Car sills - one of the parts car body which is most susceptible to aggressive influence environment... Changes in temperature, high humidity, harsh chemicals that are sprinkled on roads in winter period- all this has an extremely negative effect on paintwork body.

Thresholds on a car, why thresholds, bottom of doors and arches very quickly become unusable

Sooner or later, a corrosion process starts on the surface of vulnerable parts of the body. First of all, the thresholds, the bottom of the doors, and the arches of the car "suffer". In addition to rust, the above-mentioned body elements are subject to regular influence of torsion and bending moments, as well as strong vibrations... Very often, dents appear on the surface of the thresholds due to the fault of the car owner himself, as a result of improper use of the jack. However, in this case, the thresholds can be repaired on their own. Sometimes you need to replace inserts, apply a patch, or do other repair work, which will be discussed below.

Corrosion of metal, the cause of rapid corrosion

The corrosive process very quickly turns metal into rusty dust. For example, of all "black" metal produced in the world, 10% of rust kills in the first year. The two main causes of metal corrosion are electrochemical and chemical.

chemical corrosion

Chemical corrosion spares neither ferrous nor non-ferrous metals.
This process takes place in an environment that does not conduct electricity(dry gas mixtures, alcohols, various kinds of oil products, etc.). The intensity of the process can increase in parallel with an increase in the ambient temperature. As a result, a characteristic oxide film appears on the metal surface.

electrochemical corrosion

For the full flow of this process, a thin electrolytic film is sufficient on its surface, which ordinary water can also form. However, the most common cause of electrochemical corrosion is the total use of technical and household salt, which are sodium and potassium chlorides, and are used to remove ice and snow on roads in winter. Chlorides affect not only cars, but also underground utilities. For example, in the USA alone, the annual losses from the use of salt are more than $ 2 billion.

Thresholds on a car, what kind of thresholds are there

According to the material of manufacture, thresholds are divided into plastic and metal. The plastic option is the cheapest, but also the most short-lived. Plastic sills almost always go to standard configuration cars and deteriorate very quickly.

Metal thresholds are much more durable and reliable. The choice of metal thresholds is quite diverse - the material of manufacture can be an aluminum profile, stainless steel, alloys with chromium, etc.

Especially for fans car tuning manufacturers make custom-made special backlit pads that are connected to the wiring, and the lamps light up when the doors are opened. At the same time, the thresholds are illuminated with pleasant light, which not only gives the car original view, but also helps to comfortably get in or out of the car in dark time days.

Removable sills, welded sills, what's the difference

According to the method of connection with the body, car sills can be removable or, as they are also called, movable, as well as welded to the car body.

Removable car sills are made of plastic or metal and are attached to the body with self-tapping screws. In the event of a need for repair, such thresholds are very easy to remove, perform necessary work and attach back.

Special tools for repairing thresholds

To repair removable thresholds you will need:

Workbench.
Anvils.
Mallet, other tools for straightening metal.

To repair non-removable thresholds you need:

Workbench.
Spotter or welding machine.
Manual extraction, for smooth and gentle removal of dents.
Hammers for support and straightening.
Anvils.
Bulgarian.
Other locksmith tools.

Removable thresholds, when it is possible to restore removable thresholds, and in what cases it is better to put new ones

With minor damage, you can repair the removable thresholds yourself. Such work is mainly carried out without using a welding machine - it is enough to make a straightening or a hood. If you work carefully, it is even possible to do without painting the part, because although the threshold is removable, such work is considered a body repair.

The dents are pulled out carefully, taking care not to damage the paintwork. If traces of corrosion are found on the threshold, the degree of damage must be assessed. If it is negligible, you can get by with a small patch. With a larger-scale damage to the threshold by corrosion, there is no particular point in repairing - the part is easier and faster to replace.

As mentioned above, thresholds are often damaged not only from stones and curbs, but also from an incorrectly installed jack when replacing a wheel. Before proceeding with the removal of dents and other repair work, it is necessary to assess the severity of the damage, and then select necessary tools and materials.

With small and medium severity of damage, you can repair the welded thresholds yourself. To remove dents or small distortions without damaging the paint, a cooker hood and a plotter are used.

If the dents are deep and cannot be pulled out, then a rectangular hole is made in the side of the threshold into which the anvil is inserted. After that, the dent is carefully leveled with a straightening hammer.

The main methods of repairing car thresholds using welding are replacing welded thresholds, and installing patches on damaged places.

If the damage is serious enough, cuts are made in the metal in several places. After the end of the straightening work, the cuts are closed with patches. When the threshold is damaged by corrosion damaged areas cut out with a grinder, make a pattern, along which a patch is then cut out. The patch is welded onto the damaged area.

Today, there are technologies with which you can independently repair a welded threshold without using a welding machine. For this, fiberglass and epoxy glue are used.

What to do if sills and pillar are damaged

If the rack is damaged simultaneously with the threshold, they are simultaneously replaced. In this case, the procedure is quite simple. First of all, the spar of the middle pillar is cut out. Before starting to straighten the side member, make sure that the car body is not damaged. After that, the installation site is thoroughly cleaned, all excess metal particles are removed at the same time.
Further, the surface of the spar is leveled and adjusted, after which the fastening and welding work is carried out - it remains only to install the doors in place and adjust all the gaps.

How can metal be treated to protect against corrosion

auto chemical protection

Compositions designed to protect the car body (anticorrosive) are divided into several categories: compositions intended for processing hidden cavities, and compositions for application to the surface of the body.

Cavity products, in turn, are divided into two categories: the first includes oil-based products that have a liquid consistency. This allows them to penetrate into the most difficult-to-reach places and fill microcracks in the paintwork. Corrosion protection is provided by the corrosion inhibitors included in the preparation - substances that slow down the corrosion process, as well as a greasy oil film that protects the metal surface from contact with moisture. The only one significant disadvantage these drugs have low mechanical strength and inability to adhere to vertical surfaces.

The second type of anticorrosive treatment for cavities is paraffin-based preparations. The corrosion inhibitors included in the composition work only when the drug is in a liquid state (that is, for some time after application). When the solvent evaporates from the drug, the inhibitors almost completely cease their effect. After drying, the preparation forms a waxy film, which completely blocks the access of oxygen to the metal. Paraffin-based formulations are not very strong, therefore they are used exclusively for treating cavities in the car body.

For application to the external surface, bitumen-based compounds are used. Bituminous mastics are produced on the basis of synthetic and bituminous resins. They simultaneously perform several tasks: they protect the bottom, arches and sills from aggressive environmental influences, and protect against mechanical damage.

Sometimes the manufacturer includes corrosion inhibitors in the mastics, but, rather, for preventive purposes. The drug will not be able to protect the exposed metal from corrosion. Much more important is its protective, "covering" properties - the mastic must adhere firmly to the surface of the metal, even after hitting stones, curbs and other obstacles.

Mastics are applied to the surface in a thick layer, which makes them a good sound insulator. Some preparations after application harden and resist mechanical stress well, but may crack, others do not dry out completely, retaining excellent elasticity, but poorly resist mechanical stress.

polishes

They are substances in the idea of ​​a paste or emulsion. Are divided into:

Recovery.
Protective.
Combined.
Wax polishes.

In the process of reducing the surface treatment with polish, scuffs, matte (oxidized) areas of the paint are partially removed, as well as small scratches... Polishing is carried out with special polishing machines... In this case, use abrasive pastes and compositions of different grain sizes.

Soft polishing is performed if the body paintwork is weakly worn, and it is only necessary to restore the gloss of the surface. Unlike restoration polishing, in this case only finishing polishing compounds are used.

anti-gravel film

Another way to protect the most vulnerable parts of the body, including sills. Each manufacturer of anti-gravel film strongly advertises its product, claiming that it is his film that possesses all necessary qualities... In fact, such advertisements are only intended to justify the high price of the product.

Cutting of the film is carried out using a computer and special electronic patterns, cutting is carried out by a plotter. Any service engaged in window tinting glues the film. It is not difficult to remove the film - all the glue remains on its surface, and not on the surface of the thresholds.

Electrochemical protection

It is an absolutely harmless way for the owner and his car to protect thresholds and other hard-to-reach places of the car body.
The principle of operation is very simple, and is based on the principle of interaction of a galvanic pair (car body and electrodes). In this case, the body plays the role of a cathode, steel plates serve as an anode. They are fixed in the most problem areas bodies where corrosion is most common. As a result of the difference in electrical potentials, the metal of the anodes is oxidized and gives up free electrons to the metal of the body, thus restoring it.

In order for the electrochemical protection to work as efficiently as possible, it is necessary to install from two to three dozen anodes on the car, the shelf life of which is up to eight years.

Plastic door sill, advantages and disadvantages

Of the advantages of plastic linings, it should be noted that they are cheap and effective. this method protection of thresholds. The plastic protects the sills well from dirt and mechanical damage.

If we talk about the shortcomings, the plastic lining cannot protect the metal from moisture, which is "taken" under it, contributing to the occurrence of corrosion. Therefore, it is recommended to install plastic door sills only after anti-corrosion treatment.

How to find and order the necessary spare parts and tools on Aliexpress at a reasonable price and free shipping

In order to find a suitable product and place an order, you must perform the following steps:

First you need to register in the system. Enter your data and email address in the Latin alphabet in the appropriate lines:

After registering in your profile, you need to enter the address to which the goods will be delivered. The address is entered only in the Latin alphabet:

We select the appropriate product, press the button “buy now, pay:

Car thresholds are very important element, which is designed to make getting into the car more comfortable. In addition, thresholds also have decorative functions - they are able to decorate any modern car... Of course, a lot depends on the correct manufacturing of the parts. If you carefully prepare and follow the algorithm, you can create stylish and reliable elements that will help improve appearance and vehicle operation.

1 Spectacular and practical motorways - buy or make yourself?

Every driver who loves his car strives in every possible way to improve it, add something new. Moreover, this applies to both the owners of "nines" and people who own prestigious Land rover and Lexus. One of the most popular options for modernizing a car today is the purchase or manufacture of car sills. The first option is suitable for busy people who have at their disposal "extra" 5-6 thousand rubles. By spending this money on the purchase and installation of elements on the car, you can save time and acquire functional and, at the same time, decorative details. Depending on the type of thresholds, their cost and prices for installation services may vary.

• - advantages and disadvantages of the operation
• – optimal way increase power!
• All aspects of choice and
• - simple and effective method increase engine power
• - we improve the style and sound
• VAZ 2107 is a stylish classic!
• - we bring the car engine to perfection

Most a budget option Is the purchase of universal removable elements. They are good because they are suitable for installation on almost any car. Such thresholds are made of more or less high-quality aluminum, covered with a special anti-corrosion compound. At correct operation universal elements can last about 2 years before they begin to deform. The price of thresholds of this type is fully consistent with the quality - from 2 to 5 thousand rubles. for a set of parts is a perfectly acceptable amount. You need to add about 2 thousand more for their installation. The only drawback of universal elements is the absence of any decorative qualities. To make such thresholds more expressive, the driver will have to separately order services for their revision. Alternatively, you can paint the thresholds.

The second option is to make the elements yourself. This great way work on a car, spending the minimum amount of money and about half a day of your time. Among the advantages of this method is the possibility of making more reliable thresholds, because to create them, you can use steel, which is several times stronger than aluminum. In addition, homemade parts can be much more effective than the same universal parts. When self-made elements, their cost will cost the owner of the car no more than 2 thousand rubles. This amount will be greatly influenced by the material from which the thresholds will be made. Reinforced parts made of titanium alloy are the most expensive, and steel elements are slightly less expensive.

2 Parts from metal pipes - a budget option for high reliability

Since the elements for the car will be made of metal, it will take some welding skills to work. If you have never worked with a welding machine, but really want to supplement your car with home-made parts, then you can just practice on other unnecessary metal elements... Before doing this, do not forget to study the safety rules and wear a protective mask and gloves.

Threshold on a car made of a metal pipe In addition to the welding machine, for the manufacture and installation of spare parts you need:

• 2 square pipes of the same length and diameter;
• 2 pieces of corrugated iron;
• bolts for fastening;
• file for metal;
• paint and acrylic varnish.

When preparing, pay special attention to pipes - this is the basis of future thresholds. They must be exactly the same. The diameter of the products directly depends on your needs. If you want to make large thresholds that would stand out in your car, then use pipes with a diameter of 7-8 cm. If it is planned to manufacture small spare parts, then it will be quite acceptable to manufacture parts from pipes with a diameter of 4 cm. The best option installation of spare parts from pipes with a diameter of 50 mm is considered. Having prepared everything you need, you can proceed with the installation. Take the first pipe and cut 4 identical pieces from it. Next, the corrugated iron must be welded to the piece that will be placed under the doors. Each of these pieces will need to be bolted under the standard car steps.

Second reliable option- without cutting off the pipes, fix them to the footboard of the car as a whole. However, this method is mainly suitable for older vehicles with fewer bends in the bodywork.

After manufacturing and subsequent installation of parts on a car, you need to take care of their decorative qualities. In principle, it will be enough that you paint the thresholds with some interesting paint. For example, you can make spare parts in matte black, or, conversely, paint them with a bright metallic paint. Some car owners go further and, in addition to painting, glue all kinds of vinyl drawings on the thresholds. This bears fruit, but after a while the drawings are erased, and they need to be changed. No matter how you act, and no matter how you make the thresholds, you will in any case receive universal reliable parts that will play not only a practical, but also a decorative role.

3 Spare parts repair - what to do in case of damage?

Regardless of whether your doorsteps are homemade or bought in a store, sooner or later they will require repair. Moreover, the maintenance of these parts directly depends on their type. For example, if your car has detachable parts, then the repair of the thresholds will be quite simple. First, you need to completely remove the spare part from the car by unscrewing the mounting bolts. Then, using a small hammer, the surface of the threshold must be leveled and repainted. Installation of the part is carried out upside-down.

Repair of a threshold for a car There are times when the thresholds need to be not just aligned, but to close the hole formed. To do this, a metal plate must be welded to the previously dismantled part, and then the element must be filed for metal. As soon as you remove all burrs and level the threshold, it will need to return to its former decorative properties - paint and apply a protective varnish. If your car has non-removable sills, then it will be a little more difficult to repair them. Firstly, all work will be carried out in the immediate vicinity of the car, so the car must be protected with thick paper or a piece of plastic. Secondly, you will need more tools: a thin and thick file for metal, pliers, a small hammer.

Thresholds for a car are very important detail despite its compactness. What are they needed for? Firstly, it makes it convenient to get into the car. It is enough to stand on the threshold, which allows you not to spin around the door. Secondly, it is a stylish look. Thresholds will decorate any car, become stylish detail drawing attention to itself. Thirdly, it is protection against various damages. Thresholds allow you to protect the body from small stones, during small collisions they take the whole blow on themselves, which also protects the car from damage.

You can buy them in the store. Do-it-yourself thresholds. They are usually made of pipes, on which flat sections are made for maximum convenience. The flat areas are covered with anti-slip material. Thus, the entrance to the car interior will be convenient and safe. There are other types of thresholds: in the form of a footboard fixed to the pipe, with a tread for maximum comfort.

Additional thresholds (footboards) can be done by hand from pipes. This option is beneficial for several reasons. Firstly, thresholds sold in stores may not suit a person, and in this case it is easier to complete them yourself. Secondly, such products may not be reliable enough, fastening of parts often does not suit car owners with their weakness. Thirdly, the cost of in-store thresholds can be greatly overestimated. Their quality may simply not match the price.

What are additional thresholds for? They also make it easier to enter the vehicle. This detail is especially relevant when elderly people and children often drive in the car, because it is often difficult for them to get into the car. In addition, the footrests make it easier to clean your shoes before getting into the car, which prevents dirt from entering the interior.

How to fulfill thresholds

First of all, before making a structure from a pipe with your own hands, we recommend that you view the training material: photos, videos. This will help you get the job done easier and faster.

The construction will require 2 pipes. Their diameter is determined depending on the needs. The best option is 50 mm. They should be tried on and trimmed. The threshold is made in the shape of the letter C, but this is variable, depending on the model of the machine. Corrugated iron is required for the footboard.

Then you should proceed with the installation. 4 pieces should be cut from a 70 mm square tube. Each part is fixed on the bolts from the bottom of the car steps. Thresholds are welded to these parts by welding. You can make the design more reliable with kerchiefs.

Pipes can be painted with black nitrate for aesthetics. The result is a robust and reliable structure that can withstand heavy loads and has a long service life. How long does it take to work? It all depends on your skills. On average, it takes half a day to make a structure from a pipe. All kinds of fittings and measurements take a lot of time.

However, the comfort is worth all the effort. Moreover, the work will require the very minimum of materials.

Thresholds on a car are a very important element that is designed to make getting into a car more comfortable. In addition, the thresholds also have decorative functions - they can decorate any modern car. Of course, a lot depends on the correct manufacturing of the parts. If you carefully prepare and follow the algorithm, you can create stylish and reliable items that will help improve the appearance and performance of the vehicle.

1

Every driver who loves his car strives in every possible way to improve it, add something new. Moreover, this applies to both the owners of "nines" and people who own the prestigious Land Rover and Lexus. One of the most popular options for modernizing a car today is the purchase or manufacture of car sills. The first option is suitable for busy people who have at their disposal "extra" 5-6 thousand rubles. By spending this money on the purchase and installation of elements on the car, you can save time and acquire functional and, at the same time, decorative details. Depending on the type of thresholds, their cost and prices for installation services may vary.

Car threshold

The most budgetary option is the purchase of universal removable elements. They are good because they are suitable for installation on almost any car. Such thresholds are made of more or less high-quality aluminum, covered with a special one. When used correctly, universal elements can last about 2 years before they begin to deform. The price of thresholds of this type is fully consistent with the quality - from 2 to 5 thousand rubles. for a set of parts is a perfectly acceptable amount. You need to add about 2 thousand more for their installation. The only drawback of universal elements is the absence of any decorative qualities. To make such thresholds more expressive, the driver will have to separately order services for their revision. Alternatively, you can.

The second option is to make the elements yourself. This is a great way to get things done with the minimum amount of money and about half a day of your time. Among the advantages of this method is the possibility of making more reliable thresholds, because to create them, you can use steel, which is several times stronger than aluminum. In addition, homemade parts can be much more effective than the same universal parts. In the case of self-production of elements, their cost will cost the owner of the car no more than 2 thousand rubles. This amount will be greatly influenced by the material from which the thresholds will be made. Reinforced parts made of titanium alloy are the most expensive, and steel elements are slightly less expensive.

2

Since the elements for the car will be made of metal, it will take some welding skills to work. If you have never worked with a welding machine, but really want to supplement your car with homemade parts, then you can just practice on other unnecessary metal elements. Before doing this, do not forget to study the safety rules and wear a protective mask and gloves.

Threshold on a car made of a metal pipe

In addition to the welding machine, for the manufacture and installation of spare parts you need:

• 2 square pipes of the same length and diameter;
• 2 pieces of corrugated iron;
• bolts for fastening;
• file for metal;
• paint and acrylic varnish.

When preparing, pay special attention to pipes - this is the basis of future thresholds. They must be exactly the same. The diameter of the products directly depends on your needs. If you want to make large thresholds that would stand out in your car, then use pipes with a diameter of 7-8 cm. If it is planned to manufacture small spare parts, then it will be quite acceptable to manufacture parts from pipes with a diameter of 4 cm. The best option is to install spare parts from pipes with a diameter of 50 mm. Having prepared everything you need, you can proceed with the installation. Take the first pipe and cut 4 identical pieces from it. Next, the corrugated iron must be welded to the piece that will be placed under the doors. Each of these pieces will need to be bolted under the standard car steps.

The second reliable option is to fix the pipes entirely to the footboard of the car without cutting off the pipes. However, this method is mainly suitable for older vehicles with fewer bends in the bodywork.

After manufacturing and subsequent installation of parts on a car, you need to take care of their decorative qualities. In principle, it will be enough that you paint the thresholds with some interesting paint. For example, you can make spare parts in matte black, or, conversely, paint them with a bright "metallic" paint. Some car owners go further and, in addition to painting, glue all kinds of vinyl drawings on the thresholds. This bears fruit, but after a while the drawings are erased, and they need to be changed. No matter how you act, and no matter how you make the thresholds, you will in any case receive universal reliable parts that will play not only a practical, but also a decorative role.

3

Regardless of whether your doorsteps are homemade or bought in a store, sooner or later they will require repair. Moreover, the maintenance of these parts directly depends on their type. For example, if your car has detachable parts, it will be done quite simply. First, you need to completely remove the spare part from the car by unscrewing the mounting bolts. Then, using a small hammer, the surface of the threshold must be leveled and repainted. Installation of the part is carried out upside-down.

Repair of a threshold for a car

There are times when the thresholds need to be not just aligned, but to close the hole formed. To do this, a metal plate must be welded to the previously dismantled part, and then the element must be filed for metal. As soon as you remove all burrs and level the threshold, it will need to return to its former decorative properties - paint and apply a protective varnish. If your car has non-removable sills, then it will be a little more difficult to repair them. Firstly, all work will be carried out in the immediate vicinity of the car, so the car must be protected with thick paper or a piece of plastic. Secondly, you will need more tools: a thin and thick file for metal, pliers, a small hammer.

First you need to identify the problem with a non-removable threshold. If it is a deformation, then the alignment of the part will be carried out using pliers and a hammer. We take pliers in one hand and hold the threshold with them, and with the other hand with a hammer we level it. If a dent has formed on the threshold, which is very difficult to level with a hammer, then for repair you need to use special tool to align dents. It is sold in any car dealership. A third, less common method is welding in the area of ​​the steel bar indentation. After that, the rod must be grasped with pliers and pulled towards you. Thus, it is possible to return the thresholds to their former shape. After repair, the rod needs to be cut and the parts painted.

X Do you still think that car diagnostics is difficult?

If you are reading these lines, then you have an interest in doing something yourself in the car and really save because you already know that:

• STO lomat big money for simple computer diagnostics
• To find out the error, you need to go to the specialists
• Simple wrenches work in the services, but you can't find a good specialist

And of course you are tired of throwing money down the drain, and there is no question of driving around the service station all the time, then you need a simple ROADGID S6 Pro AUTOSCANNER that connects to any car and through an ordinary smartphone you will always find a problem, extinguish CHECK and it's good save !!!

We have tested this scanner ourselves on different cars and it showed excellent results, now we recommend it to EVERYONE! So that you do not fall for chinese fake, we publish here a link to the official site of the AutoScanner.

For many car enthusiasts, it has already become not a necessity, a need to improve the car, but rather a favorite pastime, a hobby. This is the way of life of a car owner, his way of self-expression and the opportunity to distinguish his favorite car among hundreds of thousands of others. Tuning of the car body for the most part refers to the aesthetic types of tuning, although they can be improved and technical specifications cars. This is the most visual kind of tuning. The results of improving the body or its individual parts delight the eye not only of the car owner himself, but also of everyone around him. You can tune almost everything - from thresholds and door handles to the trunk lid, hood or roof of the vehicle.

Tuning car thresholds

Beautiful body tuning will give your car a unique look

One of the most popular types external tuning the manufacture of door sills is considered. This is the easiest way to improve the appearance of a car, which almost everyone can do. The easiest way, of course, will be to buy a ready-made version of the linings and just install them in the right place. Or drive the car to a car service, where they will do everything for you. However, it is much more interesting and cheaper to install and make thresholds on a car with your own hands.

What is needed for this? The first is to make the door sills yourself. You can make them from metal, wall panels or even foam.

Foam thresholds are the easiest to make. To do this, you need a piece of styrofoam, fiberglass, paint, primer and putty. Cut out the required threshold from the polystyrene in shape and size, cover it with fiberglass several times, glue it in the right place. After that, putty, priming and painting are performed. However, this option for making linings is the least reliable.

The strongest, of course, will be metal thresholds, but in order to do everything yourself, you will need skills in working with welding and metal. In addition, the design itself will cost you a lot. That is why sill covers are most often made of wall panels. They need a minimum of skills and funds for this. In order to make such door sills, it will be necessary to purchase wall panels, self-tapping screws and drywall guides, as well as anticorrosive agent, epoxy resin, varnish, paint, putty and primer. After purchasing everything you need, proceed to the manufacture and installation. First, you need to drill a hole in the body for self-tapping screws and treat everything with an anti-corrosion compound. After that, using self-tapping screws, fasten the drywall guides and, to them, the panels. Then, for greater rigidity of the structure, wrap it with fiberglass impregnated with epoxy glue. After everything is dry, you can proceed to the primer, putty, painting and varnishing of the resulting structure.

We modernize the trunk of the car

Quite often, car owners are also interested in tuning the trunk. Someone is striving to make it more functional, trying to increase the space, or making sheathing with panels, attaches special shelves, clamps for more convenient transportation of cargo.

Others prefer chrome trims, spoilers and ladders. Such tuning of the trunk allows you to give the car a sportier and more aggressive look. However, most often it is interesting to owners of large cars.

Still others focus on improving acoustic parameters or try to make opening and closing of luggage racks more convenient. For example, they make an additional fifth door handle or an electrically conductive lock.

Consider how to make a simple tuning of the trunk with your own hands, namely, install the chrome lining on the trunk, a handle for closing and an electric lock.

Installation of the electric drive of the lock

Tuning the trunk, namely the installation of an electric lock drive, can significantly simplify the life of the car owner. In order to open the trunk you need keys, and for this you have to turn off the car every time. Installing an electric drive solves this problem. How to install and connect everything? First of all, you need to buy the electric drive itself, a new lock for it, a fuse holder, terminals, electrical tape and wires. You will also need tools: wrenches, screwdrivers and pliers.

After all necessary materials purchased, proceed to the process of dismantling the old castle. Remove the plastic boot lining and dismantle the old lock. After that, you should disconnect the car from the power supply and you can proceed to the wiring. It is best to connect from the cigarette lighter, the button itself can be installed in any place convenient for you. A fuse must be installed between the cigarette lighter and the button of the electric drive. Next, make the power harness using electrical blocks and lay the wiring on the thresholds of the machine luggage compartment... After that, it is necessary to install the electric actuator and a new lock in the already existing hole.

Next, go directly to the connection of the electric drive. In this case, it is very important to do everything in accordance with the instructions of the electric drive itself and observe the polarity, otherwise the lock will not open. After everything is connected, isolate the connection points, turn on the battery and check the operation. So, now you have no problems with opening, now you need to simplify its closing.

Installing an additional handle

The second stage of tuning the trunk is to install an additional handle to close the trunk. Here, too, everything is simple. Most often, such a handle is installed with inside... This will not only make it easier for you to close, but also will not affect the appearance of the machine. ... To do this, buy an ordinary plastic handle for a car and attach it with self-tapping screws to the edge of the inside of the trunk. This way, you have a handle that is always clean and dry, with which you can easily slam the trunk.

Installation of chrome strips

After you figured out the functional side of the modernization, proceed to the installation of the chrome trim. To do this, you just need to buy a chrome trim for the trunk for your car brand, degrease the installation site and, by removing protective film from the adhesive side, glue it in the required place.

You can similarly decorate your car with chrome trims in other places. Quite often, chrome trims are installed on the hood, the radiator grill, or even with their help they make tuning the roof of the car.

conclusions

Body tuning is becoming more and more popular today. Almost everyone strives to change something during external appearance or the functionality of your car. And he tries to do it on his own, with his own hands. After all, most of the work is carried out quite simply and does not require special skills. All you need is imagination, a little material and a desire to do something. While for the most part body tuning does not affect the functionality of the car, it is a great way to decorate your car yourself.

The best prices and conditions for the purchase of new cars

Credit 6.5% / Installment / Trade-in / 98% of approvals / Gifts in the salon

Mas Motors