Car alarm Starline b9 is designed to provide a set of measures to protect the car. It not only protects the car from theft by robbers, but also allows the driver to be sure that everything will be in order with it. That is why he does not worry about her safety, which has a positive effect on his emotional state.

System Features

Under the control of the alarm there are several security zones:

• car trunk, doors, hood for opening - push-button limit switches;
• body, wheels, windows for mechanical effects - a two-level shock sensor;
• engine from starting - Starline DDR digital radio relays, conventional relays;
• ignition from switching on - there is a voltage control sensor;
• Parking brake against disengagement - push-button limit switch.

The security of the signaling is provided by the original dialogue control code, a special coding algorithm "friend or foe" is used, which protects against selection and interception. To eliminate the possibility of a power reset, the system remembers the initial state when the power is turned off and returns back when it is restored. When the external power is off, the engine remains blocked if the system was in the armed state. Alarm cycles from sensors are limited. Interruption of alarm signals becomes possible even without disarming the machine.

Protective and anti-theft functions

The alarm also has a number of useful service functions: starting the engine from the remote control, programmable activation of the motor depending on time, temperature. Consider the most important features devices:

• if the sensors are triggered in armed mode, alarms are activated. In this case, a signal is sent to the remote control with alarm notification feedback;
• when the immobilizer mode is on, the engine will be blocked automatically after the ignition is turned off after 30 seconds, regardless of the state of the security mode;
• when you turn on the anti-robbery mode, depending on the programming, the following occurs: automatic locking door locks, blocking the engine, for the initial 30 seconds in a pulsed mode, then continuously;
• for turbocharged cars, a turbo timer mode is provided, it keeps the car engine running after the ignition is turned off for the time required before the turbine stops. If the car is armed during its operation, the system will turn off the ignition inputs and the shock sensor for the duration of the operation, the engine will not block. The system will fully arm the car after working out the mode;
• the ability to program disarming without a key fob. Or with a set personal code, or not (programmable functions). In both cases, the service button is used to disarm the car;
• the ability to program an individual emergency shutdown code up to three significant digits;
• if the engine blocking is enabled (the system is armed), then it will remain blocked even if the alarm central unit is detected and disconnected from the alarm connectors.

Service functions

The car security system has a number of service functions. Among them are: security mode with the engine not turned off, silent protection, silent activation of functions, panic mode, work with the GSM / GPS module, car search. The alarm system performs automatic control of the sensors, bypasses the fault zones and reports about it. The device has the functions of engine activation: from the remote control - remote start, automatic switch on by timer every 2, 3, 4, 24 hours, by temperature, alarm clock. There are settings for the features of working with automatic and manual box gear, different types engines (gasoline, diesel).

Contents of delivery

Included in delivery burglar alarm includes:

• complete installation kit including central control unit, antenna with transceiver module, driver call button and temperature sensor for salon, a set of cables;
• two-level shock sensor, distinguishes between weak and strong shocks, while the alarm responds with a short series of sound signals or turns on a full alarm;
• temperature sensor for the engine;
• remote controls:

1) With liquid crystal display and feedback.

2) Without feedback, three-button key fob without display.

• the LED installed in the car indicates the operating modes;
• remote emergency switch - this is a button that should be installed in the car in such a way that sufficient secrecy of its location and ease of use are ensured;
• complete documentation for installation and management.

Remote controls

The security alarm set includes two key fobs: main and auxiliary. The main key fob resembles a small transmitter with three control buttons and an LCD display screen. The keychain has feedback. The key fob indicator reflects the current state of the security system, intuitively clear pictograms. The security system is programmed from the key fob. In addition to the main purpose, the key fob displays the current time, and some Extra options: car temperature, engine temperature. The key fob is powered by a 1.5-volt AAA battery, depending on the intensity of use, it lasts from six months to 9 months.

The second key fob has no feedback. The key fob buttons have the same set of functions as the main one. There is an LED indication of its operation. The key fob does not support the encoding algorithm, so it is advisable to use the main option. The key fob is powered by a 3-volt battery, depending on the intensity of use, it lasts for 9-12 months. If several people use the car, it is advisable to purchase additional key fobs with feedback.

Buttons on the key fob

The purpose of the buttons on the key fobs is the same:

• button 1 - arming, locking locks, control of the shock sensor by levels;
• button 2 - disarming, unlocking locks, interrupting alarms. Also responsible for turning off the "anti-robbery" mode, managing an additional sensor;
• button 3 - switching on the “temperature indication” mode and detecting the alarm status, activating an additional channel, activating the cursor selection of functions.

Benefits of signaling

Among automobile security systems with feedback, the presented device occupies a worthy place. The alarm has the ability to connect additional devices(tilt, pressure sensors, microwave, ultrasonic), which significantly expands the scope of its application. The device circuit is built on a relay type. This allows you to freely install the alarm anywhere in the car, which increases security. In this case, blocking is carried out by means of the Starline DRRTM radio relay.

There are 7 control relays in the main unit. They control the starter, ignition, electric door locks, sound and light, and other equipment. Another feature of the alarm system is the ability to control it using GSM channels in their coverage area. That is, it is possible to control the alarm from a regular cell phone. In order to use this feature, you need to install an additional Starline Messenger GSM-module. The module has three auxiliary equipment control inputs. When sensors or alarms are triggered, an SMS or a call is sent to the phone.

The alarm system is designed to be installed on a vehicle with on-board voltage 12 V. It is best to install the central unit in a accessible place. Usually placed under dashboard, shorter cable lengths and appropriate routing.

Antenna with transmitter module on Windshield. This will ensure the maximum range of the transmitters. The cabin temperature meter is located in the same module, so the location of the module should be taken into account. In this case, it is desirable to avoid heating from car stove, direct sunlight and other heat sources.

The shock sensor is also recommended to be located in the passenger compartment, it needs periodic access for timely adjustment. The sensor must be rigidly fixed to the body. The temperature sensor of the engine is fixed on the engine housing or metal parts adjacent to it. The correct temperature value is important for automatic engine start.

The Valet service button must be installed in a hidden but accessible place. It may be required in emergency cases, so it is advisable not to place it in places where there is no quick access. When submitting a car to a service station for repair, it is recommended to turn on the Valet mode. In this case, some of the alarm functions are disabled, so there is no need to transfer the key fobs of the security system to the repairmen.

Not really

In our article " Starline car alarm B9 — detailed description of all functions "we will tell you about the car star line alarm b9 and about its differences from previously available models. Starline b9 is a brand new 12V alarm designed for the car. It has the function of starting the motor and has two-way communication. The set comes with a new unique keychain. Two-way communication is established with an informative LCD display. The starline b9 car alarm is armed with a new unusual dynamic radio control code StarLine ProPlusTM, which is protected from hacking.

The code uses a dialog method for determining the “own” key fob and distributes commands for turning on and off different modes protection. The alarm package includes: a central unit, 2 key fobs (one is interconnected with the LCD and one without two-way communication), a two-level shock sensor, a Valet service button, a transceiver, an LED, a hood button. Keyfobs use a uniform dialogue code. The Starline b9 car alarm supports the reception of engine blocking by digital radio relays. StarLine DRRTM is used as a digital radio relay. Especially for a hidden installation, everything is done quite compactly. Thus, an equivalent cryptographic resistance of the main and additional key fob is provided. As a result of using the new transceiver, the data transfer rate increased, and this affected the reduction in command execution time. Time is now spent up to 1.3 - 1.5 seconds. All texts are Russified.

Starline b9 has a number of innovations regarding multifunctional execution. Among them there are: an improved interface for monitoring the operation and starting control of any motor; independent indication of engine and passenger compartment temperatures; automatic start of the motor by time; when the security mode is turned off, a two-step unlocking of the motor; programmable interface for connecting security sensors (shock sensor, tilt sensor, pressure sensor, microwave sensor, ultrasonic sensor, etc.); selection of algorithms for activating motor blocking outputs; independent indication of sensors; 4 additional control channels; a good method of programming a function on the keyfob LCD indicator with feedback.

The main differences from previous models:

If you associate with the A9 and A8 models, which at one time became very popular, the Starline b9 alarm system is also equipped with a remote control that has a reverse connection. So what is the advantage of this keychain? Keyfob feature is the presence of an LCD display with 44 independent icons on it. This highest score. Among systems with a reverse connection, Starline b9 occupies a leading position. At the moment of receiving the reverse signal from the vehicle, the light indication turns on, which confirms the execution of the command. If the signals are accompanied by a vibration and sound notification on the key fob with the monitor backlight turned on, then this indicates an alarming situation.

In this way, with any impact on the car, the motorist will be notified just in time. Car alarm key fobs of the "b" series are very comfortable to use. Convenience is achieved through the use of the "cursor" method of selecting the command mode. With its help, the alarm management process takes place. The owner of such an alarm now does not need to remember a huge number of button compositions that needed to be dialed to execute various commands.

Another difference between the latest alarm system and previous models is the presence of StarLine NetTM interfaces in the design. With their help, the installation of alarms is greatly facilitated. Together with the Starline b9 alarm, you can use various additional devices for various purposes. And this makes it possible to use:

1. method of blocking the motor with the introduction of digital relays. This makes it possible for a hidden alarm installation;

2. a method for transmitting control signals using GSM channels in the coverage area;

3. A method for tracking the location of a car using GSM satellite communication channels.

The central unit contains 7 relays. With the help of these relays, the implementation of the starter control, ignition control, door lock control, parking light control, etc. is done. The body of the central unit has a reduced size. And at the same time, it has a higher functionality. All this helps to covertly install it in the car. Specifically, the introduction of the latest software developments, the use of electrical components from the best global manufacturers and helps to ensure smooth operation of the device StarLine Twage b9. The presence of a certificate only confirms compliance StarLine devices Twage b9 Russian and international standards.

An additional keychain included in the alarm set is waterproof and ergonomic. It contains a three-volt lithium cell. It is from him that the keychain is powered. His work is designed for a period of more than 1.5 years. The key fob buttons have a special composition that shines in the dark. Specifically, the increased brightness of the LED indicator makes the key fob more comfortable to use. The command compositions on both key fobs are 100% similar. This is done for ease of management.

Car alarm StarLine Twage b9 is widely used on the territory of the Russian Federation, it fully complies with the requirements of the regulations of the Russian Federation. The service life is 5 years, provided that the installation and operation is carried out in accordance with the instructions for the car alarm

Thank you for choosing StarLine car alarm with two-way communication and remote engine start. Its appearance was made possible thanks to the collective creativity of Russian development engineers, American specialists in the field of microelectronics and Taiwanese manufacturers of high-tech automotive security systems. In order for the car alarm to be able to most effectively carry out its security and service functions, we recommend entrusting its installation on the car to professional installers. We hope that the system will not deceive your expectations, will give you confidence in the safety of your car and significantly increase its comfort due to various service functions. Country of manufacture: Taiwan Revision No. 1 July 2009 ATTENTION! Mandatory safety precautions when using the engine start function. It must be remembered that the car is a means of increased danger. Section 12.8. rules of the road states: “The driver may leave his place or leave vehicle if they have taken the necessary measures to prevent the spontaneous movement of the vehicle or its use in the absence of the driver. Before operating the StarLine B9 car alarm, carefully read the measures for the safe use of the remote or automatic engine start function described below. 1. Always park your vehicle in an open, well-ventilated area. 2. Always park your car on parking brake, which must be in good condition and exclude the possibility of movement of the car. 3. When leaving the vehicle, be sure to set the control lever automatic transmission in the “PARK” position and the manual transmission shift lever in the neutral position. 4. If your vehicle has a manual transmission, be sure to follow the “programmed neutral” engine start preparation procedure before enabling the remote or automatic engine start function. 5. Never start the car engine in the absence of the driver, if someone is in front of the car or behind it. 2 Operating Instructions 6. Never pass car alarm control fobs to children, as well as to other persons without their prior knowledge of this instruction. 7. On cars with a manual transmission, it is not recommended to start the engine remotely or automatically if the car is out of sight and the car alarm user is not able to control the engine start process. 8. Before turning on the remote or automatic engine start function, you must: - make sure that the car is in good condition; - make sure you have enough fuel, oil, coolant, etc.; - set the operating parameters of the interior heater (air conditioner), glass heating and other accessories to the required levels; - set the interior blower controller to air circulation, which will allow more efficient heating or cooling of the air in the car. 3 Contents Specifications of the alarm .............................................................. .......... 5 Components included in the alarm kit .................................. ...................... 6 List of security and service functions of the alarm system .............................. 8 Alarm control fobs .................................................................. .................... 10 Function of the key fob buttons .............................. ................................................. 12 Setting the keyfob functions............................................... .................................................. 16 Turning on / off the alarm modes using the cursor method ..... ................................................. .... 18 Alarm management Arming .............................................................. .............................. 20 Disarming .......... ................................................. .................. 28 Self-diagnosis gnosis................................................................. ............................... 33 Burglar alarm functions .......................... ............................................. 35 Anti-theft alarm functions.. ................................................. ...... 38 Alarm service functions .......................................... ........................... 46 Starting the engine .................. ................................................. ......................................... 54 Preparing to start the engine on vehicles with manual transmission ................................... 56 Remote engine start .............................................. ................................................. 60 Automatic engine starts ..................... ................................................. .......... 62 Personal emergency shutdown code .......................................... .................................. 65 Programming the security and service functions of the alarm system .............. 66 Summary table of commands executed by the remote control .............. ................................................... 69 Keyfob Batteries and Replacement .................................. ................................................. 72 Warranty ............................................................... .............................. 73 4 Operating Instructions Specifications RF control signal frequency range .................. from 433.075 up to 434.79 MHz Number of channels .............................................. .................... 8 pcs. Key fob action in pager mode .................. 2000 m* Maximum range of additional key fob .................. 15 m* Shock sensor type. ................................................. .......... piezoelectric Operating temperature ..................................... .................... from -40 to +85 °С DC supply voltage .............................. .................................. 9-18V Current consumed by the alarm in armed mode ........ .............. less than 15mA Maximum allowable current at the outputs: siren connection circuits .............................. ............................................... 2A connection circuits direction indicators .......................................... 2x 7.5A control circuits for electric door locks .... .................................. 20A ignition switch circuit .............................. ............................................... 25/30A circuit enabling ACC .................................................................. ......................... 25/30A c starter enable circuit ............................................................... ......................... 25/30A engine interlock circuit ............................... ................................................. 25/30A circuits for additional control channels. .............................................. 300 mA Keyfob power supply with feedback..... .... 1.5V (1 x AAA battery) Power supply for the optional keyfob.......3V (1 x CR2450 battery) * The range of the keyfob and pager may be reduced depending on the location of the transceiver, vehicle location user, radio frequency interference, weather conditions, car battery voltage and key fob battery voltage. StarLine car alarms are approved for use on the territory of the Russian Federation and meet all requirements normative documents RF. The service life of StarLine car alarms, set by the manufacturer, is 5 years, provided that they are installed and operated in strict accordance with the installation and operation instructions. 5 Components included in the alarm kit 1, 2 - instructions for installation and operation; 3 - keychain remote control with feedback and liquid crystal (LCD) display; 4 - battery for keychain with LCD display; 5 - remote control key fob with feedback without display; 6 - central processing unit; 7 - transceiver module with antenna; 8 - two-level shock sensor; 9 - double-sided adhesive tape for attaching the transceiver; 10 - case for key fob with LCD display; 11 - transceiver cable; 12 - shock sensor cable; 13 - hood button; 14 - service button; 15 - temperature sensor; 16 - main cable with 18-pin connector; 17 - power cable for power supply and engine start circuits; 18 - central locking cable with 6-pin connector; 19 - LED indicator; 6 Operating Instructions 7 Security and service functions of the alarm Protected areas of the car and methods of their protection Engine - from starting (conventional relays / StarLine DRR digital radio relays) Doors, hood, trunk - from opening (push-button switches) Parking brake - from turning off (push-button switch ) Body, wheels, windows - from shocks and impacts (two-level shock sensor) Ignition - from switching on (voltage control input at the ignition switch) Alarm security Original dialog control code, protected from selection and interception by a special coding algorithm "friend or foe" state when the power is turned off and return to the same state when the power is restored Limiting the number of alarm cycles from sensors Interrupting alarms without disarming Protective and anti-theft alarm functions Turning on alarms when sensors are triggered in armed mode Immobilizer mode Turbo timer mode Anti-theft mode Programmable 2-step deactivation of engine blocking Programmable personal emergency shutdown code Engine blocking and its preservation when the alarm is dismantled Self-diagnosis and indication of operating modes key fob display Indication of the reasons for the alarm triggering for 9 security zones Indication of a faulty zone when the armed mode is turned on Indication of the fact that the alarm is triggered by sound signals LED indication operation of the limit switches 8 Operating Instructions Alarm service functions Silent armed mode Armed mode with the engine running Silent arming / disarming Arming / disarming without a key fob Bypassing the door zone for the delay time when the interior light goes out Automatic return to armed mode in case of accidental shutdown Remote deactivation sensors by levels in armed mode Remote control central lock Control of the central lock from the ignition lock Two-step unlocking of the door locks Two-pulse unlocking of the door locks Possibility of implementing the "comfort" function 4 additional control channels Control of the car interior lighting Panic mode Car search mode Service mode Call from the car mode Protection against accidental pressing of the remote control buttons Sound and vibration modes of operation key fob with feedback Separate indication of temperature in the passenger compartment and under the hood of the car Power saving mode key fob with liquid crystal display Remote programming of new and deletion of lost key fobs Remote programming of alarm modes and functions Quick reset of programmable functions to factory settings Ability to work with GSM modules StarLine Space and StarLine Messenger Indication current time, alarm clock, timer Engine start functions Remote start / stop the engine Remote extension of the running engine Automatic engine start by temperature, alarm clock, timer every 2, 3, 4 hours or 24 hours (daily timer) Engine type selection: gasoline / diesel Transmission type selection: automatic / manual voltage of the onboard network Automatic protection against starter overwinding when starting the engine Indication of the operating time of the running engine on the keyfob display 9 Alarm control keyfobs The alarm performs its functions either automatically or by keyfob signals when the buttons are pressed. Some of the provided functions and some parameters of the alarm operation can be changed by programming. The alarm system is equipped with a 3-button remote control with feedback and an LCD display and a 2-button remote control with feedback without an LCD display. The dynamic keyfob control code is protected from selection and interception. When the alarm system executes commands transmitted from any remote control, changes the parameters and modes of operation of the alarm system and triggers an alarm, information about the state of the security system is transmitted to remote controls with LCD displays. At the same time, the current state of the alarm is displayed on the remote control screens, sound and vibration signals are turned on, and the backlight is on. The key fob with an LCD display uses an original cursor method for selecting some control commands, in which different commands have their own icon displayed on the key fob indicator. In addition, the remote control LCD displays information about the current time, alarm clock, engine temperature and inside the car. Button 1 Button 2 Button 3 Button 1 Button 2 Key fob with LCD display and feedback. 10 Keychain with feedback, no display. Operating Instructions Additional recommendations for using keyfobs The main keyfob for controlling your alarm system is a keyfob with feedback and a liquid crystal indicator that has an original interactive control code protected by a special “friend or foe” coding algorithm. It is this algorithm that is guaranteed to prevent attempts to intercept the key fob code and then use it to disarm the alarm. The 2-button keyfob with feedback without a display uses the same control dialogue code as the main keyfob with an LCD display. The functions of a pager in a key fob without a display are not implemented and it is intended only to control the alarm security mode. In order to make the most of the functionality provided by the security system, we recommend using a key fob with feedback and an LCD display as the main control tool. If the car is used by two or more owners, we recommend purchasing required amount key fobs with LCD displays. A 2-button key fob, despite its high security, we recommend using as an additional one, if it is not possible to work with the main key fob with an LCD display. 11 Keyfob buttons assignment with feedback and LCD display Button 1 Arming mode with sound confirmation (single press) Arming mode without sound confirmation (consecutive pressing) Disabling / enabling the shock sensor by levels (double pressing) Locking door locks with the ignition on (single press) Button 2 Disarm with sound confirmation (single press) Disable armed mode without sound confirmation (successive press) Disable / enable additional sensor by levels (double press) Unlock door locks with the ignition on (single press) Disable anti-robbery mode (two single clicks) Interruption of alarms (single click) Button 3 Status of the alarm and temperature in the car interior (single click) Activation of the "search" mode and control of the engine temperature (double click) Activation of additional channel No. 3 (consecutive click or) Activation of the cursor selection of the following functions: automatic start by alarm, automatic start by timer, automatic start by temperature, mode after-sales service , turbo timer mode, immobilizer mode, automatic arming mode (long press) Activation of the current time setting mode, alarm indications, power saving mode, vibrating alert mode (long press) Buttons 1 and 2 in sequence Activation of the silent arming mode with turning off the sound confirmation signals Buttons 1 and 3 in sequence Starting the engine or prolonging the operation of an already running engine Button 2, then button 1 Activating the armed mode with the engine running (single presses) Buttons 2 and 3 in sequence Stopping the engine 12 Operating Instructions Buttons 3 and 1 in sequence Activating additional channel No. 2 in sequence Activation of additional channel No. 2 Buttons 1 + 2 simultaneously Activation of the "panic" mode (long press with the ignition off) Activation of the anti-robbery mode (long press with the ignition on) Button 1 + 3 simultaneously Activation of the lock of the key fob buttons (single 2nd press) Buttons 2 + 3 at the same time Switching off the blocking of the remote control buttons (single pressing) Duration of pressing the remote control buttons In order for the alarm to adequately respond to control signals given from the remote control, the duration of pressing the remote control buttons is extremely important. In the further description of the alarm operation algorithms in the text, the following definitions of the duration of pressing the buttons of the control fobs will be used: Short button press - one press of any button lasting less than 0.5 seconds. Long button press - press and hold the key fob button until a melodic sound signal appears. Double button press - two button presses within 0.5 seconds. Sequential pressing of buttons - two pressings of one or different buttons. The first press should be long, the second press - short. Assignment of additional key fob buttons without display Button 1 Arming with sound confirmation (single press) Button 2 Disarming with sound confirmation (single pressing) Disabling anti-robbery mode 13 Key fob LCD display Indication of alarm operation modes. Auto start mode by alarm (on/off) Auto start mode by timer (on/off) Auto start mode by temperature (on/off) VALET service mode (on/off) Turbo timer mode (on/off) Auto arming mode (on/off) off) Immobilizer mode (on/off) Key fob button blocking enabled Emergency pin-code off mode enabled Manual transmission mode enabled open Ignition on Doors, hood, trunk open Parking brake not applied / Pressed foot brake Engine is running Anti-theft mode is on The remote control battery needs to be replaced Engine temperature StarLine Space or StarLine Messenger module is connected Alarm clock is on Timer is on DAT 1 Bypass of the 1st level of the shock sensor DAT 2 Bypass of the 1st level of the additional sensor DAT 1 DAT 2 Bypass of both levels of the shock sensor Bypass of both levels of the additional sensor SH-1 The 1st level of the shock sensor SH-2 was triggered The 1st level of the additional sensor SH-1 was triggered The 2nd level of the shock sensor SH-2 was triggered The 2nd level of the additional sensor SA-2 was triggered 1 was triggered -level additional sensor 15 Setting the key fob functions The key fob allows you to set the following modes and parameters: l current time l alarm time l countdown timer time l enable or disable the alarm l enable or disable the countdown timer 1 Press and hold button 3 (clock setting current time) KEY FOB l l l l hold button 3 until: 1 melodic signal 1 short 2 short beeps the clock icon blinks: button 1 -increases the readings button 2 -decreases the readings press the button 3 2 Short (setting the minutes of the current time) KEY FOB the minutes icon blinks: button 1 -increases the readings button 2 -decreases the readings press the button 3 3 Short ( alarm clock setting) KEYFOB the alarm clock icon flashes: button 1 -increases the readings button 2 -decreases the readings press button 3 5 Briefly (on/off the alarm clock) KEYFOB the alarm clock icon flashes: button 1 - turns on the mode (ON) button 2 - turns off the mode (OFF) press button 3 (setting the timer clock) 6 Short KEYFOB the icon of the clock timer flashes: button 1 - increase the readings button 2 - decrease the readings press the button 3 7 Briefly (setting the minutes of the timer) button 1 - increases the readings button 2 - decreases the readings press the button 3 (on/off the timer) 8 Short KEY FOB the timer icon flashes: button 1 - (ON) button 2 - (OFF) also some special functions are enabled using the programming mode. To enter this mode and execute desired settings follow the steps below 1 Press and hold button 3 until two beeps sound (first long, then short) button 3, move the cursor to the desired icon 3a To turn on the mode, press the button on the key fob 1 KEY FOB CAR l 18 dimensions will flash 1 time will sound sequentially: 2 short and 1 melodious signal l the icon of the selected function will be displayed on the screen l Operating instructions 3b To turn off mode, press the 2 CAR button on the key fob l the dimensions will flash 2 times KEY FOB l will sound sequentially: 2 short beeps 1 melody signal l the icon of the selected function will disappear on the screen List of programmable modes and functions Auto start mode by alarm clock. One of the types of automatic engine start. Allows you to start the engine at the time programmed on the alarm clock. Timer autostart mode. One of the types of automatic engine start. Allows you to periodically start the engine every 2, 3, 4 or 24 hours, depending on the selection. Auto start mode by temperature. One of the types of automatic engine start. Allows you to set the temperature threshold. If the engine temperature drops below the set threshold, the engine will start automatically to warm up. Service mode. The mode is designed to temporarily disable the security and anti-theft functions of the alarm if it is necessary to transfer the car for service or repair. Turbotimer. The mode is designed for cars with turbocharging and allows you to keep the engine running after the ignition is turned off for some time, necessary for cooling the turbine. Automatic activation of protection. In this mode, the protection is automatically activated after the ignition is turned off, 10 seconds after all doors are closed. immobilizer mode. In this mode, the engine is automatically blocked 30 seconds after the ignition is turned off. For more information about the operation of these modes, see the relevant sections of the manual. 19 Arming with audible confirmation signals Before arming, make sure that the ignition is off, the parking brake is on, and the doors, hood and trunk are securely closed. 1 Press the 1 CAR button on the keyfob l the LED indicator will flash l one beep will sound l the dimensions will flash once l the door locks will close (if the locks are connected to the alarm) KEY FOB l a short beep will sound l the icons corresponding to the armed mode will appear on the screen If the doors , hood, trunk turn out to be poorly closed, and the parking brake is not tightened or the foot brake is pressed, and one of the push-button switches of the doors, hood, trunk, brake is faulty, the alarm will warn about this with 4 sound signals and 4 flashes of dimensions (see the section “Self-diagnosis when the security mode is turned on”). 20 Operating Instructions Arming without sound confirmation signals Before arming, make sure that the ignition is off, the parking brake is on, and the doors, hood and trunk are securely closed. 1 Double-click button 1 on the key fob (First press is long, second press is short) CAR l LED indicator will start flashing l dimensions will flash once l door locks will close (if the locks are connected to the alarm) KEY FOB l a short signal will sound l icons corresponding to armed mode If the doors, hood, trunk turn out to be poorly closed, and the parking brake is not tightened or the foot brake is pressed, and one of the push-button switches of the doors, hood, trunk, brake is faulty, then the alarm system will warn about this with 4 sound signals and 4 flashes of dimensions (see paragraph “Self-diagnostics when arming”). 21 Silent armed mode In silent armed mode, there are no vehicle sounds when any of the sensors are triggered. 1 Press button 1 on the keyfob for a long time, then press button 2 briefly CAR l the LED indicator will start flashing l the dimensions will flash once l the door locks will be closed (if the locks are connected to the alarm) KEYFOB l a short signal will sound l the icons corresponding to the armed mode will appear on the screen If the doors, hood, trunk turn out to be poorly closed, and the parking brake is not tightened or the foot brake is pressed, and one of the push-button switches of the doors, hood, trunk, brake is faulty, then the alarm will warn about this with 4 sound signals and 4 flashes of dimensions (see paragraph “Self-diagnosis when arming”). 22 Operating Instructions Auto arming mode In this mode, the security is automatically armed after the ignition is turned off, 10 seconds after all doors are closed. For use this mode it should be programmed in advance (see the section on programming modes using the cursor method, page 19). It is enough to program the mode once, and in the future, automatic arming will occur every time after the ignition is turned off and the car is left. Switch off the ignition and close all doors. The security mode will turn on automatically after 10 seconds. CAR l dimensions will flash 1 time l 1 beep will sound l the door locks will be closed KEY FOB l a beep will sound l the icons corresponding to the armed mode will be displayed on the screen “Checking the serviceability of limit switches”). If the parking brake is not on, the hood or trunk is open, then after the security is turned on, 4 beeps and 4 flashes of dimensions will follow. 23 Switching on the armed mode with the engine running Before switching on the mode, make sure that the hood is closed and the car is neutral gear (or in PARK mode with automatic transmission) and the engine is running. 1 Apply the parking brake and open the door 2 Press button 2 of the CAR key fob l LED indicator will start to burn constantly l dimensions will flash 1 time (Table 2) Remove the ignition key, get out of the car and close all doors Operating Instructions 4 Press the 1 CAR button on the key fob l 1 beep will sound l dimensions will flash 1 time l the ignition zone protection, shock sensor and additional will be disabled. sensor l the door locks will close (if the locks are connected to the alarm) KEY FOB l a short signal will sound l the screen will display icons symbolizing the running engine and armed mode l after the set time of the engine operation, the engine will be stopped without turning off the armed mode 25 Emergency activation of the mode without key fob 1 Open the door with the ignition on CAR l LED will start flashing 2 Press the service button CAR 3 times l LED will go out for about 5 seconds 3 While the LED is off, turn off the ignition CAR l 1 beep will sound l dimensions will flash 1 time l the countdown will start a period of 20 seconds, after which the armed mode will turn on 4 Get out of the car and close the driver's door with the key Make sure that the locks of other doors are closed. 26 Operating Instructions After a 20-second interval, the security will be automatically armed VEHICLE l dimensions will flash 1 time l the LED will start flashing If at the time of arming it turns out that the doors, hood or trunk are not properly closed, and the brake is pressed or the parking brake is off, or is faulty one of the door, hood, trunk, foot or parking brake pushbuttons, the alarm will disarm that zone without any additional warning signals. Cabin Light Bypass (Sensor Activation Delay) A sensor activation delay may be necessary to bypass the door area while the vehicle's interior light fades out, or to calm down the shock or volume sensors. Otherwise, when arming, false warning signals may follow. Depending on programming, a 30, 45 or 60 second delay can be set. Automatic return to armed mode If automatic return to armed mode is programmed and within 30 seconds after disarming the car doors were not opened, the alarm system will automatically re-arm the armed mode. Attention! Locking of door locks will occur if they are connected to the alarm system and the option of auto return to armed mode with locking of door locks is programmed. The switching of the security mode will be confirmed by 1 siren signal and 1 flash of dimensions, then 1 short beep of the key fob will follow. The engine will be blocked. The LED indicator will start flashing to indicate that the vehicle is guarded. If the limit switches of the trunk hood or doors are faulty, then after switching the guard, the following will follow: - 4 flashes of dimensions - 4th siren signals - 1 short beep from the key fob 27 l LED indicator will turn off l 2 beeps will sound l dimensions will flash 2 times l door locks will be opened (if they are connected to the alarm) KEY FOB l 2 short beeps will sound l icons corresponding to disarmed will be displayed unlocked at the same time as disarming. If this mode is enabled, then to unlock the engine, you must additionally perform the actions described in paragraph 2. If 3 signals and 3 flashes of dimensions sound when disarming, this means that sensors were triggered in the armed mode (see paragraph “Self-diagnosis when disarming ”) Two-step disarming 2 28 The second stage of disarming engine interlocks is performed similarly to emergency disarming without a key fob, either with or without entering a personal code (see pages 30-31 of this manual) Operating Instructions Disarming without sound confirmation signals 1 Press button 2 on the key fob twice (The first press is long, the second is short) A CAR l the LED indicator will turn off l the dimensions will flash 2 times l the door locks will be opened (if they are connected to the alarm) KEY FOB l 2 short beeps will sound l the icons corresponding to the off protection If the mode “Two-step shutdown engine lock” is disabled, the engine will be unlocked at the same time as the guard is disarmed. If this mode is enabled, then to unlock the engine, you must additionally perform the actions described in paragraph 2. If 3 signals and 3 flashes of dimensions sound when disarming, this means that sensors were triggered in the armed mode (see paragraph “Self-diagnosis when disarming ”) Two-step disengagement of engine interlocks 2 The second stage of disengagement of engine interlocks is carried out similarly to emergency disarming without a key fob, either with or without entering a personal code (see. 30-31 of this manual) 29 Emergency disarming without entering a personal code The method of disarming without a key fob (with or without entering a code) is determined by programmable function 9, table No. 1. 1 Open the car door with the CAR key l alarms will start or l the dimensions will flash 4 times (if the armed mode was activated without a key fob) There are no beeps when disabling the engine locks in two steps 2 service button three times Within 20 seconds, turn on the ignition and press 3 Switch off the ignition of the VEHICLE l sirens will sound 2 beeps Security is disabled programmable function 9, table No. 1 1 Open the car door with the CAR key, alarms will start or l the dimensions will flash 4 times (if the armed mode was activated without a key fob) l There are no sound signals when disabling the engine locks in two steps 2 Turn on the ignition and press the service button the number of times equal to the first number of the code 3 um from one number, protection will be disabled. If you need to enter the second and third numbers, repeat steps. 2 and 3. Arming disabled If the automatic arming function is programmed, then after turning off the ignition and disarming, re-arm it for at least 10 seconds to prevent automatic arming. 31 Monitoring the status of the alarm, engine and cabin temperature You can use this command in any mode to check the current status of the alarm and check the temperature in the cabin , may differ from the actual temperature in the cabin, as it depends on the installation location of the alarm unit. 1b Press button 3 on the key fob twice KEY FOB l l a melodic signal will sound the engine temperature is displayed for a short time The temperature displayed on the key fob indicator depends on the temperature sensor mounting location that should be taken under protection. VEHICLE l doors, hood or trunk are not properly closed l one of the door, hood or trunk pushbutton switches is faulty l the parking brake is not applied Arm the system (one of the methods) VEHICLE l 4 siren sounds will sound l the dimensions will flash 4 times KEY FOB l 4 short beeps will sound l the corresponding icon is displayed Apply the parking brake, close the doors, hood, trunk VEHICLE l the door locks will be closed (if they were open) l the zone will be set to KEY FOB arming l 1 short beep will sound l the zone of the triggered sensor will no longer be displayed If the cause of a malfunction of the pushbutton switches cannot be eliminated on site, the system will arm and bypass the faulty zone. In case of spontaneous elimination of a malfunction with the armed mode on, the alarm system will immediately automatically arm this zone. 33 Self-diagnosis when disarming The information about the sensors triggered during the armed mode is displayed on the keyfob display after disarming. Disarming by short pressing the button 2 keyfobs CAR l 3 signals will sound l dimensions will flash 3 times KEYFOB l zones of triggered sensors will be displayed on the display If alarms were interrupted from the keyfob then indication of the cause of the alarm, after disarming, will be absent. Control of the number of key fobs in the memory Switch on the ignition and press button 3 on the key fob The number of key fobs recorded in the alarm memory is controlled by the number of flashes of the alarm LED indicator. 34 Operating Instructions Alarm signals If any of the security sensors is triggered in the armed mode, this will automatically turn on the alarm signals: siren signals, flashing parking lights . The engine will be blocked. The keyfob will sound alarms, and the display will show the reason for the alarm. While the siren is sounding, the icon corresponding to the cause of the activation will flash on the keyfob display. While the dimensions are flashing, the vehicle's headlights will flash on the display. Alarms are given in cycles. The duration of one alarm cycle and the maximum possible number of cycles for various alarm causes are shown in the table below. Cause of alarm 1 shock sensor level 2 shock sensor level 1 S o m e n t o n t o n t 2 L e e t o n e t o n e t o n t o n t o n t o n t o n t P r s s e s o n d hood Luggage compartment Ignition B rake Duration 1 alarm cycle No. of cycles and constant n o m s n o m s n o m e f o o r and h and ka S H-1 3 sound in. sig nal a 6 s v et. beeps 1 8 S H-1 2 0 sec beep 2 0 sec. light 1 8 S H-2 3 sound sig nal a 6 s v et. beeps 1 8 S H-2 2 0 sec beep 2 0 sec. light 1 8 3 0 sec. sound 3 5 sec. light 1 8 3 0 sec. sound 3 5 sec. light 1 8 1 no limit 1 no limit 1 no limit no limit no limit 1 no limit DISPLAY icon S A-2 S A-2 30 s 3 5 s . 30 sec. 3 5 sec. 30 sec. 3 5 sec. 30 sec. 3 5 sec. 30 sec. 3 5 sec. sound sound light sound sound light sound sound light sound light sound sound light 1) If after the end of the alarm cycle the cause of the alarm is not eliminated (for example, the doors were left open) , then the corresponding protection zone is temporarily bypassed until the triggering cause is eliminated (until the doors are closed). At the same time, the indication of the cause of operation will remain on the key fob display. 2) If the alarms were interrupted from the key fob, then the count of the number of alarm cycles with a periodically triggered sensor starts anew. 35 Display of alarm signals on the keyfob display Keyfob OK 36 l 1-level shock sensor worked l 2-level shock sensor worked l 1-level additional sensor worked l 2-level additional sensor worked l pressure sensor worked l brake sensor worked l doors opened l open the hood l open the trunk l switch on the ignition Operating instructions Cancel alarms VEHICLE KEYFOB l signals are on l alarms are permanently on l zones of triggered sensors are displayed Press button 2 on the keyfob CAR KEYFOB l the alarms will turn off l the zone in which the sensor was triggered , is temporarily excluded from the security loop l alarms will stop l zones of triggered sensors are displayed l the armed mode is saved After the cause of the alarm is eliminated, KEY FOB indication of triggered sensor zones is stopped l one short beep sounds l 37 Analyzing a temporary power outage will not be successful. When the power is turned off, for example, by resetting the battery terminal, the alarm remembers its state. When the power is restored, the alarm will again be in the same mode (see the status table below), the key fob will give a melodic sound signal. If a self-powered siren is connected to the system, then when the battery terminal is disconnected, the siren will turn on the audible alarms. System state before power failure Armed mode disabled Armed mode enabled Alarm mode, cause of triggering eliminated Alarm mode, cause of triggering not eliminated Immobilizer mode enabled Anti-robbery mode enabled Service mode enabled System status upon power restoration Security mode disabled Security mode enabled Security mode enabled Alarm mode enabled Immobilizer mode enabled Anti-robbery mode enabled Service mode enabled KEYFOB 38 Operating Instructions Blocking the engine Blocking the engine makes all attempts by thieves to start the engine meaningless. If the interlock is made with a normally open type of contacts (see programmable function 10, table No. 1), then it will remain even if the central signaling unit is detected and disconnected from all cables. Immobilizer mode To use this mode, it must be programmed in advance. When the immobilizer mode is programmed, the engine will be blocked automatically, 30 seconds after the ignition is turned off, regardless of the state of the armed mode. 1 To turn off the immobilizer, press the service button, or button 2 on the BRELLO K key fob l two beeps will sound Engine unlocked, armed mode. off 2 Turn on the ignition 39 Programming the immobilizer mode 1 Press and hold button 3 until two beeps sound (first long, then short) KEY FOB l after you release button “3”, the first one from the left will be highlighted in the lower part of the screen icon 2 Short press button 3 3 Press button 1 on the key fob, move the cursor to the “IMMO” icon CAR KEY FOB l dimensions will flash 1 time l will sound sequentially: 2 short beeps 1 melodic 1 muffled signal l the “IMMO” icon will be displayed on the screen The “IMMO” icon is displayed on the screen, the immobilizer function will be activated automatically. The mode is activated when the ignition is on or the engine is running Simultaneously press and hold buttons 1 and 2 of the CAR keyfob l constant sound and light alarms will turn on l the door locks will close (if they are connected to the alarm) l the engine will be blocked either immediately or after pressing the brake pedal (depending on programmable function 8). During the first 30 seconds, blocking occurs in impulses, then the keyfob will continuously sound an alarm l a vibrating signal will be activated l the anti-theft mode icon will appear on the screen 41 Switching off the anti-theft mode with the key fob The first press turns off the alarms, the second press unlocks the engine. 1 Press the button on the key fob 2 CAR the constant beeps and light signals alarm l LED will flash l 2 Press button 2 on the keyfob again to disarm the CAR the arming mode will be turned off the door locks will open (if they are connected to the alarm) l the engine will be unlocked l l 42 the keyfob will sound 2 beeps l the icons corresponding to the disarmed mode l Operating Instructions Hidden activation of the automatic anti-theft mode Please note that the anti-theft mode can only be enabled with the appropriate setting of the programmable function 8, table No. 1. The covert activation of the anti-robbery mode is designed to counter intruders in a situation where it is difficult or impossible to do this in the usual way. The mode is activated when the owner leaves the car, after which the system operates automatically according to a certain algorithm, consisting of several stages. Stage 1 With the ignition on, press the service button for 2 seconds KEY FOB l when the mode is turned on, the image on the screen will not change, however, if necessary, you can press button 3, after which the anti-robbery icon will appear. The second stage is activated automatically after opening one of the doors. Stage 2 Open and close one of the VEHICLE doors l LED continues to flash l dimensions start flashing In the third stage, the anti-theft functions are automatically activated. 43 Stage 3 Expires 30 seconds after opening the door CAR KEY FOB intermittent sound and light alarms will turn on l after another 30 seconds, constant sound and light alarms will turn on l the door locks will close (if they are connected to the alarm) l the engine will be blocked either immediately or after depressing the brake pedal (depending on programmable function 8). During the first 30 seconds, the blocking occurs in impulses, then continuously l an alarm will sound l a vibrating signal will be turned on l Until the alarms turn on, the anti-theft mode can be turned off with button 2 on the key fob car 2 Open 1 CAR l alarms start 2 3 Open the door Close the door while the car is in the car ignition, then hold Open the car door 4 Turn on the 2 service button for 3 seconds 5 Turn off the ignition t 2 siren signals Anti-robbery mode is disabled. Armed mode On To disarm without a key fob, follow the instructions section "Emergency disarming without a personal code" or "Emergency disarming with a set of a personal code", depending on your alarm settings. (Pages 30-31) 45 Turbo Timer Mode Before activating the mode, make sure the hood is closed and the vehicle is in neutral (or PARK for automatic transmission) and the engine is running. 1 Engage the parking brake VEHICLE l the LED indicator will turn on constantly l the dimensions will flash 1 time KEY FOB l a melodious signal will sound l the icon r01, r02, r03 or r04 will be displayed on the screen 2 Remove the key from the ignition, get out of the car and close all doors 3 Press keychain button 1 CAR l 1 beep will sound l the dimensions will flash 1 time l the protection of the ignition zone, shock sensor and additional will be disabled. sensor l the doors will be locked (if the locks are connected to the alarm) 46 KEY FOB l a short beep will sound l icons will be displayed on the screen symbolizing the running engine and armed mode Operating Instructions Programming the turbo timer mode 1 Press and hold button 3 until two beeps sound (first long, then short) KEYFOB l after you release the button 3, the first left icon 2 will be flashing at the bottom of the screen 3 Short press the button 3 to move the cursor to the “TURBO” icon dimensions will flash 1 time l will sound in sequence: 2 short beeps 1 melodic signal l the “TURBO” icon will be displayed on the screen While the “TURBO” icon is displayed on the screen, the turbo timer function will be activated automatically . The 1st level shock sensor will be disabled, giving warning signals KEYFOB CAR l 2 flashes of dimensions l a melodic signal will sound l the symbols of temporary shutdown of the 1st level of the shock sensor will be displayed 2 Press the button 1 of the keyfob twice briefly. Both levels of the shock sensor will be disabled. CAR l 3 flashes of dimensions KEY FOB l 3 beeps will sound l icons of temporary deactivation of both levels of the sensor will be displayed 3 Press the button 1 of the key fob twice briefly. The shock sensor will be re-enabled During one security cycle, you can turn off the shock sensor by levels and turn it back on an unlimited number of times. The 1st level of the additional sensor will be disabled, giving warning signals VEHICLE l 2 flashes of dimensions 2 l a melodious signal will sound l the symbols of temporary disablement of the 1st level of the additional sensor will be displayed Press the keyfob button 2 briefly twice. Both levels of the additional sensor will be disabled. CAR l 3 flashes of dimensions 3 KEY FOB KEY FOB l a melodic signal will sound l icons of temporary deactivation of both levels will be displayed Press the button 2 of the key fob twice briefly. The shock sensor will be re-enabled If two separate sensors are programmed, then only the 1st sensor is disabled or both together. The channel is activated by the same actions, regardless of the selected option l 3 flashes of dimensions l 3 short sound signals l 3 sound signal l the trunk lock opens l the shock sensor and add. sensors If the trunk does not open when the channel is activated, then the indication of an open trunk and disabled sensors on the key fob display will not follow. If at the time of closing the trunk the alarm is armed, then the zones of the trunk, shock sensor and additional sensor will be armed again after 5 seconds. In confirmation, 1 beep will sound from the key fob. The channel can be programmed for any fixed duration from 1 to 60 seconds. If option 2 is selected, the shock sensor and the additional sensor are disabled during the operation of the additional channel. The type of additional equipment connected to channel No. 1 is specified when setting the alarm. There are 4 options for the operation of additional channel No. 2. Press the button 2 CAR on the key fob l the LED indicator will turn off l 2 beeps will sound l the dimensions will flash 2 times l the locks of only the driver's door will be opened KEY FOB l 2 short beeps will sound l the icons corresponding to the disarmed protection will be displayed To unlock the remaining doors, press button 2 of the key fob again. The driver's door actuator and the other door actuators must be wired according to the two-step unlock pattern. The channel can be programmed for any fixed duration from 1 to 60 seconds. If option 2 is selected, the shock sensor and the additional sensor are disabled during the operation of the additional channel. l 3 flashes of dimensions l 3 sound signals The type of additional equipment connected to channel No. 2 is specified when the alarm is installed. 51 Additional channel control 3 Options for additional channel operation are determined by programmable function 15, table No. 1. There are 4 options for the operation of additional channel No. 3. Channel activation is carried out in the same way, regardless of the selected option. Press button 3 on the key fob twice (The first press of button 3 is long, the second is short) 60 sec Option 4 - latch mode (switching on and off with a remote control) The type of additional equipment connected to channel No. 3 is specified when setting the alarm. Auxiliary channel operation 4 Auxiliary channel operation options are determined by programmable function 12. There are 2 options for the operation of additional channel No. 4. The channel is activated automatically. Option 1 or 2 channel outputs are used, for example, to turn on the “polite illumination” of the interior or automatically raise the windows when the armed mode is turned on. Operating Instructions 52 Option 3 Call from the car To send a call signal from the car to the alarm key fob, press the button located on the body of the transceiver module. The key fob display will show the “CALL” icon and the 20 second call sounds will sound. To interrupt the sound signals of a call, press button 3 on the key fob. Light indication of open doors If programmable function 7 is enabled, then the flashes of dimensions will warn you that the doors are open. The duration of the warning lights can be programmed to 10, 20 or 30 seconds. Control of the battery charge of the remote control with LCD The indication of the low battery is updated by any press of the button l in case of a low battery, the icon will appear Control of the health of the limit switches Option 1 or 2 The alarm provides the ability to monitor the health of the door, hood and trunk limit switches when the security mode is off. Opening the doors, hood and trunk with the ignition on should be accompanied by flashes of the LED indicator. If the LED does not light up when they are opened, the corresponding limit switch is defective. 53 Starting the engine Before starting the engine from the key fob or activating automatic engine starts, it is mandatory to familiarize yourself with the following features of the engine start functions: 1. For successful implementation of the remote or automatic engine start functions, the following parameters must be programmed at the alarm setting stage: - type of car gearbox - manual gearbox (manual gearbox) or automatic transmission gears (automatic transmission). To do this, on vehicles with a manual transmission, it is necessary to cut the black loop in the wiring harness of the 18-pin connector of the central unit. On vehicles with automatic transmission, the loop in the 18-pin harness must be retained. - type of car engine - gasoline or diesel. To do this, enter the programming mode of function 2.10 and, depending on the type of engine, set the required delay time for turning on the starter after turning on the ignition at the first attempt to start the engine. For diesel engines, the starter turn-on delay required to warm up the candles is 4, 6, 10 seconds. For gasoline engines the delay is fixed - 4 seconds. - for cars with a start button - program function 8 (table 2) for option 3. 2. Remote engine start cannot be carried out in the following cases: ignition on, hood open, parking brake off or foot brake applied, engine start preparation not completed on vehicles with manual transmission. 3. In one start cycle, the system can make 4 attempts to start the engine. If after the 4th attempt the engine does not start, then on the display of the key fob with feedback (provided that it is in the reception area) the inscription “SP” will be displayed and the key fob will give 4 beeps, indicating the end of attempts to start the engine. 4 flashes of dimensions will follow. 54 Operating instructions. 4. The maximum time for the first attempt to crank the starter can be programmed by setting the alarm to 0.8; 1.2; 1.8 sec or 3.6 sec for any engine control. The time of each subsequent attempt to scroll the starter during one start cycle is automatically increased by 0.2 seconds. 5. If the engine is started before the expiration of the maximum starter cranking time, the starter is turned off ahead of schedule. 6. If running engine stalls before the end of the programmed warm-up time, a new engine start cycle will be attempted. 7. The automatic engine start function by temperature can be enabled regardless of the state of the alarm or timer auto engine start functions. 8. Simultaneous activation of the functions of automatic engine start by alarm clock and by timer is not possible. Attempting to enable functions at the same time will result in the activation of the function that was activated last. 55 Preparing to start on vehicles with manual transmission Before starting the engine on vehicles with manual transmission, it is necessary to perform the “soft neutral” procedure. Software Neutral is a specific course of action the driver takes to ensure that, in a vehicle prepared for launch, the gear stick will remain in position. neutral position . Accordingly, starting the engine with the gear engaged will be impossible. Software neutral, depending on the state of the programmable function 12 (table 2), can be performed in two versions: automatic or controlled by a key fob. Switching on the “software neutral” Automatic option 1 CAR l the LED indicator will start to burn constantly l the dimensions will flash 1 time KEY FOB l a melodic signal will sound l the icon r99 will be displayed on the screen l if the turbo timer mode is programmed, the icons r01, r02, r03 or r04 will be displayed 56 Operating Instructions 2 Get out of the car and close all doors. The engine continues to run 3 Press the 1 CAR button on the key fob l 1 beep will sound l the dimensions will flash 1 time l the door locks will be closed (if the locks are connected to the alarm) l the engine will stop l if the turbo timer is programmed, the engine will run for the set time KEY FOB l a short beep will sound l icons will be displayed on the screen, symbolizing the armed mode if the turbo timer is programmed l the icons of the running engine and armed mode are displayed on the screen The engine is ready for launch 57 Switching on the “software neutral”. Keychain control option. 1 2 Press the button 2 CAR on the key fob l the LED indicator will start to burn constantly l the dimensions will flash 1 time the key fob l a melodic signal will sound l the icon r99 will be displayed on the screen l if the turbo timer mode is programmed, the icons r01, r02, r03 or r04 will be displayed 3 58 Remove the ignition key , get out of the car and close all doors. The engine continues to run Operating Instructions 4 Press the 1 CAR button on the key fob l 1 beep will sound l the dimensions will flash 1 time l the door locks will be closed (if the locks are connected to the alarm) l the engine will stop l if the turbo timer is programmed, the engine will run for the set time KEY FOB l will sound short beep l icons will be displayed on the screen, symbolizing the arming mode if a turbo timer is programmed l the icons of the running engine and armed mode will be displayed on the screen The engine is ready for start For a car with a manual transmission, the “software neutral” procedure was performed. For vehicles with automatic transmission, the control lever is in the “PARK” position 1 Press button 1 on the key fob for a long time, then button 3 shortly sensor l LED indicator will light up constantly KEY FOB l a short beep will sound l icons will be displayed on the screen symbolizing the running engine and armed mode l warm-up time is displayed by icons r10, r20, r30 or r99 ​​In one start cycle, the system can make 4 attempts to start the engine . If after the 4th attempt the engine does not start, then on the display of the key fob with feedback (provided that it is in the reception area) the inscription SP will be displayed, and the key fob will give 4 beeps, indicating the end of attempts to start the engine. 4 flashes of dimensions will follow. 1 minute before the end of the engine warm-up, the inscription r01 is displayed and 2 series of 4 sound signals from the key fob will sound. After the end of the engine warm-up time and its automatic stop, 4 flashes of dimensions will appear. The r00 icon will be displayed on the keyfob display, 4 keyfob beeps will sound. 60 Operating Instructions Remote extension of engine operation 1 Press button 1 on the remote control for a long time, then button 3 briefly CAR l the engine continues to run l the dimensions will flash 1 time KEY FOB l a melodious signal will sound l each press of the buttons increases the engine operation time by 5 minutes Remote engine stop 1 Press button 2 on the remote control for a long time, then button 3 briefly CAR l dimensions will flash 4 times KEY FOB l a melodious signal will sound l the icons symbolizing the operation of the engine will disappear on the screen engine at the set time using the key fob alarm, first check that the current time on the key fob is set correctly. Then program the keyfob alarm for the desired engine start time and turn on the alarm (see page 12). The enabled alarm mode is indicated by an icon on the keyfob display. After checking the current time and setting the alarm, successively press buttons 3 and 1 of the keyfob, place the cursor on the icon and turn on autostart by alarm (see page 13). 1 flash of dimensions will follow. A melodious sound signal from the remote control will sound and an icon will appear on its display, indicating, together with the icon, the enabled autostart mode by alarm clock. For a short time, the keyfob display will show the set future start time, which will then change to the current time. The LED indicator will flash in series of 2 flashes. To turn off the autostart function on an alarm, place the cursor on the icon again and press button 2 on the key fob. 2 flashes of dimensions will follow. The melodic signal of the key fob will sound, the icons will disappear .. Note 1). The presence of a key fob in the coverage area of ​​the transceiver at the time of the engine autostart by alarm is not required. 2). The engine start time may differ from the programmed alarm time within 1 minute. 3). The autostart function is enabled for one startup cycle. For a new start of the engine, it is necessary to activate the function again from the key fob each time. Automatic start of the engine by timer (activated from the key fob) To enable the function of automatic start of the engine by timer every 2, 3, 4, 24 hours (programmable function 2.3), by successively pressing buttons 3 and 1 of the key fob, place the cursor on the icon and turn on auto start by timer (see page 13). 1 flash of dimensions will follow. A chime will sound. An icon will appear on the keyfob display indicating the enabled autorun timer mode. The LED indicator will flash in series of 2 flashes. Simultaneously with the activation of the function, the engine will start and warm up during the programmed time. To turn off the autorun function by timer, place the cursor on the icon again and press button 2 on the remote control. 2 flashes of dimensions will follow. A melodic signal from the key fob will sound, the icon will disappear. or -25°C (function 2.4). The engine warm-up time is determined by the programmed function 2.2. The alarm monitors the sensor readings immediately from the moment the function is activated. The minimum interval between repeated autostarts, counted from the moment of the previous start, excluding the engine warm-up time, is 1 hour. After activating the temperature start function, the number of engine autostarts is not limited by temperature. To enable the function of automatic engine start based on temperature, place the cursor on the icon and enable autostart based on temperature (see page 13). 1 flash of dimensions will follow, and a melodic key fob signal will sound. The key fob display will display an icon indicating the enabled autostart mode by temperature, and the temperature value at which the engine will blink. The LED indicator will start, for example, in a series of 3 flashes. To disable the autostart function by temperature, place the cursor on the icon again and press button 2 on the remote control. 2 flashes of dimensions will follow. A melodious signal from the key fob will sound, the icon will disappear. 1 siren chirp KEYFOB l 1 chirp will sound Repeat step 2 for all keyfobs to be recorded. The interval between the recording of each key fob should not exceed 5 seconds. Successful recording of each new key fob is confirmed by the corresponding number of siren signals. Switch off the ignition. In confirmation of the exit from the keyfob recording mode, 5 flashes of dimensions will follow. Attention! When writing new key fobs, it is necessary to overwrite the old ones, otherwise they will be deleted from the alarm memory. To record a 2-button key fob without a display, use a combination of buttons 1 and 2 (simultaneously press and hold until confirmation) x digits. Each digit of the code can take a value from 1 to 6 inclusive. The algorithm for programming a personal code is as follows: 1. Enter the function programming mode and select one of the options for a personal emergency shutdown code (programmable function 9). The PIN CODE icon should appear and lock on the key fob display. 2. Enter the PIN-code setting mode. To do this, with the ignition off, press the service button 4 times. Each press is accompanied by the lighting of the LED indicator. 3. Turn on the ignition. 4 siren beeps will follow. 4. Press the service button once. 1 siren signal will confirm entering the mode of setting the first digit of the code. Within 5 seconds, by pressing the remote control buttons, enter the first digit of the personal code in accordance with the table below. Code number 1 2 3 4 5 6 Pressing the remote control buttons One short press of button 1 One short press of button 2 One short press of button 3 Two presses of button 1 (the first press is long, the second is short) Two presses of button 2 (the first press is long, second - short) Two presses of button 3 (first press - long, second - short) Siren signals 1 2 3 4 5 6 Follow the steps described above for the second and third digits of the personal code if you decide to set 2 or 3- x digit personal code. 5. Exit from the personal code setting mode occurs after the ignition is turned off or automatically if no action is taken within 10 seconds. 5 flashes of dimensions will follow. 65 Programming security and service functions Some security and service functions and alarm operation parameters can be changed using the service button and key fob without having to access the central unit. The list of functions is given in the tables. The programming procedure is described in detail in the instructions for installing the StarLine B9 alarm. We do not recommend programming on your own, but contacting the specialists who installed the alarm. Changing programming parameters or resetting to factory settings may cause the engine to lock up during normal startup, as well as wrong work standard electrical equipment and the alarm itself. Programmable function Long + short pressing of button 1 4 beeps Single pressing of button 1 Single pressing of button 2 Single pressing of button 3 1 beep 2 beeps 3 beeps comfort 30 / 0.8 sec #1 - duration of door lock control pulses 0.8 / 0.8 sec 3.6 / 3.6 sec double locking impulse 0.8 / 0.8 sec No. 2 - automatic control of door locks from the brake pedal / off. ignition from ignition on/off only ignition closing disabled up to 60 sec no delay 30 sec 45 sec no locking without locking two 1-level add. sensor No. 3 - bypassing the cabin light and delaying the activation of sensors when arming No. 4 - automatic arming and signal processing algorithm of the additional sensor No. 5 - automatic switching of the security mode No. 6 - algorithm and duration of the output to the siren 66 with locking locks 2-level additional . locking sensor two 1-level add. sensor with locking without locking per siren 100 ms per siren 50 ms 2-level add. sensor disabled for horn 50 ms for horn 20 ms Operating instructions Single pressing of button 1 Single pressing of button 2 Single pressing of button 3 1 beep 2 beeps 3 beeps Long + short press of button 1 4 beeps No. 7 – light indication of open doors 10 sec 20 sec 30 sec disabled No. 8 - algorithm for blocking outputs when the anti-robbery mode is turned on When the brake is turned on When the brake is turned on and without a pin code 1-digit pin code 2-digit pin code 3-digit pin code No. 10 - activation of outputs to blocking of the engine NC NC NC together with the DRR relay NR together with the DRR relay No. 11 - 2-step disengagement of engine blocking disabled No. 12 - additional channel algorithm No. 4 (blue wire) 1-60 sec when disarming and off. ignition 13 sec. when on armed 1-60 sec when armed 13 sec. when on protection No. 13 - additional channel No. 1 algorithm (yellow-black wire) 0.7 sec open. trunk 1-60 sec (with shock sensor disabled) 1-60 sec (without shock sensor disabled) latch (on/off key fob) 0.7 sec 2-step unlocking 1-60 sec (with shock sensor disabled ) 1-60 sec (without shock sensor off) latch (on/off keyfob) 0.7 sec 1-60 sec (with shock sensor off) 1-60 sec (without shock sensor off) latch (on/off keyfob) Programmable function No. 9 - alarm emergency shutdown algorithm No. 14 - additional channel algorithm No. 2 (yellow-red wire) No. 15 - additional channel algorithm No. 3 (yellow-white wire) anti-robbery mode disabled enabled Factory presets are shown in gray in the table . 67 Programming startup parameters We do not recommend doing programming on your own, but contacting the specialists who installed the alarm. Changing the programming parameters or resetting to factory settings can cause the engine to block during a normal start, as well as incorrect operation of the standard electrical equipment and the alarm itself. Programmable function No. 1 - the duration of the turbo timer mode No. 2 - the duration of the engine after starting No. 3 - intervals for automatic engine start according to the timer No. 4 - automatic engine start according to temperature No. 5 - engine start mode No. 6 - state of dimensions with the engine running No. 7 - locking the door locks when the engine is stopped when the security mode is on Single pressing of button 1 Single pressing of button 2 Single pressing of button 3 1 beep 2 beeps 3 beeps Long + short press of button 1 4 beeps 1 min 2 min 3 min 4 min 10 min 20 min 30 min without limitation 2h 3h 4h 24h - 5OS - 10OS - 18OS - 25OS with arming without arming ON constantly without arming without arming off off off flashes off on on on on option 1 = ACC option 2 = IGN 1 option 3 start/stop button mode option 4 1 impulse No. 9 – duration of starter scrolling 0.8 sec 1.4 sec 2.0 sec 3.6 sec No. 10 - engine type gasoline diesel (option 1) diesel (option 2) diesel (option 3) by voltage by generator (+) by generator (-) by tachometer automatically from key fob from key fob from key fob No. 8 - operation algorithm output (blue wire 6pin. No. 11 - engine operation control by: No. 12 - activation of ignition support when the engine is running ) short Icons any except off Arming off any except Arm (without sound confirmation) sequence. off Enable silent arming of sequences. off Arm with engine running short on off any except off any except off any except Disarm (with audible confirmation) short off Disarm (without audible confirmation) sequence. off short does not depend on any does not depend on double does not depend on any does not depend on does not depend on any does not depend on Alarm status, interior temperature Car search, engine temperature Turn on panic on any except for a long time until on 69 Basic key fob commands, continued Press Condition Com anda Ignition Icons Security CLOSE LOCKS SHORT ON OFF Open LOCKS SHORT ON double off yu ch e n i e d o p. level sensor double off Control (channel 1) independent any independent control (channel 2) independ ent any indepen dent i n d i n d e n t i n d i n t i n g t i n g t i n g o n t i n g e n t i n g o n t i n t i o n s . s o n d S e c t e m o n o r stop. o f any except any other than any other than any other than in c o n n e d e n t h e a n d e n t a n d e n t o n d o n d o n t Turn anti-robbery on on off Block as button for a short time does not depend on any of the unblocking buttons for a short time any do not depend in succession double press two buttons at the same time first long press, second short press - two short presses of one and the same Buttons Commands to set up the key fob with LCD display C ommand Entering the setup mode Change mode 70 Press Indica tion continuous up to + + Time (hours, minutes) Alarm clock (hours, minutes) Alarm clock (incl. /off) TIMER (hours/m inu tes) TIMER (on/off) short Incre n or and switch on briefly Decrease or switch off Brief Instructions for use KEYFOB Commands selected by the cursor of the keyfob with LCD display cursor movement short Turn on the icon selected by the cursor shortly Turn off the icon selected by the cursor shortly disable or disable autostart mode by timer or shortly Enable or disable autostart mode by temperature or shortly Enable or disable service mode or shortly Set or and cancel turbo timer or briefly Set or cancel automatic arming or briefly Set or cancel immobilizer mode or briefly 71 Keyfob batteries and their replacement Keyfobs use various batteries: the key fob with feedback uses 1 “AAA” 1.5V battery in the key fob without feedback 1 CR2450, 3V battery is used The operating time of the remote control batteries depends on: installed element nutrition. The capacities of commercially available batteries may vary by several times. The average battery life can be: for a remote control with feedback from 6 to 9 months for a remote control without feedback from 9 to 12 months When the battery is low, an icon is displayed on the indicator of the remote control with feedback, which indicates the need to replace it. Replacing the battery in the key fob with feedback is carried out in the following order: 1. Open the battery cover of the key fob and remove the old battery. 2. Install new element supply, observing its polarity. The correct position of the battery is indicated on the key fob housing under the cover. Close the fob cover. 3. After replacing the battery, correct the current time. Replacing the battery in the key fob without feedback is carried out in the following order: 1. Separate the body halves with a thin object. 2. Remove the old battery and install a new one, observing the polarity. Correct position battery is indicated on the contact of the holder. 3. Place the body halves together and squeeze them together until they click into place. 72 Operating Instructions Warranty obligations Warranty service for this type of equipment is carried out by the company that sells it, subject to the conditions specified below. The quality of the installation of the equipment is confirmed by the relevant warranty documents of the installer. Terms of warranty service 1. The warranty is valid for the period specified in the warranty card for this type of equipment. The period is calculated from the date of purchase of the equipment, provided that the consumer observes the conditions of operation, installation and storage. 2. During warranty period produced free repair equipment or replacement of defective parts or components. The warranty period is extended by the time the equipment is under warranty repair. 3. Warranty repair of equipment (or, if it is impossible, replacement) is carried out within the period valid at the enterprise that sold this equipment, with a mandatory statement of a claim to the quality of the product. 4. Free of charge warranty repair or replacement of equipment is made only in the event of a manufacturing defect. The conclusion about the nature of the defect is made at the certified service center of the supplier. 5. To submit a claim for the replacement of defective equipment, the necessary conditions are the presence complete set delivery, including packaging accessories - box, bags, description of operation and installation, as well as the presence of a completed warranty card. 6. The warranty is invalid in the following cases: · in the absence or incorrect filling of the warranty card (card); in case of violation of the factory seals (if they are provided for by the design) or if there are traces of opening the equipment; When traces are found mechanical damage or damage caused by non-compliance with the requirements of storage or operation (traces of impacts, cracks, abrasions or scratches on cases, etc.); · in case of damage to the product caused by unqualified installation or damage directly or indirectly caused by external causes (fire, natural disasters, water, aggressive liquids, etc.). 7. The warranty does not cover batteries used in remote control fobs, pager receivers, or any other consumables supplied with this type of equipment. 8. In the event of defects or damage not related to manufacturing defects and after the expiration of the warranty period, the equipment is diagnosed and repaired in accordance with the current prices of the supplier. 73

Alarm Starline B9 – simple system security with two-way communication and auto-start of the engine. Since 2007, this alarm has been actively installed on new cars, like domestic production, and foreign cars.

Many drivers use this equipment to this day, noting the reliability and stability of its operation.

Main features of Starline b9

In addition to remote engine warm-up, the Starline b9 alarm system has the following characteristics:

• changing code that effectively fights signal interception by code grabbers;
• noise immunity in urban environments;
• Feedback. Information about the state of the car is reflected on the key fob display;
• two key fobs: one with LCD display, the second without it;
• range in pager mode up to 1200 m, and in control mode up to 600 m;
• 9 protected zones, including blocking the engine using a relay;
• turbo timer mode, which allows you to install protection on a turbocharged engine;
• programmable functions that the owner sets at his discretion;
• 4 control channels that can be connected optional equipment, such as window closers that implement the "Comfort" mode.

In addition to the standard version B9, the manufacturer offers Starline modifications dialog, equipped with dialog coding, and Starline twage b9 with increased noise immunity and several additional software features.

Complete set and cost of autoprotection

The car alarm kit includes the following items:

• control unit (processor);
• antenna and temperature sensor in a plastic case;
• main keychain for car alarm Starline b9 with screen and backlight;
• additional keychain (without screen);
• shock sensor;
• service key Valet;
• LED signal on the windshield;
• end buttons for the hood and trunk;
• wiring with plugs for connection;
• instructions for car alarm Starline b9 in Russian.

The last cost of the B9 security system was approximately $63. IN this moment the alarm is not issued. The manufacturer recommends installing modified versions with B96 autorun instead.

Consider the advantages and disadvantages of the B9 car security system.

Advantages	Flaws
Feedback. The alarm key fob gives sound and light signals, letting the driver know that the system has been triggered.	Small signal radius. Despite the parameters declared by the manufacturer of 600 and 1200 meters, in practice the range is much lower. This is due to the presence of obstacles and interference in the signal path.
Autorun. This function significantly increases the comfort of using the car, as it allows you to warm up the engine and interior before driving.	The fragility of the key fob buttons. After several years of operation, in most cases, the key fob buttons begin to fail and require repair.
Effective protection. The signal that the transmitter sends to the remote control is constantly changing and requires a certain response from the key fob. Such a system eliminates the use of code grabbers to select a cipher.	Lack of CAN bus connection. Modern cars equipped digital buses, for connection to which a special module is required.
Ease of installation and management. Using the Starline b9 alarm is easy and convenient. It has a clear menu in Russian. If you have skills in working with automotive electrical equipment, you can install the system yourself.	Lack of GPS-GSM signal. Control from a mobile phone and the ability to track the status of the car on the site is an advantage of newer models. This function can be connected additionally by mounting the StarLineSpace module into the system.

1. Control panel failure.
The most common complaint of Starline b9 owners is the breakdown of the key fob buttons, without which the operation of the system becomes impossible.
You can solve the problem by disassembling the remote control and wiping the contacts with alcohol. If the keys have fallen inward, you can change them at the service center.

2. Alarm malfunctions, poor communication signal.
The B9 alarm does not cope well with radio interference, which is especially abundant in big city. Unfortunately, this shortcoming cannot be corrected. The owner of the car can only make sure that the vehicle is as little as possible in the zone of strong radio interference.

Connection diagram Starline B9. How to install an alarm yourself

The security system is connected according to the diagrams that are presented in the instructions for the alarm. For experienced motorists, the Starline b9 car alarm connection diagram is quite simple. For those who have never encountered the installation of such equipment, the manufacturer recommends contacting professionals.

Owner reviews

Positive and negative opinions of drivers who used B9 are taken from the websites http://mobilradio.ru/, www.autoelectric.ru, www.autoradioservice.ru

Positive	Negative
Very good alarm for the money. I took the twage version. Good range, even through metal walls, for example, if it is in a garage. Feedback is also a cool thing, you always know if something is wrong with the car. As a fisherman who often leaves the car in a deserted place, it is very convenient for me.	I would never buy a second time! I only spoiled my nerves with this alarm. Glitches constantly. Autorun does not turn on, or turns on when she wants to. The key fob does not work properly. Once I got stuck at a car wash, I could not get into the car, the second time I was in the country. I had to unplug the unit to turn it off. I do not recommend this product to anyone, do not mess with it!
The Singalka turned out to be very tenacious. It has been on an SUV for more than 5 years. Got into water and mud. Keychain fell several times from a decent height. And nothing, it works. Reliable system, albeit a simple one.	Despite the presence of a hologram, the alarm reminds Chinese fake. The scheme is somehow clumsy, it is not clear why everything is connected like that, when everything can be done much easier. The key fob is very flimsy, the body cracked after a slight fall.
I don’t know why some people write negative reviews, starline b9 worked fine for me for about 4 years. Always clearly opens and closes the first time. In vain does not work, well, maybe a couple of times it happened. I think that professionals should install such systems, and those who undertake it themselves create unnecessary problems. I was installed at the station, and everything works without problems!	I had one like this a couple of years ago. Doesn't work well, crashes all the time. Often works, and for some reason at night. I used this alarm for 3 days and returned it back. Well, at least the service agreed to dismantle it.
Conventional, reliable and inexpensive alarm system. Everything you need is in it, and if someone wants to steal specific car, he will do it anyway, with any guard. Particularly pleased with the engine warm-up, for our climate it's just a godsend! I did the repair only once, and even then it was insignificant - I soldered the contacts on the antenna unit.	It stands on the Volga for me. It's been a long time since I installed it. In general, a good, but already outdated model, it makes no sense to put it on new cars. Firstly, theft protection is weak, and secondly, it cannot be connected via a digital bus.
I chose B6 Starline because it has a turbo timer and it has auto start. I use 3 years serious problems did not arise, with the exception of replacing the key fob, since the buttons on it began to stick over time.	I bought myself a Ten and my wife a Toyota. In our yard, cars began to be robbed often, we decided to put signaling. What can I say about this model? If we get lucky. I began to fail in just a month or two. It works fine for my wife, sometimes she says that it is not removed the first time. It was put by the same person, a proven master.

Having studied the reviews of the owners, we can conclude that B9 is one of the most successful models Starline, which is very popular among the people. This system owes its fame to the advanced, at the time of release, protective functions, as well as convenience in everyday use and ease of installation.

A huge plus of StarlineB9 is the presence of automatic engine start. This function, although not a security feature, is considered practically mandatory for modern systems, as it provides comfort and saves time for warming up. To date, it cannot be said that this system provides the most reliable protection, but it can still successfully guard the car, notifying the owner of a possible break-in using feedback from the key fob.

Instructions for Starline B9

Typical instruction car alarm B9 consists of:

• descriptions general characteristics systems;
• descriptions of the operation of the key fob and decoding of symbols on the screen;
• basic signaling functions to ensure protection;
• comfort functions of a two-way car alarm;
• additional programmable features;
• user manual and step by step installation equipment.

Video - Overview of the Starline twage B9 car alarm. Autostart Reviews Operating experience

Video - How to install an alarm with auto start StarLine B9 on Toyota Cresta 1995 DimASS

StarLine B9 - car alarm system with two-way communication and smart start engine. The alarm is completed with a convenient remote control with a friendly LCD display. The key fob has a warning range of up to 1.2 km. StarLine B9 protection against intellectual hacking is ensured by the use of dynamic code radio control StarLineProPlusTM, protected from selection and interception by a dialogue coding algorithm "friend or foe". The process of remote start and control of the engine of any type is provided by a specialized processor. StarLine system B9 can be installed on any car with petrol, diesel or turbocharged engines, automatic or manual transmission. More than 60 standard and programmable functions provide the car owner with not only reliable protection, but also comfort when using the StarLine B9 car alarm.

Peculiarities StarLine Twage B9

• Double-sided keychain with a liquid crystal indicator with the ability to display events in real time
• The maximum range of the key fob in transmitter mode is 600m (declared by the manufacturer)
• The maximum range of the key fob in pager mode is 1200m (declared by the manufacturer)
• Dynamic control code, protected from selection and interception by a dialogue coding algorithm "friend or foe"
• Remote and automatic engine start function
• Automatic control of the location of the key fob in the reception area
• 9 protected zones of the car
• "Turbotimer" mode
• Ability to work with security and search GSM/GPS StarLine module Space
• 4 additional control channels

StarLine Twage B9

1. Keychain remote control with LCD display and feedback	1 PC.
2. Key fob remote control without feedback	1 PC.
3. Central processing unit	1 PC.
4. Transceiver module with antenna, emergency call button and temperature sensor in the car interior	1 PC.
5. Engine temperature sensor	1 PC.
6. Two-level shock sensor	1 PC.
7. LED indicator	1 PC.
8. Valet service button	1 PC.
9. Hood button	1 PC.
10. Cable set	1 PC.
11. User's note	1 PC.
12. Instructions for use and installation	1 PC.