
Using a Phillips screwdriver, unscrew the screw securing the immobilizer.
We remove the immobilizer.
Using a Phillips screwdriver, unscrew the screw securing the contact group.
We remove the contact group.
We install the contact group of the ignition switch in the reverse order. When assembling, pay attention to…
... so that the groove of the contact group coincides with the tongue of the ignition switch.
BATTERY Hyundai Accent (Hyundai Accent)
The car is equipped with a low-maintenance lead starter battery with reverse polarity (if the “negative” terminal is facing the left side of the vehicle, then both terminals are located closer to the bulkhead), the nominal voltage of which is 12 V. The nominal capacity at a 20-hour discharge mode is 55 Ah . The battery case is made of translucent plastic. When working with the battery, strictly follow the safety regulations (see “Safety for maintenance and repair”, page 11).
REMOVING THE BATTERY Hyundai Accent (Hyundai Accent)
Using the “10” key, we loosen the fastening of the “negative” wire terminal at the battery terminal and remove the terminal.
GENERATOR REMOVING THE GENERATOR Hyundai Accent (Hyundai Accent)
DESIGN DESCRIPTION
The generator is a three-phase synchronous electric car AC with electromagnetic excitation, with built-in silicon diode rectifier and electronic voltage regulator.
Lifting the cover...
... similarly remove the terminal of the "positive" wire.
With a “12” head with an extension, we unscrew the bolt ...
... and remove the clamping bracket.
The alternator label indicates the current and voltage supplied by the alternator.
The generator rotor is driven by a pulley crankshaft poly V-belt engine.
The stator and generator covers are tightened with four bolts. The rotor shaft rotates in bearings installed in the covers. The bearings are greased at the factory to last the lifetime of the generator. The excitation winding of the generator is located on the rotor. Its conclusions are soldered to two copper slip rings on the rotor shaft. Power is supplied to the excitation winding through carbon brushes. The brush holder is structurally integrated with the voltage regulator.
The generator windings and the rectifier unit are cooled by two impellers located on the rotor. The back of the generator is covered with a plastic casing.
We take out the battery from the engine compartment.
Install the battery in reverse order.
Generator
Disconnect the "negative" wire from the battery terminal.
We remove the alternator drive belt (see "Adjusting the tension and replacing the alternator drive belt", p. 38). Pressing the latch...
... we disconnect the block of wires.
Pressing the latch...
... open the protective cap of the output "B +" of the generator.
Using the “12” head, unscrew the wire fastening nut ...
... and remove it from the output "B +" of the generator.
STARTER. REMOVING THE STARTER Hyundai Accent (Hyundai Accent)
With the “12” head, we unscrew the bolt securing the generator to the adjusting bar ...
…and shoot stretching device generator belt.
We remove the oil filter (see "Changing the oil in the engine and oil filter", With. 31). We unscrew the nut of the bolt of the lower fastening of the generator a few turns. Lifting the generator...
... we remove the bolt from the slot of the body oil pump…
... and remove the generator.
We install the generator in the reverse order and check the tension drive belt(see "Adjusting the tension and replacing the alternator drive belt", page 38).
DESCRIPTION OF THE DESIGN Starter for Hyundai Accent (Hyundai Accent)
On the Hyundai car Accent (Hyundai Accent) installed starter, which is a four-pole, four-brush DC motor with permanent magnet excitation, with planetary gear, roller clutch freewheel and two-winding traction relay.
To steel body starter attached permanent magnets. The body and covers of the starter are tightened with two bolts. The armature shaft rotates in plain bearings. Torque from the armature shaft is transmitted to the drive shaft through a planetary gearbox. A freewheel clutch (overrunning clutch) with a drive gear is installed on the drive shaft. It transmits torque in only one direction: from starter to the engine, disengaging them after starting the engine.
This is necessary to protect the gearbox and starter armature from damage due to excessive speed.
The traction relay is used to engage the drive gear with the ring gear of the flywheel of the crankshaft of the engine and turn on the power to the starter motor, which occurs when the ignition key is turned to the "START" position (in a car with an automatic transmission, the gear selection lever must be in the "P" positions or "N"). After closing the contacts of the traction relay, the retracting winding is turned off.
Disconnect the "negative" wire from the battery terminal.
It is more convenient to remove the starter from a car installed on a viewing ditch or overpass.
Disconnect the wire harness from the starter.
With a “12” head, unscrew the nut ...
... and disconnect the wire tip from the starter output.
With the “14” head, we unscrew the two mounting bolts (the lower bolt also secures the tip of the “mass” wire) ...
…. and remove the starter.
To replace the traction relay ...
... with the “12” key, we unscrew the nut that fastens the wire tip to the output of the traction relay ...
... and remove the tip from the output.
Using a Phillips screwdriver, unscrew the two screws securing ...
… and shoot traction relay starter.
Install pull relay for starter and starter to the vehicle in reverse order.
Hyundai Accent
The car has two headlights. The headlight unit is equipped with headlight, direction indicator and side light lamps. Lamp of the head (dipped and main) light - two-filament, halogen; turn signal lamp - single-filament, with an orange bulb; side light lamp - baseless. The car is equipped with a headlight corrector with an electromechanical drive, which allows you to adjust the direction of the light beam depending on the load of the car. The headlight corrector consists of a regulator on the instrument panel, electric drives installed in the headlights, and connecting wires.
The car can be equipped fog lights. The reversing lights come on when the ignition is on and the reverse gear is engaged. Removal of a lantern, replacement of a lamp of dimensional light and a signal of braking see in section. “Replacing the head and side light bulbs in the headlight, the combined side light and brake light bulb in rear light”, (p. 46). The remaining lamps installed in the rear light are replaced in the same way.
When the brake pedal is depressed, the brake lights are switched on automatically by a switch installed in the pedal assembly bracket. All switches are not subject to repair, in case of failure they are replaced with new ones. The sound signal is fixed on a bracket on the upper cross member of the radiator frame. The signal is activated by a button on the steering wheel. If necessary, you can adjust the sound of the signal by turning the adjusting screw.
REPLACEMENT OF BULBS UNIT HEADLIGHTS Hyundai Accent (Hyundai Accent)
You can change the bulbs without removing the headlights from the car. For clarity, the work is shown on the removed block headlight.
Replacing head and side light bulbs is shown in sec. “Replacing the head and side light bulbs in the headlight, the combined side light and brake light bulb in the rear light”
To replace the turn signal bulb... 
... turn the lamp socket counterclockwise by 45 ° ...
... and take it out of the headlight housing.
By pressing the lamp, turn it counterclockwise until it stops ...
... and remove the lamp from the cartridge.
REMOVING THE HEADLIGHT
Disconnect the "negative" wire from the battery terminal.
Pressing the latch...
... turn signal ...
... disconnect the block of wires from the electric corrector drive.
Disconnect the wires from the lamps ...
... head and side light (see "Replacing the head and side light bulbs in the headlight, the combined side light and brake light bulb in the rear light", p. 46). We turn off the “10” head ...
... two headlight mounting bolts.
Using a Phillips screwdriver, unscrew the latch ...
... and take out the piston top mount front panel.
We remove the headlight from the car.
Install headlight in reverse order. We check and, if necessary, adjust the headlights (see "Adjusting the direction of the headlight beams", p. 44).
REMOVING THE DRIVE OF THE ELECTRIC CORRECTOR OF THE UNIT HEADLIGHT Hyundai Accent (Hyundai Accent)
To remove the electric corrector drive of the left headlight, it is necessary to remove the battery (see "Removing the battery").
We disconnect the block of wires from the electric corrector drive (see "Removing the block headlight"). For clarity, we show the work on the removed block headlight.
Rotate the drive 90° so that its connector moves to the top position.
Unscrew the adjusting screw with a slotted screwdriver ...
... and remove the drive from the hole in the headlight housing.
Headlamp electrocorrector drive
Install the drive in reverse order.
REMOVING THE SIDE TURN SIGNAL, REPLACING THE LAMP Hyundai Accent (Hyundai Accent)
Remove the fender liner from the side of the lamp being replaced. To replace the side turn signal bulb...
We take out the cartridge with the lamp from the pointer housing.
Remove the lamp from the socket.
Install the turn signal bulb in reverse order.
To remove the turn signal by pressing the latch ...
... disconnect the wire block from the indicator cartridge.
By pressing the latch with your finger ...
… push out back pointer outside...
... and remove the pointer from the car.
Install the side turn signal in reverse order.
REMOVING THE REVERSE LAMP SWITCH Hyundai Accent
For clarity, we show the work on removed box gears. To remove the reversing light switch, disconnect the wire block from the switch.
Turn off the switch with the “24” key ...
... and remove it.
The sealing of the switch is not structurally provided. Install the switch in reverse order.
REMOVING THE REAR LICENSE PLATE LIGHT, REPLACING THE LAMP Hyundai Accent (Hyundai Accent)
To remove the headlight...
... and remove the cover.
On the inside of the trunk lid...
... use a Phillips screwdriver to unscrew the three screws securing the trunk lid lining ...
By pulling the lamp along the axis of the cartridge ...
... we disconnect the block of wires from the lamp socket.
... remove the lamp.
Replace the burnt out bulb with a new one.
REMOVING THE INTERIOR LIGHT, REPLACING THE LAMP Hyundai Accent (Hyundai Accent)
... take out the lamp.
Install the lamp in reverse
sequences.
To remove the cover, remove it
diffuser.
Using a Phillips screwdriver, unscrew the two screws securing the lamp to the trunk lid ...
Using a Phillips screwdriver, unscrew the two screws securing the cover housing ...
... carefully pry with a screwdriver ...
... and take out the lantern from the hole in the lid.
We install the lamp in the reverse order. To replace the lamp on the inside of the trunk lid, turn its socket counterclockwise ...
... and remove the ceiling lamp housing from the upholstery of the ceiling.
... and remove the diffuser of the ceiling.
... and remove the cartridge with the lamp from the diffuser body.
By pressing the spring contact of the ceiling ...
Pressing the latch...
... we disconnect the block of wires from the body of the ceiling.
Install the interior light in reverse order.
REMOVING THE PADDLE SWITCHES Hyundai Accent (Hyundai Accent)
We show the work on the example of a combined headlight switch and direction indicators.
Disconnect the "negative" wire from the battery terminal. We remove the upper and lower casings of the steering column (see "Removing the contact group of the ignition switch").
Disconnect the wiring harness from the steering column switch.
Using a Phillips screwdriver, unscrew the two screws securing the steering column switch to the connector ...
... and take out the switch.
Install the steering column switch in reverse order.
The windshield wiper and washer switch is removed in the same way.
REMOVING THE SOUND SIGNAL Hyundai Accent (Hyundai Accent)
Opening the hood, fix it with an emphasis.
Using the “10” wrench, unscrew the nut securing the sound signal plates to the upper cross member of the radiator.
Pressing the pins...
... we disconnect the block of wires from the sound signal. Using the “13” key, we unscrew the nut securing the sound signal to the plates ...
... and remove them.
The sound of the signal is regulated by a screw (shown by an arrow).
Install the sound signal in reverse order.
REMOVING THE WINDSHIELD WIPER GEAR MOTOR Hyundai Accent
Disconnect the "negative" wire from the battery terminal.
We drown the latches of the two plugs of the right windshield lining.
Taking out the plugs...
... and remove the cover.
We are filming protective grille air box.
Disconnect the wiring harness block from the gear motor.
With a “10” head with an extension, we unscrew the four bolts securing the gear motor.
Pulling the gear motor towards us, we release the crank hinge and remove the gear motor.
Using the “13” wrench, unscrew the crank fastening nut, holding it from turning with a screwdriver.
Removing the crank
...and a sealing case.
We install the motor-reducer in the reverse order. To install the shaft of the geared motor in starting position We put the terminal of the "negative" wire on the output of the battery. We connect the block of wires to the gear motor and turn it on with the steering column switch, then turn it off and wait for the motor shaft to stop. Disconnect the wiring harness from the gear motor. In this position of the shaft of the motor-reducer, we set the crank so ...
…as shown in the photo.
Holding the lever through the window in the air intake box from moving ...
... insert the ball pin of the crank into the hole of the lever to a fixed position.
Further installation of the windshield wiper motor-reducer is carried out in the reverse order.
REMOVING THE WINDSHIELD WASHER ELECTRIC PUMP on Hyundai Accent (Hyundai Accent)
Removing the right fender front wheel(see "Removing the front fender liner", p. 142). Pressing the latch...
... disconnect the wiring harness from the windshield washer pump.
Remove the fluid supply hose to the windshield injectors from the electric pump nozzle.
We remove the electric pump from the tank.
Install the windshield washer pump in reverse order.
REMOVING THE INSTRUMENT COMBINATION, REPLACING THE BULBS Hyundai Accent (Hyundai Accent)
Disconnect the "negative" wire from the battery terminal.
Install steering column to the lowest position.
Using a Phillips screwdriver, unscrew the two fastening screws ...
... and remove the instrument cluster trim.
Using the same tool, we unscrew the four screws securing the instrument cluster ...
...and move it towards us.
In this case, the speedometer drive cable shank will come out of the instrument cluster hole.
Pressing the latch...
... disconnect the wiring harness from the instrument cluster connector.
Disconnect the rest of the wires in the same way...
... and remove the instrument cluster.
The wire blocks are different, so it is impossible to mix them up when connecting.
To replace the illumination lamp or indicator lamp in the instrument cluster...
... turn the lamp socket counterclockwise ...
... and remove it together with the lamp from the socket in circuit board instrument clusters.
We take out the lamp from the socket.
Green light filters are installed on the flasks of the illumination lamps of the instrument cluster.
When replacing the lamp with a new one, we rearrange the light filter. Install the lamp in reverse order. Pilot lamps replace with cartridges. Install the instrument cluster in reverse order.
Wherein…
... the tail of the speedometer drive cable must enter the corresponding hole in the instrument cluster.
REMOVING THE ELECTRIC HEATER FAN Hyundai Accent (Hyundai Accent)
Disconnect the "negative" wire from the battery terminal.
We open glove box and remove the latches of its limiters (see "Removing the glove box").
Using a Phillips screwdriver, unscrew the four fastening screws ...
... and remove the glove box along with the mounting plate.
We take out the wiring harness of the fan motor from the clamp ...
... and disconnect the block.
Using a Phillips screwdriver, unscrew the three screws securing the fan motor cover to the fan housing ...
... and take out the fan impeller assembly with the electric motor and cover.
Before installing the heater electric fan, clean the cavity of the guide casing from dirt.
Install the heater fan in reverse order.
REPLACEMENT OF THE RESISTOR OF THE HEATER FAN Hyundai Accent (Hyundai Accent)
Disconnect the "negative" wire from the battery terminal.
We remove the glove box together with the mounting plate (see "Removing the heater electric fan").
Disconnect the wiring harness block (A) from the heater fan resistor and unscrew the two self-tapping screws (B) securing the resistor. We remove the resistor.
Heater fan resistor
Install the resistor in reverse order.
On Hyundai Solaris cars of the first generation 2010, 2011, 2012, 2013 and 2014, it is installed - 2 distribution blocks with fuses and relays.Location of all blocks in the car
Consider the decoding of block diagrams in detail. The designations indicate what each of them is responsible for.
1. Fuse box under the hood
Fuse | Terminal | Current (A) | Purpose |
Fuel pump |
|||
Sound signal |
|||
Switching unit: emergency gang, power windows, central heating, fuses - F23-F25, F31, F32 |
|||
Heating control unit |
|||
Engine control unit - relay 1. Fuse F25 |
|||
ACC - relay. Ignition lock, body electrical control module, automatic transmission lock control module, start-stop button control unit. IG2 - relay |
|||
Ignition switch, body electrical control module, automatic transmission lock control module, start-stop button control unit |
|||
Air conditioner |
|||
Engine control module. Gearbox control module. Fuel pump - relay. Oil control valve |
|||
Engine control module. Camshaft sensor. oxygen sensor. Immobilizer. Air conditioning - relay. Fan - relay low speed and relay high speed. Solenoid valve |
|||
Gearbox control unit. Automatic transmission sensor. Dashboard. Combined rear lights. |
|||
| Relay |
|
| Location | Designation |
| Reserve | |
| Horn relay | |
| A/C relay | |
| Ignition Interlock Switch Relay | |
| Fan relay ( low speed) | |
| Fan relay ( high speed) | |
| Diagnostic socket relay | |
| Ignition Switch Relay | |
| Ignition lock relay, body electrical control module, automatic transmission lock control module, engine start and stop button control unit | |
| Alarm relay emergency braking | |
| Relay electronic block engine control | |
| Fuel pump relay | |
| Reserve | |
| Cooling Radiator Fan Relay | |
1.2 Main multi fuse with jumpers
The multifuse is used to optimize the layout of the engine compartment.
2. Fuse box in the cabin, dashboard
Fuse | Terminal | Current (A) | Purpose |
Heated windshield |
|||
Socket 12V |
|||
cigarette lighter |
|||
Ignition lock - audio system, body electrical control module, automatic transmission lock control module, system control unit electronic key |
|||
Airbag Deactivation Indicator - Front |
|||
Airbags, SRS control module |
|||
Emergency light signaling |
|||
Rear window wiper - engine Multifunction switch |
|||
Fog lights (rear) |
|||
Fog lights (front) |
|||
Relay for saving battery charge (automatic protective shutdown) |
|||
Stop lights |
|||
instrument cluster |
|||
Security Control Module |
|||
ABS hydroelectronic module |
|||
Rear running lights(switch) |
|||
Control Module Body Electrical Control Module, Automatic Transmission Lock Control Module, Smart Key System Control Module |
|||
Headlight - left |
|||
DAY TIME RUNNING LIGHT | Daytime Running Lights |
||
Hazard switch |
|||
Control module body electrical control module, automatic transmission lock control module, electronic key control unit |
|||
Control Module Body Electrical Control Module, Automatic Transmission Lock Control Module, Electronic Key Control Module, Engine Start/Stop Button Switch |
|||
Speed sensor Range sensor automatic box gears. Pulse generator |
|||
Ignition coil 1-4, capacitor |
|||
Power windows. Luke |
|||
windshield wiper |
|||
Central locking - control unit |
|||
Power windows - lock |
|||
Heated front seats |
|||
Interior lighting. Air conditioner |
|||
Audio system |
|||
Headlight and lantern on the port side. License plate lighting |
|||
Headlight and lantern on starboard side. Illumination of switches, switches in the cabin, selector lever. Instrument cluster, power and switch buttons |
|||
Starter - relay. Anti-theft alarm |
|||
Headlight - right |
|||
Power Window Control Module - LH Rear Switch |
|||
Power Window Control Module - Right Rear Switch |
Save useful content!
